Our Product / Services
Solar Panel
2 Products availableSolar Power Plant Installation
1 Services availableBusiness Management Consultants
1 Services availableGenerators
1 Products availableAir Conditioners
1 Products availableInverters
1 Products availableOur product range contains a wide range of Evacuated Tube Collector Solar Water Heater (500 LPD), Evacuated Tube Collector Solar Water Heater (200 LPD), Flat Plate Collector Solar Water Heater (200 LPD), Flat Plate Collector Solar Water Heater (1000 LPD) and Flat Plate Collector Solar Water Heater (100 LPD)
Buy high performance, easy to install and low maintenance Evacuated Tube Collector Solar Water Heater (500 LPD) from us at competitive prices. Reckoned for its user-friendliness, high output and low power consumption, our Evacuated Tube Collector Solar Water Heater (500 LPD) is of unmatched standards. We can provide the customized version of the model as well.
Specifications
| Capacity of Tanks | 500 LPD(250LPD x 2 No’s) |
|---|---|
| Material | Stainless Steel /GRP/Boiler grade steel. |
| Type | Cylindrical – horizontally assembled. |
| Size | Ø460, Length 2285. |
| Insulation | P U F.40-50mm. |
| Outer Cladding | Pre coated galvanized Slab/Aluminum. |
| Outer Finishing | Pure Polyester Powder Coating finish. |
| Outer Finish Color | Golden Yellow & Black combination. |
| Back up Heater | 2 KW With thermostat control 230V AC. |
| Tank Supports | Fabricated Stainless steel. |
| Tank Testing | Factory pressure tested for normal systems is at 1 Kg/cm². |
| Normal Working pressure of the system | Less than 0.3 Kg/cm². |
| Number of Tubes | 60 No’s |
| Evacuated Tube Dimensions | Outer Diameter - 47± 0.7.mm, Inner Diameter- 37±0.7.mm |
| Total Tube length | 1500±5mm. |
| Type of tube selective coating | Graded Al-N with Copper under Coating |
| Configuration of Glass Tubes | Two Concentric Borosilicate Glass Tubes. |
| Solar absorbance | >0.93. |
| Solar Emmitance. (at 80°C) | <0.06. |
| Evacuation between Outer & Inner Tubes | 5×10-3 Pa. |
| Rated Pressure | 0.1. Mpa. (1.Kg/Cm²) |
| Stagnation Temperature | <300°C |
We are engaged in designing, fabricating and trading of Evacuated Tube Collector Solar Water Heater (200 LPD). Manufactured using the latest CAD/ CAM technologies, our Evacuated Tube Collector Solar Water Heater (200 LPD) is easy to assemble on site and guarantee long service. Buyers can purchase the model from us in bulk and get it customized to meet specific requirements.
Specifications
| Capacity of Tanks | 200 LPD |
|---|---|
| Material | Stainless Steel /GRP/Boiler grade steel. |
| Type | Cylindrical – horizontally assembled. |
| Size | Ø460, Length 2110. |
| Insulation | P U F.40-50mm. |
| Outer Cladding | Pre coated galvanized Steel/Aluminum. |
| Outer Finishing | Pure Polyester Powder Coating finish. |
| Outer Finish Color | Golden Yellow & Black combination. |
| Back up Heater | 2 KW With thermostat control 230V AC. |
| Tank Supports | Fabricated Stainless steel. |
| Tank Testing | Factory pressure tested for normal systems is at 1 Kg/cm². |
| Normal Working pressure of the system | Less than 0.3 Kg/cm². |
| Number of Tubes | 28 No’s |
| Evacuated Tube Dimensions | Outer Diameter - 47± 0.7.mm, Inner Diameter- 37±0.7.mm |
| Total Tube length | 1500±5mm. |
| Type of tube selective coating | Graded Al-N with Copper under Coating |
| Configuration of Glass Tubes | Two Concentric Borosilicate Glass Tubes. |
| Solar absorbance | >0.93. |
| Solar Emmitance. (at 80°C) | <0.06. |
| Evacuation between Outer & Inner Tubes | 5 × 10-3 Pa. |
| Rated Pressure | 0.1. Mpa. (1.Kg/Cm²) |
| Stagnation Temperature | <300°C |
Customers can obtain our range of Flat Plate Collector Solar Water Heater (200 LPD). We fabricate the Solar Water Heater in adherence to norms set by industrial regulatory bodies. We are capable of delivering small or bulk orders of Solar Water Heater to our buyers in domestic and international markets.
Specifications
|
Material & Thickness |
Stainless Steel – 304/GRP/Boiler grade steel. |
|---|---|
|
Type |
Cylindrical – horizontally assembled. |
|
Size |
Ø360, Length 1800. |
|
Insulation |
P U F.40-50mm. |
|
Outer Cladding |
Pre coated galvanized Steel/Aluminum. |
|
Outer Finishing |
Pure Polyester Powder Coating finish. |
|
Outer Finish Color |
Golden Yellow & Black combination. |
|
Back up Heater |
2 KW With thermostat control 230V AC. |
|
Tank Supports |
Fabricated and powder coated M.S. Tube |
|
Tank Testing |
Factory pressure tested for normal systems is at 2 Kg/cm². |
|
Normal Working pressure of the system |
Less than 1 Kg/cm². |
|
Interconnection Tank and Collector |
EPDM Pipe |
|
No. of Collectors |
02 No. |
|
Type |
Copper, selectively coated with “NALSUN” Black Chrome coating. |
|
Size |
2080mm L x 1050mm W x 100mm H |
|
Absorber Material |
Copper - Copper absorber. |
|
No. of Fins |
9 No’s per collector |
|
Header Tubes |
Copper, Ø25 mm, 22 SWG. |
|
Riser Tubes |
Copper, Ø12.5 mm, 24 SWG |
|
Header Protective coating |
Polyurethane based coating |
|
Riser to Fin Joining |
Ultra Sonic Metal welding |
|
Collector Box |
Aluminum |
|
Protective coating on Collector Box |
Pure Polyester powder coated - Golden Yellow |
|
Glass retaining angle / Aluminum |
25mm Pure Polyester Powder coated - Black |
|
Collector back sheet |
Aluminum Screwed to the frame |
|
Back, Corner Sealing |
Non Acidic Silicon sealant through corners and screw joint |
|
Top Cover/Glazing |
Toughened glass, 4mm thick |
|
Glass Beading |
High quality EPDM Rubber - Single Piece |
|
Absorber Flanges |
4 mm Thick Machined brass flanges, 63 mm dia, 4 bolt holes |
|
Gaskets and Grommets |
High quality EPDM special shaped full Gaskets and Grommets |
|
Insulation Bottom |
Rock wool, 50 mm 48 kg/m³ density |
|
Insulation Side |
Rock wool, 25 mm 48 Kg/m³ density |
|
Reflective foil |
Aluminum 50 microns thick for bottom and 0.45 mm for sides |
|
Collector Supports |
Fabricated and Duly powder coated Mild Steel Sections |
Get in touch with us for obtaining Flat Plate Collector Solar Water Heater (1000 LPD). The extremely efficient Solar Water Heater we offer has garnered huge appreciation across the world. Customers can purchase the Solar Water Heater from us and be assured of receiving a quality product within postulated time.
Specifications
| Material & Thickness | Stainless Steel – 304/GRP/Boiler grade steel. |
|---|---|
| Type | Cylindrical – horizontally assembled. |
| Size | Ø700, Length 2600. |
| Insulation | Rockwool OR Glass wool of 100mm thick. |
| Outer Cladding | Pre coated galvanized Steel/Aluminum. |
| Outer Finishing | Pure Polyester Powder Coating finish. |
| Outer Finish Color | Golden Yellow & Black combination. |
| Back up Heater | 2 KW × 3 No’s With thermostat control 230 V AC. |
| Tank Supports | Fabricated and powder coated M.S. Angle |
| Tank Testing | Factory pressure tested for normal systems is at 8 Kg/cm². |
| Normal Working pressure of the system | Less than 4 Kg/cm². |
| Interconnection Tank and Collector | EPDM Pipe |
| No. of Collectors | 08 No. |
|---|---|
| Type | Copper, selectively coated with “NALSUN” Black Chrome coating. |
| Size | 2080mm L x 1050mm W x 100mm H |
| Absorber Material | Copper - Copper absorber. |
| No. of Fins | 9 No’s per collector |
| Header Tubes | Copper, Ø25 mm, 22 SWG. |
| Riser Tubes | Copper, Ø12.5 mm, 24 SWG |
| Header Protective coating | Polyurethane based coating |
| Riser to Fin Joining | Ultra Sonic Metal welding |
| Collector Box | Aluminum |
| Protective coating on Collector Box | Pure Polyester powder coated - Golden Yellow |
| Glass retaining angle / Aluminum | 25mm Pure Polyester Powder coated - Black |
| Collector back sheet | Aluminum Screwed to the frame |
| Back, Corner Sealing | Non Acidic Silicon sealant through corners and screw joint |
| Top Cover/Glazing | Toughened glass, 4mm thick |
| Glass Beading | High quality EPDM Rubber - Single Piece |
| Absorber Flanges | 4 mm Thick Machined brass flanges, 63 mm dia, 4 bolt holes |
| Gaskets and Grommets | High quality EPDM special shaped full Gaskets and Grommets |
| Insulation Bottom | Rock wool, 50 mm 48 kg/m³ density |
| Insulation Side | Rock wool, 25 mm 48 Kg/m³ density |
| Reflective foil | Aluminum 50 microns thick for bottom and 0.45 mm for sides |
| Collector Supports | Fabricated and Duly powder coated Mild Steel Sections |
We are offering Flat Plate Collector Solar Water Heater (100 LPD) to our valued customers across the globe. Our Solar Water Heater is noted for features like efficient performance and smooth operation. Customers can rely on us for swiftly delivering Flat Plate Solar Water Heater to any part of the world.
Solar Water Heater 100 LPD Capacity Type FPC
| Material & Thickness | Stainless Steel – 304/GRP/Boiler grade steel. |
|---|---|
| Type | Cylindrical – horizontally assembled. |
| Size | Ø360, Length 1800. |
| Insulation | P U F.40-50mm. |
| Outer Cladding | Pre coated galvanized Steel/Aluminum. |
| Outer Finishing | Pure Polyester Powder Coating finish. |
| Outer Finish Color | Golden Yellow & Black combination. |
| Back up Heater | 2 KW With thermostat control 230V AC. |
| Tank Supports | Fabricated and powder coated M.S. Tube |
| Tank Testing | Factory pressure tested for normal systems is at 2 Kg/cm². |
| Normal Working pressure of the system | Less than 1 Kg/cm². |
| Interconnection Tank and Collector | EPDM Pipe |
| No. of Collectors | 02 No. |
|---|---|
| Type | Copper, selectively coated with “NALSUN” Black Chrome coating. |
| Size | 2080mm L x 1050mm W x 100mm H |
| Absorber Material | Copper - Copper absorber. |
| No. of Fins | 9 No’s per collector |
| Header Tubes | Copper, Ø25 mm, 22 SWG. |
| Riser Tubes | Copper, Ø12.5 mm, 24 SWG |
| Header Protective coating | Polyurethane based coating |
| Riser to Fin Joining | Ultra Sonic Metal welding |
| Collector Box | Aluminum |
| Protective coating on Collector Box | Pure Polyester powder coated - Golden Yellow |
| Glass retaining angle / Aluminum | 25mm Pure Polyester Powder coated - Black |
| Collector back sheet | Aluminum Screwed to the frame |
| Back, Corner Sealing | Non Acidic Silicon sealant through corners and screw joint |
| Top Cover/Glazing | Toughened glass, 4mm thick |
| Glass Beading | High quality EPDM Rubber - Single Piece |
| Absorber Flanges | 4 mm Thick Machined brass flanges, 63 mm dia, 4 bolt holes |
| Gaskets and Grommets | High quality EPDM special shaped full Gaskets and Grommets |
| Insulation Bottom | Rock wool, 50 mm 48 kg/m³ density |
| Insulation Side | Rock wool, 25 mm 48 Kg/m³ density |
| Reflective foil | Aluminum 50 microns thick for bottom and 0.45 mm for sides |
| Collector Supports | Fabricated and Duly powder coated Mild Steel Sections |
We are ranked among responsive and responsible traders of Evacuated Tube Collector Solar Water Heater (300 LPD). With the aide of ultramodern Cad/ CAM technologies, the Evacuated Tube Collector Solar Water Heater (300 LPD) are manufactured. The model is appreciated in the industry for its reliability and long service life. Buyers can purchase it from us at market leading prices.
Specifications
| Capacity of Tanks | 300 LPD(200LPD+100LPD) |
|---|---|
| Material | Stainless Steel /GRP/Boiler grade steel. |
| Type | Cylindrical – horizontally assembled. |
| Size | Ø460, Length 2110.(200LPD) Ø460, Length 1000.(100LPD) |
| Insulation | P U F.40-50mm. |
| Outer Cladding | Pre coated galvanized Slab/Aluminum. |
| Outer Finishing | Pure Polyester Powder Coating finish. |
| Outer Finish Color | Golden Yellow & Black combination. |
| Back up Heater | 2 KW With thermostat control 230V AC. |
| Tank Supports | Fabricated Stainless steel. |
| Tank Testing | Factory pressure tested for normal systems is at 1 Kg/cm². |
| Normal Working pressure of the system | Less than 0.3 Kg/cm². |
| Number of Tubes | 42 No’s |
| Evacuated Tube Dimensions | Outer Diameter - 47± 0.7.mm, Inner Diameter- 37±0.7.mm |
| Total Tube length | 1500.±5mm. |
| Type of tube selective coating | Graded Al-N with Copper under Coating |
| Configuration of Glass Tubes | Two Concentric Borosilicate Glass Tubes. |
| Solar absorbance | >0.93. |
| Solar Emmitance. (at 80°C) | <0.06. |
| Evacuation between Outer & Inner Tubes | 5 X 10-3 Pa. |
| Rated Pressure | 0.1. Mpa. (1.Kg/Cm²) |
| Stagnation Temperature | <300°C |
We bring forth an exclusive range of Flat Plate Collector Solar Water Heater (300 LPD). We check the Flat Plate Solar Water Heater on stringent quality parameters before approving for delivery. We are offering the Flat Plate Collector Solar Water Heater to buyers all over the world at highly affordable rates.
Specifications
|
Material & Thickness |
Stainless Steel – 304/GRP/Boiler grade steel. |
|---|---|
|
Type |
Cylindrical – horizontally assembled. |
|
Size |
Ø550, Length 1230. |
|
Insulation |
P U F.40-50mm. |
|
Outer Cladding |
Pre coated galvanized Steel/Aluminum. |
|
Outer Finishing |
Pure Polyester Powder Coating finish. |
|
Outer Finish Color |
Golden Yellow & Black combination. |
|
Back up Heater |
2 KW With thermostat control 230V AC. |
|
Tank Supports |
Fabricated and powder coated M.S. Angle |
|
Tank Testing |
Factory pressure tested for normal systems is at 2 Kg/cm². |
|
Normal Working pressure of the system |
Less than 1 Kg/cm². |
|
Interconnection Tank and Collector |
EPDM Pipe |
| No. of Collectors | 03 No. |
|---|---|
| Type | Copper, selectively coated with “NALSUN” Black Chrome coating. |
| Size | 2080mm L x 1050mm W x 100mm H |
| Absorber Material | Copper - Copper absorber. |
| No. of Fins | 9 No’s per collector |
| Header Tubes | Copper, Ø25 mm, 22 SWG. |
| Riser Tubes | Copper, Ø12.5 mm, 24 SWG |
| Header Protective coating | Polyurethane based coating |
| Riser to Fin Joining | Ultra Sonic Metal welding |
| Collector Box | Aluminum |
| Protective coating on Collector Box | Pure Polyester powder coated - Golden Yellow |
| Glass retaining angle / Aluminum | 25mm Pure Polyester Powder coated - Black |
| Collector back sheet | Aluminum Screwed to the frame |
| Back, Corner Sealing | Non Acidic Silicon sealant through corners and screw joint |
| Top Cover/Glazing | Toughened glass, 4mm thick |
| Glass Beading | High quality EPDM Rubber - Single Piece |
| Absorber Flanges | 4 mm Thick Machined brass flanges, 63 mm dia, 4 bolt holes |
| Gaskets and Grommets | High quality EPDM special shaped full Gaskets and Grommets |
| Insulation Bottom | Rock wool, 50 mm 48 kg/m³ density |
| Insulation Side | Rock wool, 25 mm 48 Kg/m³ density |
| Reflective foil | Aluminum 50 microns thick for bottom and 0.45 mm for sides |
| Collector Supports | Fabricated and Duly powder coated Mild Steel Sections |
Buyers can purchase Evacuated Tube Collector Solar Water Heater (100 LPD) from us at market leading prices. We guarantee the model is high performance, easy to install and renders a long service life. We can customize it as per power and capacity requirement of buyers. We offer Evacuated Tube Collector Solar Water Heater (100 LPD) in bulk and promise to make timely delivery.
Specifications
| Capacity of Tanks | 100 LPD |
|---|---|
| Material | Stainless Steel /GRP/Boiler grade steel. |
| Type | Cylindrical – horizontally assembled. |
| Size | Ø460, Length 1000. |
| Insulation | P U F.40-50mm. |
| Outer Cladding | Pre coated galvanized Steel/Aluminum. |
| Outer Finishing | Pure Polyester Powder Coating finish. |
| Outer Finish Color | Golden Yellow & Black combination. |
| Back up Heater | 2 KW With thermostat control 230V AC. |
| Tank Supports | Fabricated Stainless steel. |
| Tank Testing | Factory pressure tested for normal systems is at 1 Kg/cm². |
| Normal Working pressure of the system | Less than 0.3 Kg/cm². |
| Number of Tubes | 14 No’s |
| Evacuated Tube Dimensions | Outer Diameter - 47± 0.7.mm, Inner Diameter- 37±0.7.mm |
| Total Tube length | 1500.±5mm. |
| Type of tube selective coating | Graded Al-N with Copper under Coating |
| Configuration of Glass Tubes | Two Concentric Borosilicate Glass Tubes. |
| Solar absorbance | >0.93. |
| Solar Emmitance. (at 80°C) | <0.06. |
| Evacuation between Outer & Inner Tubes | 5 X 10-3 Pa. |
| Rated Pressure | 0.1. Mpa. (1.Kg/Cm²) |
| Stagnation Temperature | <300°C |
Made from premium quality materials, we are offering a reliable range of Flat Plate Collector Solar Water Heater (400 LPD). We meticulously package the Solar Water Heater in durable materials so there is no risk of defect during storage or transportation. We are offering the Flat Plate Collector Solar Water Heater to buyers at nominal prices.
Specifications
| Material & Thickness | Stainless Steel – 304/GRP/Boiler grade steel. |
|---|---|
| Type | Cylindrical – horizontally assembled. |
| Size | Ø700mm, Length 1235mm. |
| Insulation | P U F.40-50mm. |
| Outer Cladding | Pre coated galvanized Steel/Aluminum. |
| Outer Finishing | Pure Polyester Powder Coating finish. |
| Outer Finish Color | Golden Yellow & Black combination. |
| Back up Heater | 2 KW With thermostat control 230V AC. |
| Tank Supports | Fabricated and powder coated M.S. Angle |
| Tank Testing | Factory pressure tested for normal systems is at 2 Kg/cm². |
| Normal Working pressure of the system | Less than 1 Kg/cm². |
| Interconnection Tank and Collector | EPDM Pipe |
| No. of Collectors | 04 Nos. |
|---|---|
| Type | Copper, selectively coated with “NALSUN” Black Chrome coating. |
| Size | 2080mm L x 1050mm W x 100mm H |
| Absorber Material | Copper - Copper absorber. |
| No. of Fins | 9 No’s per collector |
| Header Tubes | Copper, Ø25 mm, 22 SWG. |
| Riser Tubes | Copper, Ø12.5 mm, 24 SWG |
| Header Protective coating | Polyurethane based coating |
| Riser to Fin Joining | Ultra Sonic Metal welding |
| Collector Box | Aluminum |
| Protective coating on Collector Box | Pure Polyester powder coated - Golden Yellow |
| Glass retaining angle / Aluminum | 25mm Pure Polyester Powder coated - Black |
| Collector back sheet | Aluminum Screwed to the frame |
| Back, Corner Sealing | Non Acidic Silicon sealant through corners and screw joint |
| Top Cover/Glazing | Toughened glass, 4mm thick |
| Glass Beading | High quality EPDM Rubber - Single Piece |
| Absorber Flanges | 4 mm Thick Machined brass flanges, 63 mm dia, 4 bolt holes |
| Gaskets and Grommets | High quality EPDM special shaped full Gaskets and Grommets |
| Insulation Bottom | Rock wool, 50 mm 48 kg/m³ density |
| Insulation Side | Rock wool, 25 mm 48 Kg/m³ density |
| Reflective foil | Aluminum 50 microns thick for bottom and 0.45 mm for sides |
| Collector Supports | Fabricated and Duly powder coated Mild Steel Sections |
We are offering precision-engineered, low maintenance and reliable Evacuated Tube Collector Solar Water Heater (250 LPD). Our company designs, fabricates and trades the model and offer excellent technical/ after sales support for it. Buyers can purchase Evacuated Tube Collector Solar Water Heater (250 LPD) from us in bulk and expect on time delivery of consignments.
Specifications
| Capacity of Tanks | 250 LPD |
|---|---|
| Material | Stainless Steel /GRP/Boiler grade steel. |
| Type | Cylindrical – horizontally assembled. |
| Size | Ø460, Length 2285. |
| Insulation | P U F.40-50mm. |
| Outer Cladding | Pre coated galvanized Steel/Aluminum. |
| Outer Finishing | Pure Polyester Powder Coating finish. |
| Outer Finish Color | Golden Yellow & Black combination. |
| Back up Heater | 2 KW With thermostat control 230V AC. |
| Tank Supports | Fabricated Stainless steel. |
| Tank Testing | Factory pressure tested for normal systems is at 1 Kg/cm². |
| Normal Working pressure of the system | Less than 0.3 Kg/cm². |
| Number of Tubes | 30 No’s |
| Evacuated Tube Dimensions | Outer Diameter - 47± 0.7.mm, Inner Diameter- 37±0.7.mm |
| Total Tube length | 1500±5mm. |
| Type of tube selective coating | Graded Al-N with Copper under Coating |
| Configuration of Glass Tubes | Two Concentric Borosilicate Glass Tubes. |
| Solar absorbance | >0.93. |
| Solar Emmitance. (at 80°C) | <0.06. |
| Evacuation between Outer & Inner Tubes | 5×10-3 Pa. |
| Rated Pressure | 0.1. Mpa. (1.Kg/Cm²) |
| Stagnation Temperature | <300°C |
