Walnut Innovations

Ayad, Surguja, Rajasthan

Two of three phase motor currents are monitored by current transformers. The internal solid state circuitry compares with preset current level.When load currents exceeds the preset trip level, red LED iIIuminates, after the preset time, the device trips, and changes internal SPDT relaycontacts.Red LED remains illuminated indicating an overload trip has occurred. Until manual or remote electrical reset by interrupting supply, is initiated.If load current falls off below setpoint before preset delay, device resets trip timer. With the aid of LED flashing at 100% ofpreset load, actual load currents can be determined without the aid of Ammeter. Test button provides the means of testing service-worthinessand integrity of the device. Internal relay iS energized in normal operation condition(failsafe) and will not become ready mode with eithersupply lost or own failure.

*Starting delay range : O.230 seconds.*Trip delay time range:0.2-10 seconds.*May be used as electronic shearpin by setting trip time to minimum.

Specifications:1.Phase Loss Protection2.Typical Wiring3.Compact Design4. Multiple Protection Functions5.Wide Current Adjustment Range (10: 1)6.Ammeter Function7.Trip Indication LED8.High Accuracy9.Manual Instantaneous Reset10.Electrical Remote Reset11.Test Function12.Ambient Insensitive13.Low Energy Consumption14. Fail-safe Operation (No Volt Release)

Wide Adjustment Range:Has wide current adjustment range of over 10.1 .Current Setting:-*a)Type 05:0.5-6A*b)Type30:3-30A*c)Type60:5-60AControl Voltage(50/60Hz)*a)220:90-260VAC*b)440:320-480VAC

Output Relaya)Mode: 1-SPDT(1C)*b)Rating:3A/250VAC Resistive*c)Status: Normally EnergizedTime-Current Characteristic:Definite;Operating (Trip) Indication:-2LED

Two of three phase motor currents are monitored by current transformers. The internal solid state circuitry compares with preset current level.When load currents exceeds the preset trip level, red LED iIIuminates, after the preset time, the device trips, and changes internal SPDT relaycontacts.Red LED remains illuminated indicating an overload trip has occurred. Until manual or remote electrical reset by interrupting supply, is initiated.If load current falls off below setpoint before preset delay, device resets trip timer. With the aid of LED flashing at 100% ofpreset load, actual load currents can be determined without the aid of Ammeter. Test button provides the means of testing service-worthinessand integrity of the device. Internal relay iS energized in normal operation condition(failsafe) and will not become ready mode with eithersupply lost or own failure.

*Starting delay range : O.230 seconds.*Trip delay time range:0.2-10 seconds.*May be used as electronic shearpin by setting trip time to minimum.

Specifications:1.Phase Loss Protection2.Typical Wiring3.Compact Design4. Multiple Protection Functions5.Wide Current Adjustment Range (10: 1)6.Ammeter Function7.Trip Indication LED8.High Accuracy9.Manual Instantaneous Reset10.Electrical Remote Reset11.Test Function12.Ambient Insensitive13.Low Energy Consumption14. Fail-safe Operation (No Volt Release)

Wide Adjustment Range:Has wide current adjustment range of over 10.1 .Current Setting:-*a)Type 05:0.5-6A*b)Type30:3-30A*c)Type60:5-60AControl Voltage(50/60Hz)*a)220:90-260VAC*b)440:320-480VAC

Output Relaya)Mode: 1-SPDT(1C)*b)Rating:3A/250VAC Resistive*c)Status: Normally EnergizedTime-Current Characteristic:Definite;Operating (Trip) Indication:-2LED

Remote control via your mobile phone, Work anywhere in the world where there is GSM cell phone network.

This GSM Switch allows switching almost any Industrial or household appliances On or OFF remotely via mobile network.

Simply call a number and if the number calling 'Caller ID' is known, then one of the on-board relays is switched to control connected equipment such as lights, gates, doors, heating and more.

User can Control & Monitor Machinery / Automobiles / Irrigation pump sets / lights / Heating / Security systems / Tank level / Remote servers & routers, Industrial, Home & Office appliances by any Mobile or Land line phone from anywhere in the world.

Technical Specifications :-

Micro controller Based

Multifunction programmable

SMS & DTMF Based functioning (call based)

Programmable relay latching

Optically Isolated 5 Relay output C NC

Operating temperature -20C to 60C

Weight 400gm

Remote control via your mobile phone, Work anywhere in the world where there is GSM cell phone network.

This GSM Switch allows switching almost any Industrial or household appliances On or OFF remotely via mobile network.

Simply call a number and if the number calling 'Caller ID' is known, then one of the on-board relays is switched to control connected equipment such as lights, gates, doors, heating and more.

User can Control & Monitor Machinery / Automobiles / Irrigation pump sets / lights / Heating / Security systems / Tank level / Remote servers & routers, Industrial, Home & Office appliances by any Mobile or Land line phone from anywhere in the world.

Features:1. Easy to operate by call or SMS2. High grade ABS unbreakable plastic case3. Up to 100 different mobile phone numbers can be pre-set in the system4. Secure - Using caller ID for identification, unknown callers are ignored5. No need to provide a remote control for different users6. Can be operated from anywhere, no distance limit7. Can be used for authorized door access, controlling gates, switching of remote equipments, car parking systems8. Great for control of home electrical devices such as lamp, computer, refrigerator, TV, wireless router and so on

Technical Specifications :-

Micro controller Based

Multifunction programmable

SMS & DTMF Based functioning (call based)

Programmable relay latching

Optically Isolated 2 Relay output C NC

Operating temperature -20C to 60C

Weight 350gm