Molecular Sieve Sieve 3A is an alkali alumino silicate. It is the potassium form of the molecular sieve type A and has an effective pore opening of about 3 angstroms (0.3 nm).
Typical Chemical Formula : 0.45 K₂O – 0.55Na₂O Al2O₃ -2SiO₂ - nH₂O

ApplicationsMolecular Sieves 3A is commonly used for the following applications :

• Drying of unsaturated hydrocarbons (such as ethylene, propylene & butadiene), cracked gas streams, natural gas where COS minimization is required, methane, ethane and of polar compounds such as methanol and ethanol, 2-Propanol, Acetone, Acetonitrile, Acrylonitrile, Dimethyl Sulfoxide.
• Static (non regenerative) removal of H2O and volatile organic vapours from gas filled insulating glass units, Sulphur Hexafluoride and from refrigerant gases
• Molecular Sieve 3A will adsorb molecules with a kinetic diameter of less than 0.3 nm and exclude those larger.

Type : Standard 3A Grade is also available in powder form.

Regeneration : Molecular Sieve 3A can be regenerated by evacuating or purging, usually at elevated temperatures. The purge gas temperature must be sufficiently high to bring the molecular sieve to a level of 1800C to 2500C, but not exceeding 3000C. Higher temperatures may cause physical degradation of the molecular sieve structure. When used to dry streams containing olefins, a purge at lower temperature is advised to prevent polymerization during regeneration. The degree of regeneration depends on the temperature, pressure and humidity of purge gas, and is a strong factor in affecting product purity. It is possible to dry fluids to less than 0.1 ppm H2O, if adequately regenerated.

Shipping Information : Molecular Sieve 3A Grade is available in 150 Kg Air Tight Steel Drum Sealed with inner Liner (Polyethylene bags) for Extra Protection.

Molecular Sieve 13X AP Grade is an alkali alumino silicate. It is the sodium form of the molecular sieve type X and has an effective pore opening of about 9 angstroms (0.9 nm).

Typical Chemical Formula : Na₂O Al₂O₃ 2.5 SiO₂ nH₂O

Applications :Molecular Sieves13X AP Grade is commonly used for the following applications :

• Concurrent removal of H₂O and CO₂ from gas and air streams, removal of H₂S and mercaptans from liquids and hydrocarbon fractions, sweetening of natural gas containing H₂S, mercaptans & thiophenes, separation of heavy hydrocarbons from natural gas and air, separation of N₂  from O₂, catalyst bed protection; Static (non regenerative) removal of water and solvent vapours from the inner space of insulating glass units.
• Molecular Sieve 13X AP Grade will adsorb molecules with a kinetic diameter of less than 0.9 nm and exclude those larger.

Type :

• Standard 13X Grade
• Molecular Sieve 13X AP Grade is also available in powder form.

Regeneration : Molecular Sieve 13X AP Grade can be regenerated by evacuating or purging, usually at elevated temperatures. The purge gas temperature must be sufficiently high to bring the molecular sieve to a level of 200^oC to 300^oC, but not exceeding 600^oC. Higher temperatures may cause physical degradation of the molecular sieve structure. The degree of regeneration depends on the temperature, pressure and composition of the purge gas and is a strong factor in affecting product purity. It is possible to dry fluids to less than 0.1 ppm H₂O and purity to less than 1 ppm total sulphur and CO₂, if adequately regenerated.

Shipping Information : Molecular Sieve 13X AP Grade is available in 140 Kg Air Tight Steel Drum Sealed with inner Liner (Polyethylene) for Extra Protection.

Molecular Sieve 13X AP Grade is an alkali alumino silicate. It is the sodium form of the molecular sieve type X and has an effective pore opening of about 9 angstroms (0.9 nm).

Typical Chemical Formula : Na₂O Al₂O₃ 2.5 SiO₂ nH₂O

Applications :Molecular Sieves13X AP Grade is commonly used for the following applications :

• Concurrent removal of H₂O and CO2 from gas and air streams, removal of H₂S and mercaptans from liquids and hydrocarbon fractions, sweetening of natural gas containing H₂S, mercaptans & thiophenes, separation of heavy hydrocarbons from natural gas and air, separation of N₂ from O₂, catalyst bed protection; Static (non regenerative) removal of water and solvent vapours from the inner space of insulating glass units.
• Molecular Sieve 13X AP Grade will adsorb molecules with a kinetic diameter of less than 0.9 nm and exclude those larger.

Type :

• Standard 13X Grade
• Molecular Sieve 13X AP Grade is also available in powder form.

Regeneration : Molecular Sieve 13X AP Grade can be regenerated by evacuating or purging, usually at elevated temperatures. The purge gas temperature must be sufficiently high to bring the molecular sieve to a level of 200^oC to 300^oC, but not exceeding 600^oC. Higher temperatures may cause physical degradation of the molecular sieve structure. The degree of regeneration depends on the temperature, pressure and composition of the purge gas and is a strong factor in affecting product purity. It is possible to dry fluids to less than 0.1 ppm H₂O and purity to less than 1 ppm total sulphur and CO₂, if adequately regenerated.

Shipping Information : Molecular Sieve 13X AP Grade is available in 140 Kg Air Tight Steel Drum Sealed with inner Liner (Polyethylene) for Extra Protection.

You can rest assured us for the safest and superfast deliveries of the product range that we carry out in the dedicated time frame. We have streamlined inventory system and spacious warehouse that assist us in meeting the voluminous requirements of the clients and that too in the stipulated time span. With the latest facilities, we efficiently ensure year round availability of the products.

Molecular Sieve Sieve 3A is an alkali alumino silicate. It is the potassium form of the molecular sieve type A and has an effective pore opening of about 3 angstroms (0.3 nm).

Typical Chemical Formula : 0.45 K₂O – 0.55Na₂O Al₂O₃ -2SiO₂ - nH₂O

Applications :Molecular Sieves 3A is commonly used for the following applications :

• Static (non regenerative) removal of H₂O from air, organic vapour & gas like COS  filled insulating glass units and from solvents & fluids like 2-Propanol, Acetone, Acetonitrile, Acrylonitrile, Dimethyl Sulfoxide, Sulphur Hexafluoride, refrigerant gases etc
• Molecular Sieve 3A will adsorb molecules with a kinetic diameter of less than 0.3 nm and exclude those larger.

Type : 3A IG Grade is also available in Standard balls form.

Regeneration : Molecular Sieve 3A can be regenerated by evacuating or purging, usually at elevated temperatures. The purge gas temperature must be sufficiently high to bring the molecular sieve to a level of 1800C to 250^oC, but not exceeding 300^oC. Higher temperatures may cause physical degradation of the molecular sieve structure. When used to dry streams containing olefins, a purge at lower temperature is advised to prevent polymerization during regeneration. The degree of regeneration depends on the temperature, pressure and humidity of purge gas, and is a strong factor in affecting product purity. It is possible to dry fluids to less than 0.1 ppm H₂O, if adequately regenerated.

Shipping Information : Molecular Sieve 3A Grade is available in 150 Kg Air Tight Steel Drum Sealed with inner Liner (Polyethylene bags) for Extra Protection.

Molecular Sieve XH-7 is an alkali alumino silicate. It is the potassium form of the molecular sieve type A and has an effective pore opening of about 3 angstroms (0.3 nm).

Typical Chemical Formula : 0.45 K₂O – 0.55Na₂O Al₂O₃ -2SiO₂ - nH₂O

Applications in Refrigerants :

• Static (non regenerative) removal of H2O and volatile organic vapours from gas filled insulating glass units, Sulphur Hexafluoride and from refrigerant gases (having extensive use in refrigeration & air conditioning) especially R-134a (1, 1, 1, -Tetrafluoroethane) etc.
• Molecular Sieve XH-7 will adsorb molecules with a kinetic diameter of less than 0.3 nm and exclude those larger.

Type : Molecular Sieve XH-5, XH-9  Grade is also available on demand.

Shipping Information : Molecular Sieve XH-7 Grade is available in 160 Kg Air Tight Steel Drum Sealed with inner Liner (Polyethylene bags) for Extra Protection.

Activated Alumina The Best Available Technology : Granular Activated Alumina FR enables the removal of fluoride from drinking water and is used in industrial applications. Activated Alumina is one of the “Best Available Technology” for the removal of fluoride.

Industrial Applications : Fluoride content is a challenging health related concerns on the rise, our activated alumina offers a promising step for industrial waste waters. Common applications using fluoride within the production process include glass manufacturing, aluminium and steel processing, pesticide as well as fertilizer production and the semiconductor industry.

Cost Effective Treatment

• Activated alumina FR is a cost effective method for removing fluoride ion since it can be regenerated to allow the material to be used multiples of times before replacement is required.
• Granular Activated Alumina FR has a higher bulk density that also allows for more capacity over less dense aluminas.

Available Size

Granular Activated Alumina FR is available in the following granular sizes : 2 – 4 mm Granules

Shipping Information : Activated Alumina FR Grade is available in 25/50 Kg HDPE Bags.

Molecular Sieve Sieve 3A is an alkali alumino silicate. It is the potassium form of the molecular sieve type A and has an effective pore opening of about 3 angstroms (0.3 nm).
Typical Chemical Formula : 0.45 K₂O – 0.55Na₂O Al2O₃ -2SiO₂ - nH₂O

ApplicationsMolecular Sieves 3A is commonly used for the following applications :

• Drying of unsaturated hydrocarbons (such as ethylene, propylene & butadiene), cracked gas streams, natural gas where COS minimization is required, methane, ethane and of polar compounds such as methanol and ethanol, 2-Propanol, Acetone, Acetonitrile, Acrylonitrile, Dimethyl Sulfoxide.
• Static (non regenerative) removal of H2O and volatile organic vapours from gas filled insulating glass units, Sulphur Hexafluoride and from refrigerant gases
• Molecular Sieve 3A will adsorb molecules with a kinetic diameter of less than 0.3 nm and exclude those larger.

Type : Standard 3A Grade is also available in powder form.

Regeneration : Molecular Sieve 3A can be regenerated by evacuating or purging, usually at elevated temperatures. The purge gas temperature must be sufficiently high to bring the molecular sieve to a level of 1800C to 2500C, but not exceeding 3000C. Higher temperatures may cause physical degradation of the molecular sieve structure. When used to dry streams containing olefins, a purge at lower temperature is advised to prevent polymerization during regeneration. The degree of regeneration depends on the temperature, pressure and humidity of purge gas, and is a strong factor in affecting product purity. It is possible to dry fluids to less than 0.1 ppm H2O, if adequately regenerated.

Shipping Information : Molecular Sieve 3A Grade is available in 150 Kg Air Tight Steel Drum Sealed with inner Liner (Polyethylene bags) for Extra Protection.

Molecular Sieve 13X AP Grade is an alkali alumino silicate. It is the sodium form of the molecular sieve type X and has an effective pore opening of about 9 angstroms (0.9 nm).

Typical Chemical Formula : Na₂O Al₂O₃ 2.5 SiO₂ nH₂O

Applications :Molecular Sieves13X AP Grade is commonly used for the following applications :

• Concurrent removal of H₂O and CO₂ from gas and air streams, removal of H₂S and mercaptans from liquids and hydrocarbon fractions, sweetening of natural gas containing H₂S, mercaptans & thiophenes, separation of heavy hydrocarbons from natural gas and air, separation of N₂  from O₂, catalyst bed protection; Static (non regenerative) removal of water and solvent vapours from the inner space of insulating glass units.
• Molecular Sieve 13X AP Grade will adsorb molecules with a kinetic diameter of less than 0.9 nm and exclude those larger.

Type :

• Standard 13X Grade
• Molecular Sieve 13X AP Grade is also available in powder form.

Regeneration : Molecular Sieve 13X AP Grade can be regenerated by evacuating or purging, usually at elevated temperatures. The purge gas temperature must be sufficiently high to bring the molecular sieve to a level of 200^oC to 300^oC, but not exceeding 600^oC. Higher temperatures may cause physical degradation of the molecular sieve structure. The degree of regeneration depends on the temperature, pressure and composition of the purge gas and is a strong factor in affecting product purity. It is possible to dry fluids to less than 0.1 ppm H₂O and purity to less than 1 ppm total sulphur and CO₂, if adequately regenerated.

Shipping Information : Molecular Sieve 13X AP Grade is available in 140 Kg Air Tight Steel Drum Sealed with inner Liner (Polyethylene) for Extra Protection.

Molecular Sieve 13X AP Grade is an alkali alumino silicate. It is the sodium form of the molecular sieve type X and has an effective pore opening of about 9 angstroms (0.9 nm).

Typical Chemical Formula : Na₂O Al₂O₃ 2.5 SiO₂ nH₂O

Applications :Molecular Sieves13X AP Grade is commonly used for the following applications :

• Concurrent removal of H₂O and CO2 from gas and air streams, removal of H₂S and mercaptans from liquids and hydrocarbon fractions, sweetening of natural gas containing H₂S, mercaptans & thiophenes, separation of heavy hydrocarbons from natural gas and air, separation of N₂ from O₂, catalyst bed protection; Static (non regenerative) removal of water and solvent vapours from the inner space of insulating glass units.
• Molecular Sieve 13X AP Grade will adsorb molecules with a kinetic diameter of less than 0.9 nm and exclude those larger.

Type :

• Standard 13X Grade
• Molecular Sieve 13X AP Grade is also available in powder form.

Regeneration : Molecular Sieve 13X AP Grade can be regenerated by evacuating or purging, usually at elevated temperatures. The purge gas temperature must be sufficiently high to bring the molecular sieve to a level of 200^oC to 300^oC, but not exceeding 600^oC. Higher temperatures may cause physical degradation of the molecular sieve structure. The degree of regeneration depends on the temperature, pressure and composition of the purge gas and is a strong factor in affecting product purity. It is possible to dry fluids to less than 0.1 ppm H₂O and purity to less than 1 ppm total sulphur and CO₂, if adequately regenerated.

Shipping Information : Molecular Sieve 13X AP Grade is available in 140 Kg Air Tight Steel Drum Sealed with inner Liner (Polyethylene) for Extra Protection.

You can rest assured us for the safest and superfast deliveries of the product range that we carry out in the dedicated time frame. We have streamlined inventory system and spacious warehouse that assist us in meeting the voluminous requirements of the clients and that too in the stipulated time span. With the latest facilities, we efficiently ensure year round availability of the products.

Molecular Sieve Sieve 3A is an alkali alumino silicate. It is the potassium form of the molecular sieve type A and has an effective pore opening of about 3 angstroms (0.3 nm).

Typical Chemical Formula : 0.45 K₂O – 0.55Na₂O Al₂O₃ -2SiO₂ - nH₂O

Applications :Molecular Sieves 3A is commonly used for the following applications :

• Static (non regenerative) removal of H₂O from air, organic vapour & gas like COS  filled insulating glass units and from solvents & fluids like 2-Propanol, Acetone, Acetonitrile, Acrylonitrile, Dimethyl Sulfoxide, Sulphur Hexafluoride, refrigerant gases etc
• Molecular Sieve 3A will adsorb molecules with a kinetic diameter of less than 0.3 nm and exclude those larger.

Type : 3A IG Grade is also available in Standard balls form.

Regeneration : Molecular Sieve 3A can be regenerated by evacuating or purging, usually at elevated temperatures. The purge gas temperature must be sufficiently high to bring the molecular sieve to a level of 1800C to 250^oC, but not exceeding 300^oC. Higher temperatures may cause physical degradation of the molecular sieve structure. When used to dry streams containing olefins, a purge at lower temperature is advised to prevent polymerization during regeneration. The degree of regeneration depends on the temperature, pressure and humidity of purge gas, and is a strong factor in affecting product purity. It is possible to dry fluids to less than 0.1 ppm H₂O, if adequately regenerated.

Shipping Information : Molecular Sieve 3A Grade is available in 150 Kg Air Tight Steel Drum Sealed with inner Liner (Polyethylene bags) for Extra Protection.

Molecular Sieve XH-7 is an alkali alumino silicate. It is the potassium form of the molecular sieve type A and has an effective pore opening of about 3 angstroms (0.3 nm).

Typical Chemical Formula : 0.45 K₂O – 0.55Na₂O Al₂O₃ -2SiO₂ - nH₂O

Applications in Refrigerants :

• Static (non regenerative) removal of H2O and volatile organic vapours from gas filled insulating glass units, Sulphur Hexafluoride and from refrigerant gases (having extensive use in refrigeration & air conditioning) especially R-134a (1, 1, 1, -Tetrafluoroethane) etc.
• Molecular Sieve XH-7 will adsorb molecules with a kinetic diameter of less than 0.3 nm and exclude those larger.

Type : Molecular Sieve XH-5, XH-9  Grade is also available on demand.

Shipping Information : Molecular Sieve XH-7 Grade is available in 160 Kg Air Tight Steel Drum Sealed with inner Liner (Polyethylene bags) for Extra Protection.

Activated Alumina The Best Available Technology : Granular Activated Alumina FR enables the removal of fluoride from drinking water and is used in industrial applications. Activated Alumina is one of the “Best Available Technology” for the removal of fluoride.

Industrial Applications : Fluoride content is a challenging health related concerns on the rise, our activated alumina offers a promising step for industrial waste waters. Common applications using fluoride within the production process include glass manufacturing, aluminium and steel processing, pesticide as well as fertilizer production and the semiconductor industry.

Cost Effective Treatment

• Activated alumina FR is a cost effective method for removing fluoride ion since it can be regenerated to allow the material to be used multiples of times before replacement is required.
• Granular Activated Alumina FR has a higher bulk density that also allows for more capacity over less dense aluminas.

Available Size

Granular Activated Alumina FR is available in the following granular sizes : 2 – 4 mm Granules

Shipping Information : Activated Alumina FR Grade is available in 25/50 Kg HDPE Bags.