VIRSUN INDUSTRIES

Matsya Industrial Area, Alwar, Rajasthan

VIRSUN PLATINUM
Substrate: The surface to be covered with Ceramic tile shall be sound and confirm to good design, rigid, clean and free of dirt, oil, grease, curing compounds, form release agents or loose plaster and paint. For economy the surfaces should be level and true with in: Walls – 3mm in 2.5m Floors – 1.5mm in 1.0m Surface Preparation:
If a plaster/leveling mortar bed is applied, ensure that it is cured for at least 7 days to achieve proper strength before application of tile adhesive for installation of tile
Ensure the substrate is clean and free from impurities like dust, dirt, debris, oil, grease, curing agents, loose plaster etc
Dampen the wall before application of thin set adhesive
Clean the back of tile for any dust or coating
Mixing: The products can be mixed by hand or slow speed electric drill mixer (less than 300 rpm). Pour potable clean water in a clean container and then add the powder VIRSUN PLATINUM and mix until the mixture becomes creamy and plastic. Do not over mix. Leave the mix to slake for 5-10 min and remix before use. Mix only sufficient quantity of adhesive for immediate need. Proportion: Approximately 1 bag of VIRSUN PLATINUM  with 5-6 ltrs of water. Adjust quantity of liquid to obtain proper consistency. Installation:
Wet the surface and remove the excess water before applying the adhesive. Ensure the area is shaded from sunlight. The adhesive shall be applied with the flat side of the trowel using a scraping motion to work the material into good contact with the surface to be covered.
Additional mortar is then applied with the notched edge of the trowel.
When installing large tiles, spread adhesive onto back of tile in addition to trowelling material over surface to be tiled. Select proper type of notched trowel.
a) Thin Tiles upto size 300 X 300 mm (1’X1’), use a square notched trowel of size 6mm X 6mm to provide a total thickness of 3mm
b) Large Porcelain Tiles upto 450 X 450 mm with ribs, use a square notched trowel of size 6mm X 6mm and back butter the tiles with the same adhesive to a thickness of 1-1.5mm to provide a total thickness of 4.5mm
c) Large Porcelain Tiles upto 600 X 600 mm (2’X2’) with ribs, use a square notched trowel of size 6mm X 9mm and back butter the tiles with the same adhesive to a thickness of 1-1.5mm to provide a total thickness of 6mm
The most important standard to keep in mind is to insure that the piece of tile is completely bedded in the mortar or adhesive with 100% coverage.
Rear face of tiles (especially Porcelain tiles) should be cleaned with damp sponge to clean all the dust. Do not saturate in water.
Excess mortar on adhesive shall be cleaned from the surface of the stone with wet cloth or sponge while the mortar is fresh.
Coverage Approx. 55-60 sq. ft. per 20 kg bag with a ¼” x ¼” (6mmx6mm) square notch trowel for a bed of 3mm. Color Grey
Areas of Application Designed for internal floor applications   Suitable Substrates
Cement Mortar Beds
Cement Plaster
Brick Masonry
Cement Terrazzo
 

Virsun Apex Wall Adhesives BIS 15477 standard and en 1348 standard a high-performance dry adhesive for use with water or latex for installing ceramic tiles, marble and stone using the thin-set installation method. For use In floor and wall Installations, It has high track and will hang walltIlewIlhout slippage. the tiles can be made Degree, cotton, double fired, single fired ceramic. Fixing poorly absorbent materials or non-absorbent materials such as single-fired tel refine porcelain stoneware and vIltlflecitIles. Suitable for use when high performances are required, such as tile fixing In Industrial environment or Una on fop of old ceramic tiles or natural stone indoors in swimming pools or on facades.
Application Designed especially for interior & exterior door & wall installations of all types of tiles & stones.
Advantages
Dual use For both Floor & walls
Excellent non-sag formula
Smooth, easy to use
Improved impact resistance
Increased flexibility
Suitable Substrates
Extenor Grade Plywood (interior use only)
Cement mortar Bed/Plaster
Ceramic Tile & Stone
Ceramic Backer Board
Gypsum Wallboard (interior use only)
Concrete Masonry
Cement Terrazzo
Coverage Approx.55-60 sq.ft. per 20 kg bag using a 1/4"x1/4" (6mmx6mm) notch trowel for a bed of 3mm.
Color Grey & White
Weber Nova grey, myk 302 ultratech high strength stone adhesive

Advantages: 

• Easy to apply
• Water resistance
• Anti fungal
• Good compressive strength
• Good tensile strength
• Covers undulations of plastered surfaces

Virsun classic Floor Tile Adhesive is bis apoved isi standard is 15477:2019 type 1standrd en  1348 a bagged cementitious powder to be mixed with water for installing ceramic the and natural stone using the thin-set method of Installation. Tile adhesives are a factory prepared blend of carefully selected raw materials. Portland cement and graded aggregates (Latex) are added to adhesive powders to increase bond strength. Best suited for Exterior and Interior Installation of ceramic/ vitrified/ Porcelain/Engineered stones and Natural Stones. 
Applications
Best suited for Exterior and Interior installation of ceramic/ vitrified/ Porcelain /Engineered stones and Natural Stones.
Advantages
Single component, ready to use
Proven performance
High strength formula & ultimate flexibility
Ideal for external facades and underwater application
Suitable Substrates
Cernen1 Mortar Bed
Cement Plaster
Brick Masonry
CernentTerrazzo
Features
Single component, ready to use
Proven performance.

Tile Grout Admixstrong is a superior quality cementitious grout with hydrophobic properties that allow tile joints to resist water. Aqua Stick consists of the carefully prepared blend of Portland cement, chemical additives, and fillers. It is easy to install - just mix with water or Virsun Grout admix plus. Aqua Stick is ideal for floors and walls in both exterior and interior applications. For better performance, it is recommended to use Aqua Stick with VIRSUN Grout admix plus. Application Used for filling tile joints 1- 3mm in both interior and exterior areas, ceramic, vitrified, non-vitreous clay tile, natural stone and engineered stone/ agglomerates.

<p>To offer our purchasers top-notch range of products, we ensure only optimum grade supplies are utilized for their production. To protect our entire range of products from external factors that can be damaging, we have a state-of-the-art packaging unit equipped with the latest secure packaging technologies and materials.</p>

Advantages :

• Easy to apply
• Water resistance
• Anti fungal
• Good compressive strength
• Good tensile strength
• Covers undulations of plastered surfaces

Application :

• Designed for interior and exteriors surfaces.
• To make uneven surfaces to even and smooth surfaces.

Advantages :

• White cement based 2-in-1 Wall Putty
• White, smooth & glossy finish
• Protects paint from moisture
• Curing is not required
• Ideal for interior & exterior walls

Application :

• Clean & Pre wet the plaster surface before applying Stark Putty.
• Make a Stark Putty paste which can be used in 2 hours time.
• Apply the first coat of putty on pre wet surface from bottom to upward direction with putty blade.
• After drying of first coat of putty clean the surface with smooth dry cloth followed by wet cloth.
• Apply second coat of putty after about 3.0 hrs of first coat.
• Allow the surface to dry for minimum 12 hours.
• The Putty to be applied in two coats at a maximum thickness of 1.5 mm.
• During application of putty the surface should be protected from direct sunlight till the two coats of putty are dried.
• Designed for interior and exteriors surfaces.
• To make uneven surfaces to even and smooth surfaces

<p>Sun Tile Cleaner is a concentrate to be diluted with potable water as per need to clean all surfaces. It is non-toxic cleaner which can be used for daily maintenance as well as remove tough stains. This neutral pH cleaner makes it most suitable for cleaning marbles and other calcium-based stones. Sun Cleaners is also recommended for regular maintenance of sealed stone surfaces. It is effective and easy to use. <br /><br /><strong>Areas Of Application:</strong> Interior &amp; exterior areas Kitchens Floor &amp; Wall Bathrooms, Floor &amp; Wall Counter Tops Commercial floors. <br /><br /><strong>Use:</strong></p> <ul> <li>Mix 1 part of sun cleaners to 3 parts of hot water</li> <li>Apply over the stained area and scrub with the medium soft brush. Let it stay for 10-15 minutes and keep scrubbing periodically.</li> <li>Clean the surface with warm water for better results.</li> </ul> <p><br /><strong>For Regular Floor Cleaning</strong>: Dilute sun in the ratio of 1: 10 with clean water for a general day to day cleaning of the floor.<br /><strong><br />Cautions:</strong> Store in cool place away from heat and fire. Avoid contact with skin and eyes. Do not inhale and use it in open ventilated areas. Do not swallow and wear gloves during application.</p>