Vikas Instruments

Bara Bazar, Kolkata, West Bengal

MI 3299 HV DEMO BOX
The MI 3299 High voltage Demonstration Box 10 kV has been developed for demonstration purposes at high voltage insulation diagnostics. It simulates typical electrical insulation usually met in the industrial environment.

Features:

10 kV rated resistors with very low voltage coefficient.
Resistive decade with 200 k, 500 M, 200 G and 2 T resistors.
HV capacitors in 2.5 F and 5 nF range.
Built-in spark gap and gas discharge tube.
Demonstration of insulation breakdown in gases is possible.
Two models of insulation material (good and bad cables) enable the demonstration of real insulation behavior under high DC voltage.
Demonstration box is put in the strong rugged case with handle for comfortable carrying.

MI 2130 VOLTSCANNER
High performance, digital, one phase voltage recorder.

Features:

Pre-set voltage limits for power quality assessment in accordance with EN 50160.
Recording of power supply outages and transient over voltages.
Quick voltage quality assessment for unskilled users.
Optional: 110 V version.

MD 9210 CURRENT CLAMP

Versatility, sturdy case, high accuracy and lots of measurement functions are key features of the current clamp MD 9210. If you are looking for a universal current clamp offering good value for money, look no further!

Features:

DC and AC voltage up to 600 V
AC current measurement up to 600 A
Resistance measurement
Continuity test
Diode test
Frequency measurement
Capacitance measurement

Model:MI 2014

Cable Scanner is easy to use LAN tester with wide variety of functions for fault finding and troubleshooting on IT cabling connections.

Features:

TDR facility with adjustable NVP allows determination of distance to the fault or cable length measurement. Acoustic generator combined with a receiver enables pair determination in multi-pair cables.
Part of a standard set are locators for fast and simple numeration of LAN sockets.
Optional remote unit S 2004 for communication over the tested cable and shorten test time.
Connectivity supports UTP, STP, ScTP, FTP and coax cables.

The LCR203 are SMD component tweezers for use with Extech's LCR200 LCR meter. These tweezers make it easy to test and sort simultaneously for single handed operation. Tweezers complete the circuit with components easier than separate test leads. Comes with a 6 month warranty.

Features:

Cable length: approximately 22" (56cm)
Max component width: 0.75" (19mm)
Terminals: 3 banana plugs (High, Low, Guard)

The Extech 382275 power supply is an easy-to-configure, highly stable, lab grade DC power supply with maximum output power of 600 Watts. The new DC power supply offers two degrees of control over both current and voltage outputs (course and fine). Output is adjustable from 0 to 30 Volts DC and 0 to 20 Amps with (0.1 Volts/Amps resolution). Dual green LED displays offer easy-to-read, high contrast readouts of voltage and current values. The 382275 offers four operating modes: normal mode, with values controlled by front-panel knobs; preset mode, which offers three popular voltage presets at 20 Amps: 5.0 Volts, 13.8 Volts, and 25 Volts; set mode, with three user-customizable presets; and remote control mode, where the user can remotely adjust output power on/off, voltage and current. Other features include automatic constant current and voltage, high RFI immunity, excellent EMI, a thermostat-controlled variable speed fan, as well as over-voltage, over-temperature, and short circuit protection. The 382275 offers a compact, low profile design and small footprint without compromising output noise and transient response factors. Complete with power cord.

Features:

Remote Control for output Voltage/Current and On/Off
Two user-defined Voltage and Current presets and one 13.8V/20A factory preset
Automatic Constant Current crossover
Dual 3-Digit LED displays
High RFI immunity and excellent EMI
Thermostatic Control Fan from zero to full speed
Overload, over-temperature, and short circuit protection

The 382254 are a replacement set of Test Leads for Extech's Model 382252 Earth Ground Resistance Tester Kit. The 382254 are color coded, durable test leads. Comes with a 6 month warranty. Five piece test lead set.

Features:

Compatible with 382252 - Earth Ground Resistance Tester Kit

The 382253 are Earth Bars for Extech's Model 382252 Earth Ground Resistance Tester. Use as replacements or spare bars. The 382253 earth bars are durable, light weight and come in a pack of two. Comes with a 6 Month warranty.

Features:

Compatible with 382252 - Earth Ground Resistance Tester Kit

The 40180 is a Tone Generator and Amplifier Probe Kit. This heavy-duty kit with audible tone easily identifies wires or cables. The insulated inductive probe tip prevents shorting conductors. Featuring a wire trace, continuity test, clear/busy/ringing line test, and tip/ring identification. Includes Alligator clips, RJ45 and RJ11 modular connectors, 9V battery and Case.

Features:

Insulated inductive probe tip prevents shorting conductors
Tests include wire trace, continuity test, clear/busy/ringing line test and tip/ring identification
Alligator clips for non-terminated cables and modular connectors for direct connections to telephone and internet wiring
Selectable continuous or variable tone generation
Built-in speaker on probe with sensitivity control

Video Borescope Inspection Camera with 17mm camera diameter and 2.4 inch color TFT LCD Monitor is ideal for Home Inspection (Inspect in walls for mold, insect infestation, electrical wire or water pipe location); HVAC ( Inspect inside ducts, behind motors and compressors); Automotive (View inside or around engines and transmissions); Industrial (Inspect weld integrity, process equipment, gears, molding machines); Aerospace (Aircraft inspections for contamination, debris, cracks or other damage), and Government (Safety and security inspections) Applications. Glare-free close-up field of view. Display detaches for easy storage. Complete with 4 x AA batteries, extension tools (mirror, hook, magnet), video output jack, and hard case.

Features:

17mm diameter camera head with 39" (1m) flexible gooseneck cable retains configured shape
Mini water-proof (IP67) camera head for high resolution viewing
Two bright LED lamps with dimmer to illuminate viewed object
Glare-free close-up field of view
Display detaches for easy storage
Optional BR200-EXT extension cable available for increasing viewing depth (maximum 2 extension cables can be connected to the borescope)
Complete with 4 AA batteries, extension tools (mirror, hook, magnet), video output jack, and hard case

The 461950 is a 1/8 DIN Panel Tachometer. Measure rotational motor speed, moving fans, pumps, gears, propeller devices. Choice of 2 sensor pickup types: Proximity sensor-0.1 in. (3 mm) target distance, range up to 36, 000rpm (600Hz); Photoelectric sensor-0.4 in. (10 mm) target distance, range up to 6, 000rpm (1kHz). 1/8 DIN size. Powered by 115/230VAC 50/60Hz.

Features:

Measure rpm from 5 to 99, 990rpm with microprocessor quartz crystal accuracy of 0.05%
Large LED display updates 1/sec (rpm

SC600 is an Electronic Counting Scale/Balance with Load Cell Transducer. This scale is for professional electronic counting and weighing with load cell transducer for high accuracy and performance. Wide capacity measuring single small electronic component weighing 0.005oz (0.1g) or batches up to 21.164oz (600g). Optional software available for generating reports and documentation of inventory components. Complete with 6 AA batteries, metal platform, and Universal AC adaptor with multi-plugs.

Features:

Wide measuring capacity up to 600g (21.164oz)
Gram or Ounce measurement selectable by internal slide switch
0.05% accuracy with 0.01g and 0.0005oz resolution
LCD display with 0.8" (20.9mm) easy-to-read digits
Built-in self-calibration system using traceable weights
High precision counting function with preset counting sampling number selection of 10pcs, 20pcs, 50pcs, or 100pcs
Built-in bubble level with adjustable rubber pads and RS-232 interface
Complete with 6 AA batteries, metal platform, and Universal AC adaptor with multi-plugs

Ideal for a wide range of applications including bench testing, field service, hobby and telecommunication equipment, the solid state, compact Extech 382213 digital DC power supply delivers clean, reliable power while protecting itself and any device under test (DUT) from damage. It offers three choices of power output: adjustable 0-30-Volt, 0-3-Amp, plus fixed 5- and 12-Volt. Featuring a digital LCD display, the 382213 also includes overload and short circuit protection, constant voltage/current, easy snap terminals for 5- and 12-Volt outputs, and a current-limited front panel LED indicator. Complete with power cord.

Features:

Adjustable Voltage and Current output
Easy snap terminals for fixed 5V/0.5A and 12V/1A outputs
Constant Voltage or Current
Current limiting indicator
Overload and short circuit protection
Binding post terminals for variable supply

382270 is a Quad Output DC Power Supply has two 0 to 30V/0 to 5A outputs plus two fixed auxiliary outputs of 3 to 6.5V/3A and 15V/1A. The two 30V outputs can be combined in parallel for 10A or in series for 60V. Comes complete with 4 pairs of test leads (banana plug to alligator clip) and an AC cord.

Features:

Two fully adjustable supplies combined with two auxiliary outputs
Two 0 to 30V/0 to 5A outputs with selectable Constant Voltage and Constant Current modes
Two auxiliary outputs with fixed current of 3 to 6.5V/3A and 8 to 15V/1A

Transformer Testing Panel
TRMS Voltage 600V /1200V Phase, 1050V / 2100V Line

TRMS Current 80A / 160A Direct
USB , RS-232 / RS-485 interface & Free Software
20 X 4 LCD Display & Ultra Glow Red LED Display
High Speed Measurement in 0.25Sec (Optional)
Tamper Proof Calibration & Long term stability
User Friendly Operation
NABL certified in EQDC & ERDA

Features:

TEST TO BE CONDUCT
No load Test
Load Test (Short Circuit Test)
DVDF Test
HV Test

Scope of Measurement
Voltage (V), Current (I), Power (P), Power Factor (PF), Apparent Power (VA), Reactive Power (VAR), Mean Voltage (Vmean), Peak Voltage (Vpeak), Rectified Voltage (Vrect), Mean Current (Imean), Peak Current (Ipeak), Rectified Current (Irect), Crest Factor (cf), Form Factor (ff), Frequency (F) etc.

Measures the concentration of dissolved salt in fluids. Compact size, easy to operate. Automatic Temperature Compensation (ATC) from 10 to 30C. Comes with case, calibration screwdriver, plastic pipette calibration solution, and user guide.

Features:

Compact size, easy to operate
Automatic Temperature Compensation (ATC) from 10 to 30C
Provides accurate and repeatable measurements on easy to read scale
Requires only 2 or 3 drops of solution
The prism and lens with a simple focus adjustment
Complete with case, calibration screwdriver, plastic pipette and calibration solution

The HDV600 has various optional camera probes to fit your application needs. Choose from a range of sizes with articulating and/or wireless features. Waterproof (IP67) Videoscope features a 5.7 in. color LCD TFT with high definition 640 x 480 resolution. The SD memory card included stores more than 14, 600 images. Video recording (up to 4 hours) with voice annotation. AV output for viewing images and video directly on a monitor. Video and images can be transferred to a PC via the SD card or USB output. Optional wireless transmitter allows you to transmit video up to 100ft (30 m) from the measurement point to your monitor. Includes SD card, 3.7 Volt rechargeable Li-Polymer battery, patch cable, AC adaptor, USB and AV cables, and hard carrying case.

The Extech's HDV650-10G Plumbing Videoscope Kit unveils problems with its large, waterproof, rugged, high definition color display and a 10 meter snake probe with 25 mm diameter camera head. The Extech HDV65010G has a built-in bright lights which help illuminate the problem area deep within the pipelines. The camera probe is rugged enough to dislodge small clogs. The Extech HDV650 10G is ideal for inspecting P-traps, 90s, drains, pipeline runs, and more. Complete with VideoScope, 25mm camera probe, SD card, 3.7V rechargeable battery, patch cable, AC adapter (110-240V, four plugs), USB and AV cables, and hard carrying case.

Features:

Includes flexible, fiberglass core, 10m waterproof camera probe (spool assembly)
25mm camera head (60 FOV, long depth of field) with built-in bright 12 LEDs for illuminating the problem areas
5.7" color LCD TFT with high definition 640 x 480 VGA pixel resolution
Rugged oil/chemical resistant and water/drop proof housing (IP67)
Non-slip ergonomic handles for ambidextrous use
SD memory card included to store >15, 000 images
Video recording (up to 4 hours) with Voice annotation
AV output for viewing images and video directly on a monitor
Video and images can be transferred to a PC via the SD card (included) or USB output
Complete with VideoScope, 25mm camera probe, SD card, 3.7V rechargeable battery, patch cable, AC adapter (110-240V, four plugs), USB and AV cables, and hard carrying case

Model :UT256

UT256 series is an AC/DC fork meter with high reliability, high security, auto-range, and mini shape. Its appearance adopts creative design so that wires to be tested can be stuck by the jaw directly instead of after the jaw is pressed to open.

Features:

It can measure AC/DC current provided with true RMS function. Flashlight on the meter is specially designed for smooth measurement under darkness. Full-range overload protection and distinctive appearance design make it be a new-generation practical electrical measuring meter with better performance.

Model :UT261A/UT261B

UT261 series has a large LCD screen. UT261A can test 40690V AC voltages. It can test 600V voltage for 30 minutes constantly with full-phase connecting indication, missing phase indication. UT261A is powered by the circuit to be tested.

Features:

It can withstand impact of dropping from 2 meters height. Test leads with protective tube are included in optional accessories. It conforms to IEC61557 European Standard.

The Extech 461830 is a digital StroboTach tachometer. Freeze motion and analyze rotating objects without contact. Checks and analyzes motion and speed by simply aiming and synchronizing its flash rate (FPM) with a rotating object. Ideal for measuring the speed of moving gears, fans, pumps, motors and other equipment used in general maintenance, production, quality control, or laboratories. Complete with 6 ft power cord, handle and can be tripod mounted.

Features:

Checks and analyzes motion and speed by simply aiming and synchronizing its flash rate (fpm) with a rotating object
RPMs on 4 digit LED display
High accuracy over a wide, dynamic range via exclusive microcomputer LSI circuit and crystal control time-base
Ideal for measuring the speed of moving gears, fans, pumps, motors and other equipment
Tripod mount for stationary use

The TG20 Wire Tracer Kit identifies wire pairs, check continuity and test telephone line polarity. Transmitter has output cables terminated in modular RJ11 phone connector. The non-contact amplifier probe audibly identifies the selected wire or cable so that you can easily trace from source to termination. Comes complete with Wire Tracer Probe and Transmitter with RJ11 phone connector, a pair of alligator clips and two 9V batteries.

Features:

Transmitter with output cables terminated in modular RJ11 phone connector
Transmitter injects traceable signal into cables, checks telephone lines, and performs continuity checks
Non-Contact probe audibly identifies selected wire or cable
Easily trace wires from source to termination
Test for properly operating phone lines
Adjustable sensitivity control improves wire identification and eliminates false detection
Continuity test ? visible indication
Complete with Wire Tracer Probe and Transmitter with RJ11 phone connector and pair of alligator clips, and two 9V batteries

Laser Switch
Auto Power Off
Low Battery Indication
Backlight Display
MAX Function
MIN Function
LCD size 30 x 31mm

Models : IRT550P

Laser Switch
Auto Power Off
Low Battery Indication
Backlight Display
MAX Function
MIN Function

Models : IRT1050P

Laser Switch
Auto Power Off
Low Battery Indication
Backlight Display
MAX Function
MIN Function
DIG Function
AVG Function
Data Storage
High / Low Temperature Alarm Settings Functions

Functions MAX / MIN / HOLD, Auto Power Off
Range 35 dB 130 dB (31.5 Hz 8 kHz)
Accuracy 1.5 dB ( under reference condition) Resolution 0.1 dB
Power 9 V Battery

Models : 920P Humidity & Temperature Meter

C / F / RH Selection MAX / MIN
Auto Power Off
Range 0% 100%
RH Accuracy +/- 3% RH (25C, 20 80% RH) +/- 3.5% RH (At Other Ranges)
Resolution 0.01C / 0.01F

Models : 961P Air Flow Anemometer

Functions m / Sec, Ft / min, Knots, Km / h, MPH, CFM, MAX / MIN / HOLD
Auto Power Off Range 1 25 m /s
Accuracy +/- (3% rdg +/- 0.2 m /s)
Resolution 0.01 m / s

Models : 930P Digital LUX Meter

Functions MAX / MIN, Backlight
Auto Power Off Range 0 200, 000 lux 0 20, 000 fc Accuracy +/- 5% rdg + 10 dgt (< 10.000 lux / fc) +/-10% rdg + 10 dgt (>10.000 lux / fc)
Resolution 0.1 lux or 0.1 fc Selection lux / fc

the motwane make primary injection kit (mot-pik) has different models with range of output currents from 100a to 3000a.these are well protected with the provision of mcb against overload than the rated current. Hrc fuse protection is provided for control circuits. Bright led indicators are provided for indicating input /output status. The pik comes with adequate cooling systems like air/oil cooling depending upon the ratings. It is having one knob control to vary output current. The pik can be utilized for high current injections during commissioning of protection systems, testing after major repairs / equipment replacements in power sub stations.

features:

single compact unit equipment for easy operation

designed to offer continuously variable output current

built in digital timer for measuring tripping time

adequate mcb protection from overloads

customization as per customers requirements.

digital meters for display of voltage & current

digital time interval meter range from 0.0001 sec to 9999 sec

burden capacity from 1 kva to 20kva **

current range from 100a to 3000a **

features:

single compact unit equipment for easy operation

designed to offer continuously variable output current

built in digital timer for measuring tripping time

adequate mcb protection from overloads

customization as per customers requirements.

digital meters for display of voltage & current

digital time interval meter range from 0.0001 sec to 9999 sec

burden capacity from 1 kva to 20kva **

current range from 100a to 3000a **

Model:TG54 & TG56
The FLIR TG54 and TG56 Spot IR (Infrared) Thermometers provide non-contact surface temperature readings so you can quickly and easily take measurements in places that are out of reach. Providing a distance-to-spot ratio of up to 30:1, the TG54 and TG56 can measure smaller targets from a safer distance. New mode options give you control to view your current reading and last two temperature readings simultaneously. The TG54 and TG56 are built with a color screen that makes it easy to navigate and select settings, plus adds visibility and efficiency to the advanced feature set. The TG54 and TG56 are your go-to, pocket-sized devices for efficient temperature measurement.

Features:

Measure smaller targets from a safer distance
Take non-contact measurements in hard-to-reach spots up to 30:1 distance-to-spot ratio

Easily pinpoint what is hot or cold
Built-in laser targeting helps you easily identify measurement location

Work easily through poor lighting conditions
Powerful LED worklight guides you to your target in poor lighting conditions

Simple to use, easy-to-navigate
Graphical menu structure and color display enable easy access to measurement settings and alarms, and you can view your current reading and last two readings together on one screen

Convenient and rugged design
Durable, industrial design that can withstand a three-meter drop, with a tool-less battery compartment

Thermocouple probe input for measurement flexibility (TG56 only)
View your type K thermocouple temperature measurement, your IR thermometer measurement and the difference between the two on one screen when the thermocouple is inserted.

This HW30 multi-function stopwatch displays a digital up/down timer, temperature, humidity and heat index. The heat index measurement shows how hot it feels when humidity is combined with the actual temperature. Ideal for use in hot weather conditions. Additional features include a 12/24-hour clock, stopwatch, 30 lap/split memory and programmable alarm. HW30 Humidity/Temperature HeatWatch comes with lanyard, battery, and operating instructions.

Features:

User adjustable Heat Index alarm
Stopwatch/chronograph mode with 1/100 second resolution
Fastest/Slowest/Average Lap recall
99 lap counter with 30 lap/split memory
10 hour countdown timer with audible beeper warning for the last 5 seconds
Programmable alarm
Calendar mode displays day, month, and date

The MOTWANE make secondary injection kit (MOT-SIK) has different models with range of output currents from 25A to 100A. HRC fuse protection is provided for over loads & control circuits. Bright LED indicators are provided for indicating input /output status. The SIK comes with adequate air cooling systems. It is having one knob control to select the output current. Separate knob provided for coarse control. The SIK is generally called as Relay test set when used for testing of relays .This can be utilized for current injections during commissioning of protection Relay systems, testing of equipments like Ammeters, voltmeters , transducers, energy meters in power sub stations.25A with 3ph AC output with provision of DC output model is also available.

Features:

Single compact unit equipment for easy operation

Designed to offer continuously variable & selectable output current

Built in Digital Timer for measuring tripping time

Adequate fuse protection from overloads

Customization as per customers requirements.

Digital meters for display of AC& DC voltage & AC current

Digital time interval meter range from 0.0001sec to 9999sec

Burden capacity from 200VA to 600VA ** Current range from 25A to 100A

The CT40 enables one person to identify up to 16 local or installed lines. The built-in MultiMeter functions include: AC/DC Voltage and Current, Resistance, Diode, and Continuity for troubleshooting electrical/electronic circuits. Additional features are Data Hold and Max Hold, Auto Power Off and a low battery indicator on both the Transmitter and Receiver. CAT II-600 Volt safety rating. Comes complete with two 9 Volts batteries, 2 AAA batteries and a pouch case.

Features:

Troubleshoot electrical/electronic circuits and identify up to 16 local or installed lines
MultiMeter functions include: AC/DC Voltage and Current, Resistance, Diode, and Continuity
Transmitter/Receiver enables one person to remotely identify up to 16 wires
Wire voltage check from 5 to 16VDC
Data Hold and Max Hold, Auto power off
Low battery indicator (transmitter and receiver)
Complete with 16-line Transmitter, MultiMeter/Receiver, two 9V batteries, pouch case, and 2 AAA batteries

Exec's PD20 is a pocket-sized pedometer which offers 3D Sensor design for detecting motion regardless of orientation, as well as Temperature measurements! The fully loaded PD20 has many other functions including a Step Counter, Timer, Distance meter, Speedometer, Calorie Counter, Fat-Burning meter and Storage Memory. Complete with CR2032 battery, belt-clip and nylon case with window opening for display viewing.

Features:

3D motion sensor design allows for the meter to be fully functional regardless of its orientation
Uses an intelligent algorithm to filter out non-walking movements
Functions:
Number of Steps: 0 to 99999 (adjustable step length)
Temperature: 14 to 122F (-10 to 50C)
Calorie consumption: 0 to 99999kcal
Fat burned: 0 to 35.9oz (0 to 999.9g)
Distance covered: 0 to 624.99mi (0 to 999.99 km)
Time: 12/24 hour format
Average speed: 0 to 6.25mph (0 to 10km/h)

The IRT600 is a Dual Laser IR Thermal Condensation Scanner. This 12:1 Infrared Psychrometer with 3-Color LED Dew Point Alarm measures temperature and humidity then calculates Dew Point and warns the user when conditions for mold growth exist. Great for processes that require surface temperature control and monitoring. Green LED changes to Yellow and then to Red as the surface temperature reading gets closer to and then equals the calculated Dew Point reading. Dual lasers indicate ideal measuring distance where the two lasers converge to a 1" target spot. Complete with case and 9V battery.

Features:

Measurement range: -22 to 662F (-30 to 350C)
Great for processes that require surface temperature control and monitoring
Green LED changes to Yellow and then to Red as the surface temperature reading gets closer to and then equals the calculated Dew Point reading
A dual laser system for easy targeting
150 millisecond IR Temperature response time
Switchable backlight and laser, Max Hold
Complete with case and 9V battery

In Electrical System, sometime without identification of Phase Sequence it is impossibleto proceed further. The Phase Sequence Indicator is used to determine the Phase Sequence R, Y & B of 3 Phase Voltage. It is important that Phase Sequence is known properly prior to energizing electrical motor & other equipment, as incorrect connection could cause damage to the equipment. The correct operation of measuring instrument like 3 Phase Energy Meter, 3 Phase Power Meter and Automatic Control of devices also depend on the Phase Sequence.

Features:

3 Phase Sequence Indication via LED & Buzzer
Reverse Phase Indication via LED & Buzzer
Open Phase Indication via LED & Buzzer
No Battery Required
Rugged & Handy
Easy & Safe to Use
Coloured Test Probes with Heavy Duty Insulated Crocodile Clips for R, Y, B Phase Connections
Phase Presence Indication from as low as 60 V AC (PH-N)

I-V curve test for solar system
Max. solar system power (Pmax) search by Auto-scan: 1000V, 12A (12000W capability)
The analyzer and the Remote Solar Detector is connected by Bluetooth wireless communication (Bluetooth 2.1 + EDR Class 1)
The Remote Solar Detector is moisture-proof
Intelligent test logic with no personnel attendance required in the field
Solar system analyzer waits and tests the system until appropriate sunlight irradiance is detected
Max. voltage (Vpm) at Pmax, Max. current (Ipm) at Pmax
Voltage at open circuit (Voc), Current at short circuit (Isc)
Efficiency (%) calculation of solar system
Temperature measurement of solar panels
Irradiance measurement of sun light
Series resistance (Rs) calculation of solar panels
With data logging/open function, the I-V curves of solar system can be analysed / recorded for a period of time (e.g. 60 min.)
Conversion of I-V curve under OPC to data under standard test condition (STC) based upon IEC standard
Provide Operating Condition (OPC) and Standard Test Condition (STC) test reports for verification of solar panel performance (OK or NO OK)
Users can set up the parameters of solar panels

Features:

Users can set up the series number of solar panels. Parameters of many solar panels can be measured in one measurement
The Irradiances and Temperatures of solar panels can be continuously measured, monitored and recorded
Continuously measure/monitor/record the DC power output of solar system and the AC power output of inverter (1 phase or balanced 3 phases)
Calculate the efficiency of DC to AC power conversion and the efficiency of the max.output power
Built - in Calender Clock
Rechargable Lithium Battery, Low Battery Warning, AC Power Adaptor
Optical USB Cable for PC Communication
Solar Connector (optional)
With Power Clamps (SOLAR 15 DC Current Probe and SOLAR 21 AC Power Clamp), continuously measure / monitor / record the DC AC Power output of Solar System and the AC Power Output of Inverter (1 phase or balanced 3 phases); calculate the Efficiency of DC to AC Power Conversion and the Efficiency of the max.output power.

MECO FCT is a Flexible Current Transformer based on the Rogowski principle. It is suitable to conveniently measure Single / Three Phase AC and Pulsed DC Current. After approximate signal conditioning, it can be used with Digital Multimeter, Recorders and other suitable equipment to measure current from very low frequencies upto 1 MHz.

Features:

The probes comprises of a flexible air-cored sensor which can be opened and installed around a primary conductor without interrupting the circuit. The flexible and lightweight measuring head allows quick and easy installation in hard to reach areas and over large conductors. Inner Diameter / Window size and leads can be customized.

Low Cost
Low profile for PCB Mounting
High Accuracy
Wide Linear Range
Low Phase Shift Error
Flame Retardant
Nano Crystalline / Permalloy Core

Features:

Accuracy : Class : 0.1
Dielectric Strength : 2.5KV at 50Hz for 1 min
Dielectric Resistance : 100M Ohms @ 500V DC
Working Frequency : 50 - 400Hz
CE Approved & RoHS Compliance
Customer Specification Are available

Clamp - On Design, Fastening Safe, Easy to Install, Portable.
Wide Inner Window, Allowing Clamping of Big Cables or Bus - Bar
Frequency : 50 - 400 Hz

Features:

Current Measurement, Monitoring and Protection for Electrical Wiring and Equipment, Current and Power Measurement for Electric Motors, Lighting, Air Compressor, Heating and Ventilation System, Air - Condition Equipment and Automation - Control System, Current, Power and Energy Monitoring Device, Relay Protection Device

The VIR50 is a 3992F (2200C) Digital Laser Video IR Thermometer which features a 2.2" color TFT LCD display and built-in VGA (640 x 480) Camera. Includes a MicroSD card for capturing images (JPEG) and video (3GP) for viewing on your PC. Dual lasers indicate the ideal measuring distance (approximately 50 inches) where the two laser points converge to a 1" target spot. Comes with microSD card, general-purpose Type K bead wire probe, USB cable, rechargeable 3.7V battery, carrying case, and user manual.

Features:

Non-contact IR Temperature measurement from -58 to 3992F (-50 to 2200C) with 50:1 distance to target ratio
Built-in VGA (640 x 480) Camera
MicroSD card for capturing images (JPEG) and video (3GP) for viewing on your PC
Dual laser indicates ideal measuring distance where the two laser points converge to a 1" target spot
Fast 150 millisecond response time, color LED bargraph for viewing trends
Type K Thermocouple input, USB interface
Air Temperature and Relative Humidity measurement
Adjustable emissivity increases measurement accuracy for different surfaces
Adjustable High/Low set points with audible alarm alerts user when temperature exceeds the programmed set points
MAX/MIN/AVG/DIF functions, Auto Power Off
Complete with microSD card, general purpose Type K bead wire probe, USB cable, rechargeable 3.7V battery, and carrying case

Extech's MS420 20 MHz 2-Channel Digital Oscilloscope offers a range of capabilities for effective troubleshooting of electronics and electronically controlled electrical systems. With 20 MHz bandwidth and conveniences like auto-set which optimizes the position, range, time base, and triggering to assure a stable display of virtually any waveform, the MS420 can be used in field repairs or bench duty. To identify subtle problems, Peak Detect features a fast 50 ns glitch capture. Core functions like XY Mode, FFT function, Trigger Hold off, Waveform Math, Averaging Mode and Persistence Mode all ensure you can confidently troubleshoot problems using a variety of approaches. To start up recurring testing routines, you can store and recall up to 4 waveform screens and setups to save time from job to job. This CAT II-rated oscilloscope extends its functionality with complete DMM functions that are displayed on the large 3. 8" (97mm) color LCD display. The MS420 comes with two 1X/10X oscilloscope probes, test leads, Windows XP/Vista compatible USB software and cable, capacitor measuring module, adjustment screwdriver, AC adaptor/charger, hard carrying case, user manual, and manufacturer's one-year limited warranty.

Features:

Auto-set function optimizes the position, range, timebase, and triggering to assure a stable display of waveforms
Peak Detect function for 50ns glitch capture
XY Mode and FFT function to view component frequencies
Twenty Automatic Measurements including Frequency, Cycle, Average, Peak to Peak, RMS and more
Waveform Math: Add, Subtract, Multiply, and Divide
Average Mode for smoothing waveforms
Persistence Mode for observing dynamic signals
Store and recall up to 4 waveform screens and setups
USB interface and software for transferring waveforms and data

C outlet load handling capabilities plus Outlet Tester functions
Circuit and wiring issues can introduce shock hazards (from grounding issues) and can compromise performance of machinery and equipment (from poor ground impedance, lack of sufficient voltage under load and/or high ground-to-neutral voltage). The CT70 is a GFCI and AC Circuit Analyzer which covers outlet load handling and outlet tester functions. Complete with AC test cord (standard North American 3-prong plug).

Features:

AC Load Tester functions:
Selectable loads of 12 15 and 20 Amps
Measures loaded and unloaded AC Line Voltage
Calculates and displays % Voltage Drop and Line Impedance
Displays Peak Line Voltage and Frequency

Model. : Fluke 500 Series

Reduced testing complexity, a simplified workflow and an intuitive user interface provide a new level of ease-of-use in battery testing.
The ideal test tool for maintenance, troubleshooting and performance testing of individual stationary batteries and battery banks used in critical battery back-up applications
The intuitive user interface, compact design and rugged construction ensure optimum performance, test results and reliability
Covers a broad range of battery test functions ranging from DC voltage and resistance tests to full condition testing using automated string function testing and the test probe integrated infra-red temperature measurement system
Designed for measurements on stationary batteries of all types.

Features:

Fluke BT510 key features:
Battery Voltage - During the internal resistance test, Fluke Battery Analyzers also measure the voltage of the battery under test
Discharge Volts - The Discharge mode collects the voltage of each battery multiple times at a user defined interval during a discharge or load test. Users can calculate the time a battery takes to drop to the cut-off voltage and use this time to determine the capacity loss of the battery
Ripple Voltage Test - Measures unwanted residual ac component of the rectified voltage in dc charging and inverter circuits. Allows users to test ac components in dc charging circuits and find one of the root causes of battery deterioration
Meter and Sequence Modes - The Meter mode is used for a quick test or troubleshooting. In this mode you can save and read the readings in a measurement or time sequence. The Sequence mode is for maintenance tasks with multiple power systems and battery strings. Before a task starts, users can configure a profile for the task for data management and report generation
Threshold and Warning - Users can configure a maximum of 10 sets of thresholds and receive a Pass/ Warning/ Fail indication after each measurement
Intercell Strap Resistance Test and Data Management - Measures the resistance of the intercell connection between batteries in a string. Once the measurements are completed Fluke Battery Management Software version 1.0.69 can now report the strap resistance for a battery string or historical data over time.
AutoHold - When AutoHold is turned on, a reading is captured when it remains stable for 1 second. The reading is then released when a new measurement starts
AutoSave - When AutoSave is turned on, measured values are saved to internal memory automatically after an AutoHold reading is captured
Fluke Battery Management Software - Easily import data from the Product to a PC. The measurement data and battery profile information is stored and archived with the Management Software and can be used for comparison and trend analysis. All measurement data, battery profile and analysis information can be used to easily generate reports
Comprehensive logging - All measured values are automatically captured during testing and can be reviewed on the instrument before downloading for on the-go analysis
Optimized user interface - Quick, guided setup ensures you're capturing the right data every time
Battery life - 7.4 V 3000 mAh lithium-ion battery for more than eight hours continuous operation.
USB port - For fast data download to supplied data analysis and report management application software.
Highest safety rating in the industry - CAT III 600 V, 1000 V dc max. rated for safe measurements all around the battery power supply equipment.
Fluke BT520 key features: (Designed for measuring batteries in cabinets and hard to reach places)
All of the above plus
BTL20 Interactive Test Probe set, with long and short probe extenders and built-in LCD display and speaker for visual and audio feedback
Large soft carry case
Fluke BT521 key features: (Designed for users who need to incorporate temperature measuring)
All of the above1 plus
BTL21 Intelligent Test Probes with long and short extenders, built-in LCD display and speaker for visual and audio feedback and integrated infrared temperature sensor for taking temperature measurements on the negative battery post with every test
Wireless capability works with Fluke Battery Analyze mobile app (Fluke BA Mobile)2
View profile and associated test results from the Battery Analyzer

Stakeless earth ground loop and ac leakage current clamp for fast, safe indoor/outdoor earth ground resistance and ac leakage current tests.

Features:

Test the grounding components of equipment in hard-to-reach spaces, including areas that are indoors or fully paved and do not permit driving auxiliary test stakes. Stay on lineidentify ground loop resistance without the need to disconnect then reconnect the earth electrode from the system.
The Fluke 1630-2 FC Stakeless Earth Ground Clamp is the kind of high-quality, rugged tool you expect from Fluke. Heavy-duty clamp jaw stays in alignment and in calibration even in every day, on-the-job industrial environments.
Stakeless measurement
The 1630-2 FC clamp measures earth ground loop resistances for multi-grounded systems using the dual-clamp jaw. This test technique eliminates the dangerous and time-consuming activity of disconnecting parallel grounds, as well as the process of finding suitable locations for auxiliary test stakes. You can also perform ground tests in places that were previously difficult: inside buildings, on power pylons or anywhere you dont have access to soil to place auxiliary test stakes.

The RD300 Refrigerant Leakage Detector detects leakages from air-conditioning units and cooling systems. It's easy to use and is ideal for detecting leakages from air-conditioning units and cooling systems that use all standard refrigerants. The multi-colored LED light bar indicates the level of leaking refrigerant detected by the RD300. The built-in, bright LED convenience light located at the sensor tip illuminates dimly lit inspection areas. Complete with leak test bottle, 9V battery, and protective hard carrying case.

Features:

Detects all standard refrigerants using a heated diode sensor
LED light at probe tip (with on/off switch) for working in dimly lit areas
LEDs display user-selectable High/Medium/Low levels with sensitivity of 0.25/0.50/0.99 oz per year
Audible and Visual alert with mute button
Low battery indicator
Field replaceable sensor and LED light tip
Complete with leak test bottle, 9V battery, and protective hard carrying case

The MOTWANE make OIL TEST SET (MOT-OTS) are used to verify the quality of the insulation oil used for circuit breakers, transformers. The insulating oil provides the insulation under high voltage potentials. The di-electric strength of insulating oil measures the ability of the oil to withstand the electrical stresses without failures. Any severe reduction in the value of the di-electric, will no longer allow the insulating oil to perform its role & equipment is subjected to failure. We have the different models with range of output voltages from 60KV to 100 KV, as per the requirements.

Features:

Equipment with single unit compact design.

Use for measurement of di-electric strength of insulating oil used for oil circuit breakers, Transformers.

Designed to offer continuously variable output voltage, manually/auto

Different models for different outputs like 60KV, 80KV, 100KV

Fast acting over current protection for overload

Suitable for conducting tests as per IS 6792-1992

Output voltmeter is with memory effect, in case of failure of supply or tripping the voltmeter continues to show the reading at which the supply fail/tripped

It is provided with GO/NOGO gauges.

The HDV-WTX is a Wireless Video Transmitter. For use with any Extech HDV-Series Video Scope Camera Heads and HDV Series Videoscope inspection cameras. Comes with a year warranty.

CE 1 Year Warranty

Features:

Compatible with HDV-4CAM-xx, HDV-5CAM-xx and HDV-25CAM-xx probes (camera heads)
Wireless transmission to HDV600 VideoScope
Brightness and Power On/Off controls

8mm camera diameter and 2.7" Color TFT LCD Monitor

Features:

8mm diameter camera head with 4 built-in bright LED lamps for dimly lit areas
Handheld design for quick, easy, on-the-spot viewing in small openings
Completely submersible in water down to 1 meter for 1 hour
Non-detachable waterproof 39" (1m) flexible gooseneck cable retains configured shape
2.7" (68mm) color TFT LCD monitor for detailed images
2x digital zoom for close-up viewing
Low battery indicator
Complete with camera probe and 39" (1m) flexible cable, 4 AA batteries, and hard case

The SC50 is a Digital Luggage Scale. Battery operated with webbing belt and hook that attaches to luggage handle and featuring a touch-screen. Complete with CR2032 battery, 9.4" (238mm) strap, and metal hook.

Features:

Ideal for home, sports, and industrial use
1.6" color LCD with 0.5" digits provides Weight and Tare indication
Measure up to 110lbs/50kg with 0.01lb (0.01kg) resolution
Simple touchscreen Zero and Tare programming
Automatic 30 seconds Data Hold
Auto Power Off in 30 seconds
Overload indicator
Complete with CR2032 battery, 9.4" (238mm) strap, and metal hook

Water resistant decimal stopwatch/clock with user-selectable resolutions
This Decimal Stopwatch/Clock has user-selectable resolutions of 1/100th of a second, 1/1000 of a minute, and 1/100, 000th of an hour. Additional features includes pacer from 5 to 240 beeps per minute and a large triple display with adjustable contrast. Complete with CR2032 lithium battery and 39" (1m) neck strap.

Features:

User-selectable resolutions of 1/100 of a second, 1/1000 of a minute and 1/100, 000 of an hour
Large triple display with adjustable contrast
500 memory records of Split and Lap times
Calendar displays day, month and date
Time of day (12 or 24 hour format) with daily alarm
3 Mode Countdown timer: count down stop, count down repeat, count down then count up
Stroke measurement
Pacer from 5 to 240 beeps per minute
Complete with CR2032 lithium battery and 39in (1m) neckstrap

Offering 11 selectable units of measure, the HD700 Differential Pressure Manometer can serve as a low range/high resolution Gauge or provide Differential Pressure up to 0 to 55.40 in. H2O (inches of water). Max/Min recording and Relative time stamp are useful features, as are HD700's Data Hold and Auto Power Off functions. The 2psi HD700 also features Zero function for offset correction or measurement and a built-in USB interface. Comes complete with 9V battery, software with USB cable, AC Adaptor, connection hose, built-in stand, and hard carrying case.

Features:

2psi range, 11 Selectable units of measure
Max/Min/Avg recording and Relative time stamp
Data Hold, Auto power off and Zero function
Large LCD display with backlighting
Heavy duty, double-molded housing
Built-in USB port (Windows compatible PC software and cable included)

48VFL11 Temperature PID controller offers Fuzzy Logic enhanced PID and a Soft-Start feature that protects heaters from cold-starts. PID plus Fuzzy Logic tackles even the most demanding applications, eliminating over-shoot, unwanted process fluctuations, and drift. The Soft Start feature is ideally suited for processes, such as those employed in the Thermo-Plastics industry, where careful, exact, and slow heating of product is required. Accepts thermocouple and RTD inputs. Single stage Ramp and Soak program with Ramp-to-Set point Limit that can be combined with the Soft Start feature for critical process demands. Complete with mounting bracket hardware and screw terminals for easy wiring. Also available with 4-20mA output (48VFL13).

Features:

One relay output
Dual 4-digit LED displays of process and setpoint values
User friendly menus and tactile keypad for easy programming
One-touch autotuning for quick setup & precise control
Fuzzy Logic PID offers intuitive control simulating human control logic
Two "Latching" alarm relays standard with 8 Alarm modes
Accepts thermocouple and RTD inputs
This product is also available with 4-20mA output - 48VFL13