Features

• The Torch cooling process through gas

• The Shielding gas is inert, the welding process is known as MIG process

• The gas has a definite chemical process activity at the high temperature of the electric

arc is known as MAG process.

• The Torch use as continuous welding process, need not required changing electrode

frequently

• Conform to IS 7931

Features

• Flash Back Arrestor is a device to eliminate every possibility of explosion or fire

caused by flashback.

• Flash Back Arrestor is suitable for fitting on the regulator outlet.

• Oxygen for use at a maximum inlet pressure 10 bar (150psi).

• Fuel gas : Acetylene / Propen / LPG at a max. inlet pressure of 8 bar (43 psi)

• Conform to IS 11006

Features

• Gas pre-heater is used for heating the CO gas to the boiling point, before it enters

into the Regulator.

• Heater is so designed to sufficient cooling the heater during the cylinder valve and

integrate in piping system.

• It is thermostat resistant control which maintain constant temperature of 60°+3°C

Features

• The Torch cooling process through water

• It is a continuous welding process, need not required changing electrode frequently

• • It’s a Low Pressure Cutting Blowpipe
• • Gas Mixing : Injector Type Mixer
• • Working Pressure :2.5 kgf/cm² to 4.0 kgf/cm²
• • 2 Seat Nozzle
• • Resistance to Backfire.
• • ISI approved IS 7653:1975

Features

• Gouging Torches are used to Gouge, Crompter, Grove cut, Bevel, Flash of various

metals like Aluminum, Copper, Brass, Steel & Cast Iron.

• For high conductivity of current, special grade copper/copper alloy used.

• Heat resistant insulators

• 360°free revolving movement between torch and mono cable.

• Uses compressed air between 5.6 and 7.0 kg./cm (80 and 100 psi)

• Standard Length of Cable is 2 mt. long (additional length available on demand)

• Weight of Torch 2.6 kg.(approx)

• 600Amps., 900Amps., 1200Amps., 2000Aps.

Features

• Type-A is fully insulated, suitable adverse welding

conditions

• Type-B is semi insulated for general open shop

conditions

• Rated Current : 200, 400 and 600 Amps.

• Conform to IS 2641

Features

• Flow meter used with regulator or pipeline distribution

installation.

• Precision machined forged brass body.

Description:

Anchor Point: One Dorsal 0-ring And Two Textile Chest Attachment Loop. 

Special Features: Ideally Positioned Sit-strap For Extend. Comfort 

Built-in Dual Colour Webbing For Easy Orientation.

Type -a & L Conform

Materials: Fray-proof Dope-dyed Polyester Webbing Metal Buckles Of 

High Strength Alloy Steel.

Stitching: High-strength Polyester Stitching.

Adjustability: Size Adjustment Straps Only At Chest And Thighs. 

Standard: Is 3521(Part-1) & Is 3521(Part-2) Isi Marked

"In-built Fall Indicator To Facilitate Easy Inspection In Case A Fall Has 

Occurred Ever"

Description:

Full Body Harness: Anchor Point: One Dorsal D.ring And Two Textile Chest 

Attachment Loop.

Special Features: Ideally Positioned Sit-strap For Extended Comfort Built-in 

Dual Colour Webbing For Easy Orientation

Materials: Fray-proof Dope Dyed Polyester Webbing, Metal Buckles Of 

High Strength Alloy Steel,

Stitching: High-strength Polyester Computerised Stitching.

Adjustability: Chest And Thigh.type: A & L

`in-built Fall Indicator To Facilitate Easy Inspection In Case A Fall Has 

Occurred Ever'

Lanyard: Material: Twisted Polyamide Rope.total Length: 1.8 Mtr. 

Double Lanyard With Two Scaffold Hook.

Standard: IS 3521(Part-1) & Is 3521(Part-2)ISI Marked

Features

• The Torch cooling process through gas

• The Shielding gas is inert, the welding process is known as MIG process

• The gas has a definite chemical process activity at the high temperature of the electric

arc is known as MAG process.

• The Torch use as continuous welding process, need not required changing electrode

frequently

• Conform to IS 7931

Features

• Flash Back Arrestor is a device to eliminate every possibility of explosion or fire

caused by flashback.

• Flash Back Arrestor is suitable for fitting on the regulator outlet.

• Oxygen for use at a maximum inlet pressure 10 bar (150psi).

• Fuel gas : Acetylene / Propen / LPG at a max. inlet pressure of 8 bar (43 psi)

• Conform to IS 11006

Features

• Gas pre-heater is used for heating the CO gas to the boiling point, before it enters

into the Regulator.

• Heater is so designed to sufficient cooling the heater during the cylinder valve and

integrate in piping system.

• It is thermostat resistant control which maintain constant temperature of 60°+3°C

Features

• The Torch cooling process through water

• It is a continuous welding process, need not required changing electrode frequently

• • It’s a Low Pressure Cutting Blowpipe
• • Gas Mixing : Injector Type Mixer
• • Working Pressure :2.5 kgf/cm² to 4.0 kgf/cm²
• • 2 Seat Nozzle
• • Resistance to Backfire.
• • ISI approved IS 7653:1975

Features

• Gouging Torches are used to Gouge, Crompter, Grove cut, Bevel, Flash of various

metals like Aluminum, Copper, Brass, Steel & Cast Iron.

• For high conductivity of current, special grade copper/copper alloy used.

• Heat resistant insulators

• 360°free revolving movement between torch and mono cable.

• Uses compressed air between 5.6 and 7.0 kg./cm (80 and 100 psi)

• Standard Length of Cable is 2 mt. long (additional length available on demand)

• Weight of Torch 2.6 kg.(approx)

• 600Amps., 900Amps., 1200Amps., 2000Aps.

Features

• Type-A is fully insulated, suitable adverse welding

conditions

• Type-B is semi insulated for general open shop

conditions

• Rated Current : 200, 400 and 600 Amps.

• Conform to IS 2641

Features

• Flow meter used with regulator or pipeline distribution

installation.

• Precision machined forged brass body.

Description:

Anchor Point: One Dorsal 0-ring And Two Textile Chest Attachment Loop. 

Special Features: Ideally Positioned Sit-strap For Extend. Comfort 

Built-in Dual Colour Webbing For Easy Orientation.

Type -a & L Conform

Materials: Fray-proof Dope-dyed Polyester Webbing Metal Buckles Of 

High Strength Alloy Steel.

Stitching: High-strength Polyester Stitching.

Adjustability: Size Adjustment Straps Only At Chest And Thighs. 

Standard: Is 3521(Part-1) & Is 3521(Part-2) Isi Marked

"In-built Fall Indicator To Facilitate Easy Inspection In Case A Fall Has 

Occurred Ever"

Description:

Full Body Harness: Anchor Point: One Dorsal D.ring And Two Textile Chest 

Attachment Loop.

Special Features: Ideally Positioned Sit-strap For Extended Comfort Built-in 

Dual Colour Webbing For Easy Orientation

Materials: Fray-proof Dope Dyed Polyester Webbing, Metal Buckles Of 

High Strength Alloy Steel,

Stitching: High-strength Polyester Computerised Stitching.

Adjustability: Chest And Thigh.type: A & L

`in-built Fall Indicator To Facilitate Easy Inspection In Case A Fall Has 

Occurred Ever'

Lanyard: Material: Twisted Polyamide Rope.total Length: 1.8 Mtr. 

Double Lanyard With Two Scaffold Hook.

Standard: IS 3521(Part-1) & Is 3521(Part-2)ISI Marked