Unioversal Scientific Pvt. Ltd.

Badli, Delhi

This is used for determination of resistance to wear for cement concrete flooring tiles. Tiles specimen of size 7.06cm x 7.06cm is pressed tace wise under specific load on a grinding path and abrasive powder is evenly spread on the rotating grinding path and after specific number of revolutions of the grinding disc the second parallel side of the tile is subjected to wear for similar under of rotations. The wear of the tile is measured on a thickness gauge specifically made for the purpose. The machine consists of a disc rotating at a speed of 30 rpm in a circular tray. A bracket is provided to hold the specimen. A counter balance lever loads the specimen. Load applied is 30kgf. A funnel is fitted to evenly spread abrasive powder on the grinding path. A pre-set counter automatically stops the machine after 22 revolutions. This counter is re-adjustable. The machine works on 440 volts AC, 3 phase electrical supply.

The offered oven is manufactured with the help of quality approved material and advanced technology. This oven is tested on various stages by our professionals as per the set industrial norms. It is ideal for performing under high pressure and temperature in various industries.

Laboratory Concrete Mixer. Designed to remove the burden some work of hand mixing. Uniform thoroughly mixed batches can be produced. The counter balanced drum is easily to tilt 1  to 2 Cu.Ft.mix. The total drum volume is however 3 Cu.ft. Mounted on a sturdy rubber typed stand, the drum is mounted for end discharge and equipped with end towing pole. Equipped with 1 H.P. electric motor, suitable for operation on 220 volts, single phase 50 cycles A.C.supply.

Located in Delhi(India), ours is the name trusted for meeting the exact requirements of the clients. Listed amidst the renowned Suppliers of Vibrating Table, we successfully deliver the finest range of products the clients. It is used for compacting concrete cubes and cylinders

Specifications :

• Sizes - 75cmx75cm & 100cmx100cm. To carry out a load of 140kg. The unit consists of a motor fitted with a variable pitch pulley housed in a cabinet. The vibrations are imparted by means of off balance masses rotating on a shaft of a vibrator clamped to the underside of the table top.
• The table top is 50cm x 50cm and has stops along its edges to prevent moulds form walking off the table during vibration. A cross arm adjustable on a vertical rod at the centre of the table is provided to hold the moulds while operating the table. The variable pitch pulley arrangement permits the frequency to be varied step Lesley between a maximum of 3600 vibrations down to 2600 vibrations per minute. A speed regulation handle is provided for increasing or decreasing the frequency a switch is provided for starting the motor. Suitable for operation on 440 Volts, 3 phase, 50 cycles, A.C.Supply.

We are flexible enough to deliver the products that we make available across Delhi(India). We are here to guide our clients with the secure payment procedures. With us, the customers get convenience to pay through both online and offline payment methods Inner chamber made of S.S., outer body mild steel duly powder coated. Suitable to accommodate 12 cube moulds of 150mmx150mmx150mm. The unit is provided with digital temperature controller cum indicator and water circulation pump. Temperature range 5^o above ambient to 100^oC.  12 KW and 3 Phase Chamber Size : 1200mm x 675mm x 375mm

Concrete Moulds are easily cast by using a tamping bar or a vibrating table. However air trapped in cement mortar paste can not be thus removed while casting cement mortar moulds. Easy method is to impart greater vibration of lesser amplitude to the mould while casting. This is achieved in a Mortar Vibrating Machine. Mortar Vibrating Machine is used for the preparation of mortar cubes for the determination of compression strength of ordinary and rapid hardening Portland cement, low heat Portland cement, Portland blast furnace cement and high alumina cements.

Specifications : The machine consists of a vibrating frame assembly and an electric motor mounted on a sturdy base. The complete frame assembly consists of a vice to hold a 7.06cm cube mould and two studs threaded at top and a hopper to feed the sample in the mould. This assembly is supported on four springs and has an in built rotating shaft which rotates eccentrically and thus imparts vibrations to the entire frame. A balance weight is an integral bottom part of the frame. The centre of gravity of the assembly is brought to the centre of the eccentric shaft or within a distance of 25mm below it. The electric motor drives the shaft of the frame and thus imparts required vibrations to the mould. The frequency of vibration is 12000 ± 400 vibration per minute. Supplied complete with a 7.06cm cube mould and loose base plate, a time switch 0-5mins x 1 min and certificate of vibration.

Pan mixer capacity 40Litres 3 phase 440 volts fitted with 2hp standard motor.RPM 30 TO 35. Only quality packaging material has been used for the packing of the products that we offer. Moreover, the entire packaging procedure is conducted under the supervision of the experts. We make sure that our payment procedure is safe and simple. We offer our clients methods like online payment gateway, electronic funds transfer, cash, bank deposits and various others.

Machine is suitable to Cut/Drill cores of Concrete and the similar material. The machine is suitable for core samples of size upto 100mm diameter with the help of thin walled Diamond bits which are at extra cost. The machine has sturdy base with pillar support in which rack & pinion is provided for adjustment in height and penetration assembly. The leveling screws are provided at the base. For gripping the sample in position suitable grips are provided. Greaves Make 5 H. P Diesel Engine is fitted in the machine with cooling arrangement with water. The base frame is also fitted with wheels for ease of transportation.