Our Products

Fluid Mechanics Lab

We offer the best product range of Centrifugal Pump Test Rig, Losses Due to Pipe Friction, Losses Due to Pipe Fittings, Metacentric Height Apparatus and Reynolds Apparatus.

Centrifugal Pump Test Rig

Centrifugal Pump Test Rig Closed Circuit Type With S.S. Tanks, ISI Mark Pumps & Motors, Powder coated The closed circuit test rig consists of a "kirloskar make" monoblock centrifugal pump. The pump is provided with a vacuum gauge on suction pipe and a pressure gauge on discharge pipe. The gate valve is used to adjust the head on the pump. The discharge is measured by measuring tank water flow meter. The input power is measured by energy meter. Specifications: l. Centrifugal monoblock- 1 h.p. 2. Pressure gauge and vacuum gauge for measuring the head. 3. Measuring tank of 400x400 x400 mm OR Water flow energy meter for measuring the discharge. 4. Stop watch. 5. Sump tank of sufficient capacity. 6. Energymeter to measure input power. A technical manual accompanies the equipment. Features: 1. The equipment is coated with an attractive and anticorrosive powder coating. 2. The equipment consists of ISI standard (i) Monoblock ------------------------- Kirloskar make (ii) Energymeter ------------------------- Maxwell Jaipur make (iii) Water flow meter ------------------------- KrantiAnand make. Services required : i) 440 v, 15 A, stabilized three phase A.C. supply. ii) Floor area-2 mx2mxl.5m height iii) Tachometer for speed measurement (can be supplied at extra cost)

View Complete Details

Ask Latest Price & Details

Losses Due To Pipe Friction

Losses Due To Pipe Friction DESCRIPTION:- The Set-up consists of 2 pipes of different diameters, which are connected in parallel. Pressure tapings are provided on each pipe to measure the pressure losses with the help of a Differential Manometer. Control valves are fitted on each pipe, which enables to use one pipe at a time for experiment. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch. EXPERIMENTS:- To determine the losses due to fiction in pipes To determine the friction factor for Darcy Weis back equation UTILITIES REQUIRED: - Water Supply & Drain Electricity Supply: Single Phase, 220 VAC, 0.5 kW TECHNICAL SPECIFICATION: - Pipes (2 Nos.) : Material GI of & 1 Diameter Pipe Test Section : Length 1 m Water Circulation : FHP Pump, Crompton Sharp make Flow Measurement : Using Measuring Tank with Piezometer, Capacity 25 Ltrs. Sump Tank : Stainless Steel, Capacity 50 Ltrs. Stop Watch : Mechanical Electronic Control Panel : On Off Switch, Mains Indicator etc. The whole Set-up is well designed and arranged in a good quality painted Structure

View Complete Details

Ask Latest Price & Details

Losses Due To Pipe Fittings

We are offering losses due to pipe fittings description:- the set-up consists of a bend and elbow, a sudden expansion & sudden contraction fitting from 15 mm to 25 mm, ball valve and gate valve. Pressure tapings are provided at inlet and outlet of these fittings under test. A differential manometer fitted in the line gives pressure loss of individual fitting. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch. Experiments:- to determine loss of head in the fitting at various water flow rates. to measure the loss co-efficient for the pipe fittings. Utilities required: - water supply and drain electricity supply: single phase, 220 v ac, 0.5 kw. Technical specification: - sudden enlargement : from 15 mm to 25 mm sudden contraction : from 25 mm to 15 mm bend : elbow : ball valve : gate valve : water circulation : fhp pump, crompton sharp make flow measurement : using measuring tank with piezometer, capacity 25 ltrs. sump tank : capacity 50 ltrs. stop watch : electronic control panel : on off switch, mains indicator etc. The whole set-up is well designed and arranged in a good quality painted structure

View Complete Details

Ask Latest Price & Details

Metacentric Height Apparatus

METACENTRIC HEIGHT APPARATUS DESCRIPTION:- A pontoon is allowed to float in a small tank having a transparent side. Removable steel strips placed in the model for the purpose of changing the weight of the model. Displacement of weight is measured with the help of a scale. By means of a pendulum (consisting of a weight suspended to a long pointer) the angle of tilt can be measured on a graduated arc. For tilting the ship model, a cross bar with two movable hangers is fixed on the model. Pendulum and graduated arc are suitably fixed at the center of the cross bar. A set of weights is supplied with the apparatus. EXPERIMENTS:- Determination of the Metacentric height and position of the Metacentric height with angle of heel of ship model. TECHNICAL SPECIFICATION: - Pontoon : Size 300 x 150 mm (Approx.) with a Horizontal Guide Bar for aliding weight. Material : Stainless Steel Pontoon Water Tank : Size 600 x 400 x 400 mm (Approx.) Front Window of Tank : made of GlassPerspex A set of weights is supplied with the apparatus. The whole Set-up is well designed and arranged in a good quality painted Structure.

View Complete Details

Ask Latest Price & Details

Reynolds Apparatus

We are offering reynolds apparatus.Reynolds apparatus description:-the set-up is designed to verify reynolds apparatus experimentally. The apparatus consists of a glass tube which one end having bell mouth entrance connected to a water tank. At the other end of the glass tube a cock is provided to vary the rate of flow. Flow rate of water can be measured with the help of measuring cylinder and stop watch, supplied with the set-up. A capillary tube is introduced centrally in the bell mouth. To this tube dye is fed from a small container, placed at the top of constant head tank, through polythene tubing. experiments:- to study different types of flow.to determine the reynolds number and hence the type of floe either laminar or turbulent. utilities required: - water supply.drain. technical specification: - tube : material borosilicate glassdye vessel : material ss, suitable capacitycapillary tube : material copperstainless steelconstant head water tank : capacity 40 liters.water circulation : fhp pumpflow measurement : using measuring cylindersump tank : capacity 60 liters.stop watch : electroniccontrol panel comprises of : standard make, onoff switch, mains indicator, etc.the whole set-up is well designed and arranged in a good quality painted structure.

View Complete Details

Ask Latest Price & Details

Bernoulli Theorem Apparatus

BERNOULLIS THEOREM APPARATUS DESCRIPTION:- The Set-up is designed to verify Bernoullis Theorem experimentally. Set up consists of a one piece clear acrylic test section with convergent and divergent part section, supply tank, measuring tank, inlet water tank and pump for closed loop water circulation. The test section is connected to Piezometer tubes through pressure tapping at different locations on the section to demonstrate the Bernoullis Theorem. The flow rate of water is measured using measuring tank and stop watch provided. EXPERIMENTS:- To verify Bernoullis Theorem experimentally. FEATURES:- Clear test section Closed loop water circulation Compact & stand alone setup Stainless Steel tanks and wetted parts Superb Painted structure Simple to operate & maintain UTILITIES REQUIRED: - Electricity Supply: Provide 230 +- 10 VAC, 50 Hz, Single Phase electric supply with proper earthing (Neutral Earth voltage less than 5 VAC) 5 A, three pin socket with switch for pump Water Supply : Tap water connection BSP, Distilled water @ 60 Ltrs. (Optional) TECHNICAL SPECIFICATION: - Test Section : Material Acrylic, Size Inlet Tank : Capacity 20 Liters., Stainless Steel Supply Tank : Capacity 70 Liters., Stainless Steel Measuring Tank : Capacity 20 Ltrs. Fitted with Piezometer Tube & Scale Piezometer Tubes : Material P.U. Tubes (9 Nos.) Pump : FHP Capacity make TulluCrompton Graves Piping : GI PVC Size BSP Stop Watch : Electronic The whole Set-up is well designed and arranged in a good quality painted Structure.

View Complete Details

Ask Latest Price & Details

Discharge Over Notches Apparatus

Brand Name UNICON
Model Number UI-2413

We are offering discharge over notches apparatus. Description:-the lab setup consists of a channel having sufficient length and width in which water is supplied from the bottom. Required notch is fitted at one end of this channel .a hook gauge with vernier scale is fitted to measure the height of fluid in flow channel. Arrangement for fixing interchangeable notches is made. Set of three brass notches, i.e. Rectangular notch. 60 v notch & 45 v notch provided along with the set up. Present set up is self contained water re- circulating unit .provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass value are fitted in water line to conduct the experiment on different flow rate .flow rate of water is measured with the help of measuring tank and stopwatch. experiments:-to determination co-efficient of discharge (cd) throughv notch (45 deg. And 60 deg.)rectangular notch.trapezoidal notch utilities required: -water supply & drainelectricity 0.5kw, 220v ac, single phase technical specification: -channel test section : size 600x250x180 mmnotches : material brass(3 nos)1. rectangular notch2. 45 deg. V notch3. 60 deg. V notch4. trapezoidal notchhook pointer : with vernier scalewater circulation : fhp pump, cromptonsharp make.flow measurement : using measuring tank with piezometer, cap.25 ltrs.sump tank : capacity 70 liters.stop watch : electroniccontrol panel : onoff switches, main indicator etc.the whole set-up is well designed and arranged in a good quality painted structure.

View Complete Details

Ask Latest Price & Details

Hydraulic Bench Apparatus

HYDRAULIC BENCH APPARATUSOBJECTIVE: To conduct the experiment of hydraulic bench, with separate experiential set ups i.e. Hydrostatic Pressure, Flow over Weirs, Bernoullis Theorem, Flow meter Demonstration, Impact of jet and Orifice Discharge etc. which are accessories of the Hydraulic Bench. DESCRIPTION OF APPARATUS: The set up is a self-contained, water recirculation unit provided with a top tray, sump tank and a measuring tank. Drain valve and over-flow are provided on the sump tank. A centrifugal pump is fitted for water circulation. Flow control valve and bypass valve is fitted in water line to conduct the experiment at different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch. Measuring tank is provided to measure the discharge. Drain valve is provided in the measuring tank to empty water in sump tank after measuring discharge. Separate level indicator and scale is provided to read the level of water in the measuring tank. UTILITIES REQUIRED: Water Supply (Fill approx 250 Ltrs Initially).Drain Required.220 V AC, 50 Hz, single phase electric supply source.Floor area 1.75 m x 1.50 m. SPECFICATION: Top Tray : 1060 mm x 650 mm.Pump : 1 HPFlow Measurement : Using measuring Tank (Material SS)Tank : Capacity 40 Ltr.Sump Tank : Capacity 120 Ltr. Material SS.The whole set-up is well designed and arranged in a good quality powder coating painted structure. RANGE OF EXPERIMENTS:- Following experiments can be carried out with common basic table with separate experimental setup (supplied at extra cost), which can be connected to Hydraulic Bench with flexible pipe.

View Complete Details

Ask Latest Price & Details

Orfice Mouthpieces Apparatus

Orfice & Mouthpieces Apparatus An orifice is an opening made in the side or bottom of tank, having a closed perimeter, through which the fluid may be discharged. A mouthpiece is short tube fitted to a same size circular opening provided in a tank so that fluid may be discharged through it. Orifice and mouthpiece are used to measure the rate of flow of liquid. The apparatus is designed to measure the co-efficient of discharge of orifice & mouthpiece. The apparatus consists of a supply tank, at the side of which a universal fixture for mounting orifice or mouthpiece is attached. A centrifugal pump supplied the water to supply tank. Head over the orificemouthpiece is controlled by a by pass valve provided at pump discharge. A measuring tank is provided to measure the discharge. A gauge for measuring X and Y co-ordinates of jet from the orifice is provided, which is used to calculate Cv of orifice. SPECIFICATIONS: [1] Supply Tank - 0.4 X 0.3 X 0.5m height[2] Orifice - 8mm and 10 mm.[3] Mouthpiece(a) LID = 4(b) LD = 1(c) Bordas mouthpiece.(d) Convergent mouthpiece.[4] X-Y gauge for orifice jet co-ordinates.[5] Measuring tank of suitable capacity OR a calibrated water flow meter.[6] Sump tank of suitable capacity.[7] 0.5 HP pump with valve. A technical manual accompanies the unit. SERVICES REQUIRED: [1] Flow surface 2 mtrs. X 1 mtr. X 1.5 mtrs. height. [2] 230 Volts, 5 Amp. Stabilized AC. Power Supply.

View Complete Details

Ask Latest Price & Details

Hydraulic RAM Test Setup

HYDRAULIC RAM TEST SETUPDESCRIPTION:- The Set-up is designed to study the Hydraulic Ram. Hydraulic RAM is used for pump little quantity of water to high head from a large quantity of water available at low head. It works on a principle of water hammer stating that When flowing water is suddenly stopped in a long pipe a pressure wave travels along the pipe creating an effect of water hammer. The Set-up consists of a pipe section fitted with a pulse valve and non-return valve, a supply reservoir on a stand which is connected to an overhead tank, an air vessel above the valve chamber smoothes cyclic fluctuations from the Ram delivery. Different pressure may be applied to the pulse valve to change the closing pressure and hence the operating characteristic. The flow rate of useful and waste water is measured using measuring tank and stop watch provided. Pressure and Vacuum Gauge are connected on delivery and suction side for the purpose of measurement. EXPERIMENT:- To find out discharge of useful water and waste water. To find out the efficiency of the Hydraulic RAM FEATURES:- Closed loop water circulation Compact & stand alone set-up MS Excel sample calculation program on demand Stainless Steel tanks and wetted parts Superb painted structure Simple to Operate & Maintain UTILITIES REQUIRED:- Electric Supply: - Provide 230 +- 10 VAC, 50 Hz, Single Phase Electric Supply with proper earthing. (Neutral Earth voltage less than 5 VAC) 5 A, three pin socket with switch for pump. Water Supply: Tap water connection BSP Distilled water @ 90 Ltrs. (Optional) TECHNICAL SPECIFICATIONS: - Product : Hydraulic RAM RAM : Size 50 x 15 mm, Supply Head 2.5m, Delivery Head 10 m (max.)

View Complete Details

Ask Latest Price & Details

Venturimeter & Orificemeter Calibration

Brand Name UNICON
Model Number UI-2414

We offer Venturimeter & orificemeter calibration set-up description:-the apparatus consists of two pipelines emerging out from a common manifold. One pipeline contain a venturimeter, second contains an orifice. The pressure tapings from the venturimeter and orificemeter are taken to differential manometer to measure pressure difference. The venturimeter and orificemeter are connected in parallel and anyone of them can be put in operation by operating valves provided at the downstream. These valves can also regulate the flow. Present set-up is self contained water re-circulating unit, provided with a sump tank and a centrifugal pump. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different floe rate. Flow rate of water is measured with the help of measured with the help of measuring tank and stop watch. experiments:-to determine the co-efficient of discharged through venturimeter and orificemeterto measure discharge through venturimeter and orificemeter as flow meters. utilities: -water supply & drainelectricity supply: single phase, 220 vac, 0.5 kw technical specifications: - venturimeter : material clear acrylic, compatible to 1 dia pipeorificemeter : material clear acrylic, compatible to 1 dia. Pipewater circulation : fhp pump, crompton sharp makeflow measurement : using measuring tank, capacity 25 ltrs. sump tank : capacity 50 ltrs. stop watch : electroniccontrol panel : on off switch, mains indicator etc. tanks will be made of stainless steelthe whole set-up is well designed and arranged in a good quality painted structure

View Complete Details

Ask Latest Price & Details

Francis Turbine Test Setup

Brand UNICON
Model Number UI-2462

offers francis turbine test setup.description:- francis turbine is a reaction turbine, which was developed by english born american engineer sir j. b. francis. the water enters the turbine through the outer periphery of the runner in the radial direction and leaves the runner in axial direction and hence it is called a mixed flow turbine. as the water flows to the runner, a part of pressure energy goes on changing into kinetic energy. thus the water through the runner is under pressure. the runner is completely enclosed in an air tight casing and the casing & runner is always full of water. the present set-up consists of a runner. the water is fed to the turbine by means of centrifugal pump, radially to the runner. the runner is directly mounted on one end of a central ss shaft and other end is connected to a brake arrangement. the circular window of the turbine casing is provided with a transparent. the circular window of the turbine casing is provided with a transparent acrylic sheet for observation of flow on to the runner. the runner assembly is supported by thick cast iron pedestal. load is applied to the turbine with the help of brake arrangement so that the efficiency of the turbine can be calculated. a draught tube is fitted on the outlet of the turbine. the set-up is complete with guide mechanism. pressure and vacuum gauge are fitted at the inlet and outlet of the turbine to measure the total supply head on the turbine. experiment:- to study the operation of a francis turbineto determine the output power of francis turbineto determine the turbine efficiencyutilities required:- water supply and drain. electricity 15 kw, 440v ac, three phase technical specifications: model hm 101 (1. 33 hp) hm 101 (2 hp) hm 101 (5 hp) output power 1. 33 hp 1 kw 2 hp 1 kw 5 hp 3. 75 kw discharge 1000 lpm (approx. ) 1000 lpm (approx. ) 2000 lpm (approx. ) supply head 10 m 10 m 15 m.

View Complete Details

Ask Latest Price & Details

Pelton Wheel Turbine Test Setup

Brand Name UNICON
Model Number UI-2461

We are offering pelton wheel turbine test setup.Description:-pelton wheel turbine is only impulse water turbine now in common use named in honor of sir l.a. Pelton (1829-1908) of california, usa. It is a tangential flow impulse turbine. The water strikes the buckets along the tangent of the runner. The energy available at the inlet of the turbine is only kinetic energy. The pressure at the inlet and outlet of the atmospheric. This turbine is used for high heads. The present set-up consists of a runner. The buckets are mounted on the runner. The water is fed to the turbine, through ss nozzle with a ss spear, by means of centrifugal pump, tangentially to the runner. Row of water into turbine is regulated by adjusting the spear position by the help of a given hand wheel the runner is directly mounted on one end of a central ss shaft and other end is connected to a brake arrangement. The circular window of the turbine casing is providing with a transparent acrylic sheet for observation of flow on to the buckets. This runner assembly is supported by rigid ms structure. Load is applied to the turbine with the help of this brake dynamometer so that the efficiency of the turbine can be calculated. Pressure gauge is fitted at the inlet of the turbine to measure the total supply head to the turbine.Experiment:-1. to study the operation of a pelton wheel turbine2. to determine the output power of pelton wheel turbine3. to determine the turbine efficiencyutilities required:-water supply and drain. electricity 15 kw, 440v ac, three phase technical specifications: - model hm 111 (1.33 hp) hm 111 (2 hp) hm 111 (5 hp)output power 1.33 hp 1 kw 2 hp 1.5 kw 5 hp 3.75 kwdischarge 300 lpm (approx.) 400 lpm (approx.) 630 lpm (approx.)supply head 25 m 40 m 45 mrope brake dynamometer dia 200 mm dia 200 mm dia 300 mmsump tank capacity 150 liters. capacity 200 liters. capacity 300 liters.Water circulation centrifugal pump capacity 5 hp, three phase capacity 7.5 hp, three phase

View Complete Details

Ask Latest Price & Details

Impact Of Jet On Vanes Apparatus

Impact of jet on vanes apparatus description:- the set-up consists of two sided clear fabrication. Water is fed through a nozzle and discharged vertically to strike a target carried on a stem, which extends through the cover. A weight carrier is mounted on the upper end of the stem. The dead weight of the moving parts is counter balanced by a compression spring. The vertical force exerted on the target plate is measured by adding the weights supplied to the weight pan until the mark on the weight pan corresponds with the level gauge. A total of two targets are provided a flat plat and a hemispherical cup. Experiments:- to measure the force developed by a jet of water impinging upon a different targets (hemispherical & flat plate) and comparison with the forces predicted by the momentum theory. Utilities required: - water supply & drain electricity supply: single phase, 220 vac, 0.5 kw technical specification: - test plates : material brass (2 nos.) 1. flat plate 2. hemispherical cup nozzle : material brass stainless steel chamber : having of opposite sides made of glass water circulation : fhp pump, crompton sharp make flow measurement : using measuring tank with piezometer, capacity 40 ltrs. sump tank : capacity 60 ltrs. stop watch : electronic control panel : on off switch, mains indicator etc. The whole set-up is well designed and arranged in a good quality painted structure

View Complete Details

Ask Latest Price & Details

Kaplan Turbine Test Setup

Brand Name UNICON
Model Number UI-2463

We are offering kaplan turbine test setupdescription:-kaplan turbine is an axial flow reaction turbine named in honor of dr. B. Kaplan, a gennan engineer. This turbine is suitable for low head. The power produced by a turbine is proportional to qh. As the head (h) decreases the j discharge (q) must increase to produce the same power. The present set-up consists of a scroll casing housing a runner. Water enters the turbine through the stationary guide vanes and passes through the runner axially. The runner has a hub and airfoil vanes, which are mounted on it. The water is fed to the turbine by means of centrifugal pump. The runner is directly mounted on one end of a central ss shaft and other end is connected to a brake arrangement. A transparent hollow cylinder made of acrylic is fitted in between the draught tube and the casing for observation of flow on to the airfoil vanes. This runner assembly is supported by thick cast iron pedestal. Load is applied to the turbine with the help of this brake arrangement so that the efficiency of the turbine can be calculated. The set-up is supplied with control panel. A draught tube is fitted on the outlet of the turbine. The set-up is complete with guide mechanism. Pressure and vacuum gauge are fitted at the inlet & outlet of the turbine to measure the total supply head on the turbine.Experiment:-to study the operation of a kaplan turbineto determine the output power of kaplan turbineto determine the turbine efficiencyutilities required:-water supply and drain. electricity 15 kw, 440v ac, three phasetechnical specifications: -model hm 109 (1.33 hp) hm 109 (5 hp)output power 1.33 hp 1 kw 5 hp 3.75 kwdischarge 1500 lpm (approx.) 5000 lpm (approx.)supply head 5 m 5 mrope brake dynamometer dia 200 mm dia 300 mmsump tank capacity 300 liters. capacity 600 liters.Water circulation centrifugal pump capacity 7 hp, three phase capacity 20 hp, three phasespeed 1500 rpm (approx.)

View Complete Details

Ask Latest Price & Details

Tell Us What are you looking for? Will call you back