Star Knobs

temperature resistant -25 °C to + 150 °C

Star knobs GN 5435 star knobs are intended for use in hygiene areas. The sealed mounting surface enables fastening without dead spaces. The high quality finish and the large corner radii prevent adherence of dirt and facilitate cleaning.

View Complete Details

Ask Latest Price & Details

Stainless Steel-Cam Action Indexing Plungers

Stainless Steel-Cam action indexing plungers For GN 721.6 Stainless Steel-Cam action indexing plungers the indexing plunger pin is withdrawn by turning the lock by 180. For opposing cam action indexing plungers the left or right-handed types allow practical use, that is the same setting of the lock.

View Complete Details

Ask Latest Price & Details

Installation Kits

Installation kits The installation kits GN 491.1 are required for the attachment of a position indicator to double tube linear actuators. They consist of an adapter shaft and, depending on the position indicator, a torque support including fixing screws. For the position indicators DD52R-E DD51-E the respective rising is set at the position indicator for every programming.

View Complete Details

Ask Latest Price & Details

Oil Level Indicators

working temperature 100°C.

Oil level indicators with alcohol or detergents containing alcohol.The window consists of a continuous series of prisms which provide a clear and immediate reading of the level of the oil contained in the reservoir. The positioning of the packing ring in its housing guarantees a high tightening torque.

View Complete Details

Ask Latest Price & Details

Stainless Steel Pins

Material plastic
temperature resistant up to 80 °C

Knob Push button SlidePlastic, temperature resistant up to 80 CKnob: black-grey Push button: redPinStainless Steel AISI 303PawlStainless Steel AISI 304 (sheet metal)SpringStainless Steel AISI 301

View Complete Details

Ask Latest Price & Details

Breather Filters

temperature -30 °C to +100 °C

Breather filters GN 882 are used when the air exchange is to be allowed between the inside of the container and the ambient air. The filter function is marked by a blue colour ring.The filter prevents air-borne particles (e.g. dust) from being carried from the outside to the inside of the container. It also ensures that e.g. oil particles do not escape to the outside. The above diagram shows the air passage as a fact

View Complete Details

Ask Latest Price & Details

Lifting Eye Nut

The following guidelines of the lifting eye nuts DIN 582 have to be observed in addition to the load values given in the above table:The eye nut must be of fully screwd in to achieve a perfect contact between the two mating faces. Both threads must be of a equal length and the base material of equal strength to that of the nut. Operating instructions with more details and specifications are included with every delivery. The official DIN standard sheet specifies the additional sizes M42, M48, M56, M64, M72 x 6, M80 x 6 and M100 x 6.

View Complete Details

Ask Latest Price & Details

Pressed Steel

Pressed steel handwheels GN 227 have been specially developed for valves and they offer definite advantages:They consist of a single unwelded piece of pressed sheet metal manufactured by a special process to give a reinforced hub. They offer high mechanical strength and are not affected by shocks and knocks. They are resistant to temperature and fire and not weakened by any ageing process. The slightly tapered square hole allows easy installation and firm seating on a spindle.

View Complete Details

Ask Latest Price & Details

Hexagon Head Screws

Stainless Steel-Hexagon head screws GN 933.5 with brass or plastic pivots are used when pressure dents or damage to the clamping surface must be avoided. Stainless Steel-Hexagon head screws GN 933.5, type ZK, feature a spherical pivot whose diameter d4 is smaller than the core diameter d1 of the thread. This makes them suitable for holding thrust pads GN 631 GN 631.5 which must be ordered separately.

View Complete Details

Ask Latest Price & Details

Lifting Eye Bolt

The following guidelines for lifting eye bolts DIN 580 have to be observed in addition to the load values given in the above table:The eye bolt must be of fully screwed in to achieve a perfect contact between the two mating faces. Both threads must be of a equal length and the base material of equal strength to that of the bolt. Operating instructions with more details and specifications are included with every delivery. The official DIN standard sheet specifies the additional sizes M42, M48, M56, M64, M72 x 6, M80 x 6 and M100 x 6.

View Complete Details

Ask Latest Price & Details

Joints

Joints The permissible r.p.m. of universal joints with friction bearing DIN 808 is to a large extent dependent on the type of application such as load, duration, angular disposition as well as lubrication . For over 1000 r.p.m. universal joints with needle bearing should be used.

View Complete Details

Ask Latest Price & Details

Sealing Rings

quality 0.8 μm.

Sealing rings As delivered, or unassembled, the sealing rings haver the actual dimensions as stated in the table. To ensure a firm seating and reliable sealing, an installation space must be provided in the component as shown in the diagram. This ensures that when the sealing ring is installed, it will be subject to the necessary pressure without excess load. All surfaces which are in contact with the sealing ring should have a minimum surface quality of Ra 0.8 m.

View Complete Details

Ask Latest Price & Details

Stainless Steel-Nuts

temperature resistant -25 °C to + 150 °C

Stainless Steel-Nuts GN 1580 Stainless Steel-Nuts Stainless Steel-Screws are intended for use in hygiene areas. The sealed flange surface enables components to be mounted without dead spaces. The high quality finish as well as the large corner radii and closed surfaces prevent adherence of dirt and facilitate cleaning.

View Complete Details

Ask Latest Price & Details

Levelling Feet

Levelling feet The bottom seal protects the area beneath the foot plate from dirt. For this, the foot must be screwed on using the mounting holes and compressed accordingly. Hygienic fastenings and the correct position of the mounting holes are essential. The sealing ring above the adjustment sleeve enables fastening without dead space. Due to the wiper or the ball seal, the moving components are sealed against the environment.

View Complete Details

Ask Latest Price & Details

Edge Protection Seal Profiles

Edge protection seal profiles Edge protection seal profiles GN 2180 can be used to seal doors, covers and hatches. The profiles are pressed by hand onto the front of metal sheets and plates. The embedded clamp insert prevents detachment. Glue or other adhesives are not required.

View Complete Details

Ask Latest Price & Details

Cranked Handles

Cranked handles with retractable handle For tilting, the handle must first be pulled out of the taper in axial direction. A compression spring holds the handle in both end positions. When folded out, it automatically re-engages.

View Complete Details

Ask Latest Price & Details

Installation Brackets

Installation brackets Type A allows for the use of drilling templates specific to the application as well as fastening by welding. Type C installation brackets have one or two combinations of a hole and an elongated hole depending on the length l1.

View Complete Details

Ask Latest Price & Details

Stainless Steel-Locking Pins

Stainless Steel-Locking pins The locking balls are held in position by a pressure spring and are therefore not rigidly locked. The bolts can be quickly and easily inserted and removed from the locating hole. The rated shear stresses of the bolt cross-section are theoretical guide values only and do not constitute any warranty. They constitute no general warranty of quality and condition. The user must determine from case to case whether a product is suitable for the intended use.

View Complete Details

Ask Latest Price & Details

Linear Actuator Connectors

Linear actuator connectors The fixing bores for the follower are always located in the lid of the d1 bore andor the s1 square. Centering bushings in the through-hole eliminate the axial clearance. The width of the s1 square is dimensionally aligned with the play of the square linear actuators. The square s2 of the linear actuator connector is supplied not machined in the standard design.

View Complete Details

Ask Latest Price & Details

Slotted Locknuts

Slotted locknuts GN 1804.2 slotted locknuts with thread locking can be secured against twisting by twisting off the threaded shaft via a d4 set screw. The thread flanks of the nut ensure damage-free securing and can be used as often as needed.

View Complete Details

Ask Latest Price & Details

Stainless Steel-Retaining Washers

Stainless Steel-Retaining washers GN 2344 Stainless Steel-Retaining washers are universally usable standard parts. Type E is suitable for use in connection with retaining cables and ball chains to mount other standard or securing parts in order to prevent loss.Type L is suitable, for example, for mounting bolts or axes, which can thereby simultaneously be secured in an axial and also in a radial position.

View Complete Details

Ask Latest Price & Details

Stainless Steel-Assembly Pins

Stainless Steel-Assembly pins Depending on the requirement there are three washer types to choose from, which place the assembly pin in an axial position in its insertion direction. With the washer with eyelet (Type E) the assembly pin and a corresponding GN 1024 spring cotter pin can be secured to prevent loss using a retaining cable or ball chain. The washer with mounting shackle (Type L) simultaneously acts as loss protection and anti-rotation protection.

View Complete Details

Ask Latest Price & Details

Protective Guide Plates

Protective guide plates Protective guide plates GN 120.2 are used in connection with door latches, using the principle of friction. They prevent the latch from causing abrasion, for example to corrosion protection layers on a door frame. They additionally prevent unintended opening, as the latches lock into a small recess in their closed position.

View Complete Details

Ask Latest Price & Details

Stainless Steel-Thread Adapters

Stainless Steel-Thread adapters GN 480.8 thread adapters can attach e.g. air nozzles or coolant nozzles and their feed pipes with clamp mountings and hold them in position. The d2 thread diameters are compatible with the most common bolt diameters.

View Complete Details

Ask Latest Price & Details

Stainless Steel-Hose Adapters

Stainless Steel-Hose adapters GN 480.7 hose adapters can attach e.g. air nozzles or coolant nozzles and their feed pipes with clamp mountings and hold them in position. The d2 d3 thread and barbed fitting diameters are compatible with the most common bolt and internal hose diameters. Hose lines are attached to the barbed fitting with suitable hose clamps, securing them against slipping off.

View Complete Details

Ask Latest Price & Details

Stainless Steel-Strainer Fittings

temperature resistant up to 100 °C

Stainless Steel-Strainer fittings GN 7405 Stainless Steel-Strainer fittings are suited for assembly into piping systems as upstream or downstream protection devices. Depending on the mesh size, particles carried by liquid or gaseous media can be prevented from passing through. Units or housing interiors are thereby protected from foreign objects which can impair function or durability due to their size. The housing is separately bolted through a union nut, making assemblydisassembly easier and allowing the strainer insert to be exchanged if necessary.

View Complete Details

Ask Latest Price & Details

Stainless Steel-Mini Indexing Plungers

Stainless Steel-Mini indexing plungers Stainless Steel-Mini indexing plungers GN 822.9 are distinguished for their small dimensions. They are mounted by countersunk screws. The Stainless Steel-Mini indexing plungers present an affordable alternative to the GN 608.5 and GN 608.6 Stainless Steel-Indexing plungers. In types C and CN, the button can be turned by 30 after retracting the indexing pin, holding it in the retraced position using the indexing lock.

View Complete Details

Ask Latest Price & Details

Flanges

Flanges The GN 784.1 flanges are mounted from below onto the GN 784mounting clamps with swivel ball joint. A half-length tapered groove pin prevents any rotation. The half-length tapered groove pin is mounted on the flange. The countersunk screw is included separately.

View Complete Details

Ask Latest Price & Details

Swivel Ball Joints

Swivel ball joints GN 784 swivel ball joints allow precise and variable adjustment of the ball pivot within the rotation range. This is a particular advantage when adjusting scanners, cameras, lighting, monitors, etc. Thanks to the efficient clamping mechanism, only small amounts of torque on the clamping screw result in comparatively strong clamping pressure on the ball. This force is easily applied by the clamping lever (Identification no. 1).

View Complete Details

Ask Latest Price & Details

Stainless Steel-Ledge Handle

Stainless Steel-Ledge handle The GN 730.5 Stainless Steel-Ledge handle is used on doors, guards and hatches on machines, as well as on drawers and pull-out units. Due to the A4 material used, the handle is intended especially for use in corrosive environments with aggressive media. The ledge handle is made in a way that does not allow pooling of fluids, which makes cleaning easier and prevents build up of residue and bacteria.

View Complete Details

Ask Latest Price & Details

Two-way Clamp Mountings

Two-way clamp mountings The standard version of the clamping screw is a socket cap screw with hexagonal socket DIN 912. It can be replaced by a clamping kit GN 511 .

View Complete Details

Ask Latest Price & Details

Adhesive Discs

Adhesive discs After pulling off the protective film from the adhesive pad at the back, they can be attached to any suitable and clean surfaces. Adhesive discs GN 70.1 are used as counter piece for retaining magnets if a magnet is to be used on a non-magnetic surface, for instance.

View Complete Details

Ask Latest Price & Details

Swivel Clamp Connector Bases

Swivel clamp connector bases The center to center mounting hole distance m of the swivel clamp connector bases GN 485 matches the base plate clamp mountings GN 473, clamp mountings GN 477, flanged bolts GN 480 as well as retaining magnets GN 51.6. Swivel clamp connector bases GN 485 can be combined with swivel clamp mountings GN 482, T-swivel clamp mountings GN 483 and attachment clamp mountings GN 484 with the same k dimensions into swivel clamp mounting joints. Clamping kits GN 511.1 with screw (type S) and adjustable hand lever (type K) are available to connect the joints and bases (code no. for ordering is shown in the dimensional table).

View Complete Details

Ask Latest Price & Details

Stainless Steel-Clamping Lever Kits

Stainless Steel-Clamping lever kits The table of dimensions of the connector clamps shows the corresponding clamping kits for each clamping thread. The distance bushing is included part of the order.

View Complete Details

Ask Latest Price & Details

Angle Connector Clamps

Angle connector clamps The clamping bores of the Angle connector clamps GN 196 are specially designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462 respectively.

View Complete Details

Ask Latest Price & Details

Threaded Plugs

Threaded plugs The gaskets in types AC and AA correspond to the gaskets DIN 7603, zinc plated, nano-passivated, ultrasonically and tensile tested, Tensile strength class 5.8.

View Complete Details

Ask Latest Price & Details

Rubber Bumper Stops

Rubber bumper stops In terms of their dimensions, limit stops GN 2374 have been designed as extras for the GN 237 and family of hinges. They can also be bolt-attached when mounting the hinge, with an elastomer element limiting the angle of rotation to the value w. They are mainly used for lighter traps and gates, or when the limit stop is not expected to be exposed to dynamic loads.

View Complete Details

Ask Latest Price & Details

Tapped Holes Stainless Steel-Plates

Stainless Steel-Plates with tapped holes Dimensionally, Stainless Steel plates GN 2372 are designed as accessories for the GN 237 family of hinges, eliminating the need for nuts and washers for mounting. Meanwhile, there is no need for the time-consuming pre-assembly of washer and nuts or for counterholding during tightening. Mounted to the top side of the hinge, the plate offers entirely new assembly options.

View Complete Details

Ask Latest Price & Details

Safety Switch Hinges

Hinges without safety switch With the exception of the connector plug, the hinge without safety switch GN 139.6 do not differ in their external appearance from hinges with safety switch GN 139.5 .With the concealed screw connection at the back, the hinge is also tamper-proof. The compact design combines safety and attractive appearance.

View Complete Details

Ask Latest Price & Details

Stainless Steel-Levelling Feet

Stainless Steel-Levelling feet Stainless Steel-Levelling feet GN 23 will be delivered mounted and are not removable. Version W: with adjustable sleeve, hygienic Version, wrench flat at the bottom.

View Complete Details

Ask Latest Price & Details

Foot Plates

Foot plates Foot plates GN 6311.3 are used in connection with screws with pivots (grub screws DIN 6332 , tommy screws DIN 6304, DIN 6306). Owing to the special shape of immovable retaining ring, the foot plate is easily plugged into and removed from, the pivot.

View Complete Details

Ask Latest Price & Details

Fork Joints

Fork joints Fork joints GN 751.1 basically correspond to the fork head of DIN 71752 (Type A), but, unlike the DIN element, they have a rotating shaft and an additional bolt with axial shaft lock (Type KL and SL) which can be mounted and dismantled without tools. The rotating shaft allows non-dynamic radial movements to be compensated, movements which may occur e.g. when using cable winches. Also, there is no need for the otherwise necessary alignment of joint heads during assembly.

View Complete Details

Ask Latest Price & Details

Cam Point Screws

Cam point screws Cam point screws GN 418.2 are sturdy and compact elements, requiring a minimum of installation space and offering ultimate convenience and ease in handling. The clamping forces F given in the table refer to the maximum permitted tightening torque and the specified screw-in depth t.

View Complete Details

Ask Latest Price & Details

Guide Bushings

Guide bushings Guide bushings GN 179.1 with conical bore will be used for the latch bore of indexing plungers GN 817.5.

View Complete Details

Ask Latest Price & Details

Threaded Flanges

Threaded flanges Threaded flanges GN 3490 are used in connection with T-slot profile systems and allow elements to be assembled on or underneath the profiles, e.g. levelling feet. Depending on the threaded flange, thread size and thread depth dimensions that are available can exceed the dimensions of the profile groove.

View Complete Details

Ask Latest Price & Details

Levelling Disks

Levelling disks Washers Levelling disks GN 6343 are used mainly in mechanical engineering and jigmaking is required for levelling. chemically blackened surface.

View Complete Details

Ask Latest Price & Details

Cam Action Indexing Plungers

Cam action indexing plungers Cam action indexing plungers GN 612.10 are used in cases where the plunger must not protrude all the time. By rotating the lever through 180 the plunger withdraws itself. The groove allows safe positioning.

View Complete Details

Ask Latest Price & Details

Locators

Locators Locators GN 416.1 are matched to the spring latches GN 416 and are used to position the indexing pin. black, RAL 2005, textured finish.

View Complete Details

Ask Latest Price & Details

Stainless Steel-Retaining Rings

Stainless Steel-Retaining rings One typical application involves making e.g. knurled screws captive, for instance. Retaining rings GN 111.6 are normally used together with ball chains or retaining cables.

View Complete Details

Ask Latest Price & Details

Indexing Plungers

Indexing plungers Indexing plungers GN 414.1 with click-type safety lock are used when the plunger pin is to be briefly prevented from protruding. When the pin is retracted to its end position, the button engages with a clearly audible click. The safety lock can be unlocked only by exerting axial pressure on the red safety pushbutton, with the plunger pin then returning to its starting position by spring force.

View Complete Details

Ask Latest Price & Details

Other Products / Services #32437

Star Knobs

Stainless Steel-Cam Action Indexing Plungers

Installation Kits

Oil Level Indicators

Stainless Steel Pins

Breather Filters

Lifting Eye Nut

Pressed Steel

Hexagon Head Screws

Lifting Eye Bolt

Joints

Sealing Rings

Stainless Steel-Nuts

Levelling Feet

Edge Protection Seal Profiles

Cranked Handles

Installation Brackets

Stainless Steel-Locking Pins

Linear Actuator Connectors

Slotted Locknuts

Stainless Steel-Retaining Washers

Stainless Steel-Assembly Pins

Protective Guide Plates

Stainless Steel-Thread Adapters

Stainless Steel-Hose Adapters

Stainless Steel-Strainer Fittings

Stainless Steel-Mini Indexing Plungers

Flanges

Swivel Ball Joints

Stainless Steel-Ledge Handle

Two-way Clamp Mountings

Adhesive Discs

Swivel Clamp Connector Bases

Stainless Steel-Clamping Lever Kits

Angle Connector Clamps

Threaded Plugs

Rubber Bumper Stops

Tapped Holes Stainless Steel-Plates

Safety Switch Hinges

Stainless Steel-Levelling Feet

Foot Plates

Fork Joints

Cam Point Screws

Guide Bushings

Threaded Flanges

Levelling Disks

Cam Action Indexing Plungers

Locators

Stainless Steel-Retaining Rings

Indexing Plungers

Contact Us