Trumatic Engineers

Vatva, Ahmedabad, Gujarat

Guar Dehusking PlantConsist Following Machinery:

Cleaning, Splitter, Elevator, Pneumatic Conveyor, Centrifugal, Roaster, Dehusking, Cooler, Cone Mixer, Bagging, Rotary Siever, Ultrafine Pulverizer, Water Tank, Flaker Machine, pneumatic dryer line, conical blender.

Guar Dehusk Split Powder PlantConsist Following Machinery:

Mesh 200 300. Viscosity 3500 8000 cps elevator cleaning, store, double cone mixer, flaker, ultrafine grinder, dryer, siever, cone mixer, pneumatic conveyor, fan, cyclone, airlock, dust collector.

Guar Gum Split Plant Processfor grinding of guar splits is by ultrafine grinder without generating heat. They will be kept in dryer and will be blended before testing of soaked splits. Ultrafine Pulverizer helps to ground the flaked guar split.

FoodFeed& Spice Milling for grinding Marize , Wheat, Besan , Gralic, Onion, Chilley Sugar, Slot.

* We will design, develop, fabricate and install as per customer production capacity and quality requirement.

Technical Data sheet of Dies:

Roll shell can be supplied with either Standard (Dimpled) or Corrugated from Carbon Steel.

The manufacturing of wearing parts in the feed mill industry requires a thorough knowledge of raw material and Feed Mill Machinery. However to become an industry leader you have to do more. At Trumatic we do that extra steps. Not only do we meet established quality standards. We raise those standards by producing the highest quality Dies, Roll Shell and Beater possible.

METHOD OF WORKING
The entire stack of sieves is gyrated on a horizontal plane. Immediately the Feed spreads evenly over the top sieve. The rotary movement of the machine conveys the stock on the sieve and some of the finer particles fall through the screen onto the sieve collecting tray, to be discharged at right angles into one of the THROUGH channels. Thus material Travels overthe sieve and falls on the top of the next sieve below which similar size seperation takes place.
The coarse material or overtails continue to travel overthe remaining sieves, turning over and reversing their direction of flow as they pass from sieve to sieve, until it reaches the bottom sieve from where oversize is discharged as TAIL product. During the sieving operation, the mesh apertures are kept constantly open by the action of cleaners bouncing against the holes of the underside of each sieving surface.

The main machine components are the base frame, driving motor, counter weights, eccentric mechanism, sieve carrying frame, sieve stack, sieve clamping mechanism, and the sieve mountings.

The sieve stack frames are made of extruded aluminium sections braced to give extra strength. The sieve insert clothing frames are specially developed aluminium section braced across the centre by supporting platform of wire mesh for cleaning pads.

The Distinctive Principle of ULTRAFINE GRINDER is based on a high Air throughput in the Grinding area. This high Amount of Air is converted in to A Tremendous Turbulence by the Rotating & Stationary parts of the Machine as well as by an appropriate Guidance of the Air stream in the Mill.

The numerous Air Whirls in the Grinding chambers accelerate the Product up to the High Velocity of the Air. The Direction & The Speed of the particles is suddenly changed within extremely short periods. As a result of this principle the particles crash against each other so reaching a careful disintegration in high Air stream. A small percentage of grinding taking place by in pact with the rotating or stationary part of the Mill. The Creation of numerous air whirls in the single grinding chamber their increased turbulence by the inner grooved liner & the pulsation of the high air velocity make it Micronics.

Simple adjustment to the machine allow a narrow distribution range of out put particle our wet, Dry, Fibrous or Heat Sensitive materials.

No Foundation, Mechanically simple & Robust, operation & maintenance, No specialized personnel, Pneumatic Conveying of the Grind Product over 30-40 H height.

Vertical Type , Three Part.