Trumatic Engineers Ahmedabad, Gujarat

psyllium dehusking plant  consist following machinery: cleaning, rubber polisher, aspirator, siever, grader, fan, cyclone, dust collector. milling, pin mill, dehusking machine, husk separator, husk grader, pneumatic conveyor, husk cone mixer, baging. psyllium powder plant  consist following machinery: pin mill, hammer mill, roller mill, ultrafine grinder, fan, cyclone, siever, central fugal, pneumatic conveyor, powder cone mixer, baging, dust collector .

Roll shell can be supplied with either Standard (Dimpled) or Corrugated from Carbon Steel. Other Spares Hammer Beater   Elevator Top Rubberized Down & Bottom Case Puller Buckets. Molasses Mixer Beater. The manufacturing of wearing parts in the feed mill industry requires a thorough knowledge of raw material and Feed Mill Machinery. However to become an industry leader you have to do more. At Trumatic we do that extra steps. Not only do we meet established quality standards. We raise those standards by producing the highest quality Dies, Roll Shell and Beater possible.

APPLICATION The AMI Roto-sifter has high capacity yet physically small sifter unit used for seperation of various size fractions of particulate materials produced in the  Food, flour milling, feed, chemical pharmaceutical, plastics and similar processing industries. The machine is capable of making up to FOUR seperations with a variety of internal flow schemes and option of 4, 6 or 8 Frames for capacity. It is ideal for Hygienic Products and sieving of large quantities through fine apertures of Silk, Nylon, Polyester or Wire Mesh - Sieve Cloth. METHOD OF WORKING The entire stack of sieves is gyrated on a horizontal plane. Immediately the Feed spreads evenly over the top sieve. The rotary movement of the machine conveys the stock on the sieve and some of the finer particles fall through the screen onto the sieve collecting tray, to be discharged at right angles into one of the THROUGH channels. Thus material Travels overthe sieve and falls on the top of the next sieve below which similar size seperation takes place. The coarse material or overtails continue to travel overthe remaining sieves, turning over and reversing their direction of flow as they pass from sieve to sieve, until it reaches the bottom sieve from where oversize is discharged as TAIL product. During the sieving operation, the mesh apertures are kept constantly open by the action of cleaners bouncing against the holes of the underside of each sieving surface. CONSTRUCTION The main machine components are the base frame, driving motor, counter weights, eccentric mechanism, sieve carrying frame, sieve stack, sieve clamping mechanism, and the sieve mountings. The sieve stack frames are made of extruded aluminium sections braced to give extra strength. The sieve insert clothing frames are specially developed aluminium section braced across the centre by supporting platform of wire mesh for cleaning pads. INSTALLATION The AMI Roto-sifter is delivered as a fully assembled Unit. Installation involves only bolting the machine to a firm foundation, cutting holes in floor for deliveries, making the electrical connections and finally fixing up the inlets and outlets and required size sieve clothes to start the production.   FEATURES :     Simple in Construction. smooth, noiseless running. Extremely high capacity. Positively leak proof method of clamping . Handy, interchanfable sieves and loose clothing frames. Great adptability to suit rewuirement of flow, no.of separations, sieves etc. Minimum time required for attendance and cleaning. Easy and rapid installation. ldeal for hygienic Products. Provides aseptic condition.

    The Distinctive Principle of ULTRAFINE GRINDER is based on a high Air throughput in the Grinding area. This high Amount of Air is converted in to A Tremendous Turbulence by the Rotating & Stationary parts of the Machine as well as by an appropriate Guidance of the Air stream in the Mill. The numerous Air Whirls in the Grinding chambers accelerate the Product up to the High Velocity of the Air. The Direction & The Speed of the particles is suddenly changed within extremely short periods. As a result of this principle the particles crash against each other so reaching a careful disintegration in high Air stream. A small percentage of grinding taking place by in pact with the rotating or stationary part of the Mill.. The Creation of numerous air whirls in the single grinding chamber their increased turbulence by the inner grooved liner & the pulsation of the high air velocity make it Micronics. Simple adjustment to the machine allow a narrow distribution range of out put particle our wet, Dry, Fibrous or Heat Sensitive materials. Operation (Maintenance - Installation): No Foundation, Mechanically simple & Robust, operation & maintenance, No specialized personnel, Pneumatic Conveying of the Grind Product over 30-40 H height. PRODUCTS CURRENTLY BEING GROUND Grinder for Powders Tyre Rubber Wheat-Whole Atta Grinding Pharmaceuticals Carbon Block Carbonate Wood Flour Grinding Grinding of Cosmetic Sugar Dextrose Polypropylene Bentonite Cocoa Press Pigment Grinding Polyesters Grinder for Guar Gum Adhesives Grinder for Asphalt Tamarind Flour Grinder for Dyes Chemicals Chicory Clays Grinding of Psyllium Cereal & Other Milling Product Salt Animal Feeding Stuff Grinder Talc Calcium Fish Grinding Standard Models: Vertical Type , Three Part. Model     H.P Cap- Kg/Hour Wheat Guar T-5 5-10 150 10 T-15 15-30 400 40 T-25 50-75 800 80 T-50 75-100 1500 150 T-100 100-120 2000 200 T-110 120-180 2500 250 T-200 200-250 5000 500

Pellet Mill has a higher output per capital cost than any other pelleting machine on the market Pellet Mill has easy maintenance Pellet Mill is designed for silent smooth running Pellet Mill is meticulously engineered Long accumulated experience has gone into the Trumatic which is built to suit Dairy, Poultry Feed, Hog Feed, Oil Seed, Corn Wet Milling, Fish standard for continuous operation. This can be installed in an existing plant. The capacity depends on hole diameter of die, pellet thickness, speed of rotation. It's incorporate refinements are not found in any other pellet mill. Consists: Variable feeder, feed conditioner, permanent magnet, adjustable pellet cutter, oven loading mechanical fuse, easily operatable guard, big fly wheel, die holder assly., roll assly.   Pellet Mill Specifications: No.     Die Roll Output K.W. 1 305 x 110 148 50 2 420 x 160 205 110 3 520 x 190 250 160 4 660 x 190 302 200 5 850 x 295 390 250 6 900 x 295 408 250 Die Speed   from 3.5 m/sec.  

Technical Data sheet of Dies: We produce Die For Buhzer, Matador Van Arsen , Cpm. Pazadin , Mabrik. We produce Ring ad Flat dies suitable for all models of pelletising mill used for Feed Mill, Chemical, Fertilizer waste, Wood and Plastic. Dies made from Alloy, Chromsteel (S.S) or special steel, Dies are hardened temped, mirror polish to get economical output from your Pellet Mill.