Tiru Embedded India Pvt. Ltd.

Gondal, Rajkot, Gujarat

We are involved in supplying a broad array of gps trainer which is highly acknowledged in the market for its high performance and long service life. Our offered array is developed and created using top notch quality components and high end technology in accordance with international quality norms and standards. Features: - high functionality-rugged-smooth finish technical specifications: - l1 frequency, ca code, 51- channel high sensitivity-cold start, warm start, hot start-max. Update rate: 5 hz (default: 1 hz)-built in rs 232 level converter (max 232) provided in 9 pin d type connector-windows based software support gps status, signal level, sky chart constellation of sv

We are offering lily pad simple snap.The lilypad arduino simplesnap is a microcontroller board designed for wearables and e-textiles. It is similar to the lilypad arduino simple, except that it has a built in lithium polymer battery, and instead of through-holes, it has conductive snaps. By using matching snaps in your project, you can affix the lilypad securely but remove it to wash your project or move it to another project. The lilypad simplesnap has 9 pins for input & output. Additionally, it has a built in charging circuit for the battery. The board is based on the atmega328. The lilypad arduino simplesnap was designed and developed by leah buechley and sparkfun electronics.

We are offering lily pad usb.The lilypad arduino usb is a microcontroller board based on the atmega32u4 (datasheet). It has 9 digital inputoutput pins (of which 4 can be used as pwm outputs and 4 as analog inputs), an 8 mhz resonator, a micro usb connection, a jst connector for a 3.7v lipo battery, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a usb cable or power it with a battery to get started. The lilypad arduino usb differs from previous lilypad boards in that the atmega32u4 has built-in usb communication, eliminating the need for a separate usb-to-serial adapter. This allows the lilypad arduino usb to appear to a connected computer as a mouse and keyboard, in addition to a virtual (cdc) serial & com port.

We are offering 4ch sd card -h.264 compression vehicle mobile dvr. Model:wp-bw1000 description:4-way audio and video input resolution d1hd1cif optionalh.264 video compression, linux operating system, dual-streamthe digital watermarking functional dual sd card storage, single card to support a maximum capacity of 32gbbuilt-in gps module optionaldynamic detection 8 seconds delay the power data protection, prevent momentary power failure caused the loss of data and storage of file corruptionrich peripheral interfaces, such as: rs485, rs232, differential speed interfacecar black box function, recording speed, position, momentum, acceleration, temperature, brake, reverse, turn, alarm and other important information.dc8v 36v wide voltage power supply, the industry standard embedded design, metal aluminum casing, low power operating temperature -25 to +85

The Arduino Ethernet is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input & output pins, 6 analog inputs, a 16 MHz crystal oscillator, a RJ45 connection, a power jack, an ICSP header, and a reset button.NB: Pins 10, 11, 12 and 13 are reserved for interfacing with the Ethernet module and should not be used otherwise. This reduces the number of available pins to 9, with 4 available as PWM outputs. An optional Power over Ethernet module can be added to the board as well. The Ethernet differs from other boards in that it does not have an onboard USB-to-serial driver chip, but has a Wiznet Ethernet interface. This is the same interface found on the Ethernet shield. An onboard microSD card reader, which can be used to store files for serving over the network, is accessible through the SD Library. Pin 10 is reserved for the Wiznet interface, SS for the SD card is on Pin 4. The 6-pin serial programming header is compatible with the USB Serial adapter and also with the FTDI USB cables or with Sparkfun and Adafruit FTDI-style basic USB-to-serial breakout boards. It features support for automatic reset, allowing sketches to be uploaded without pressing the reset button on the board. When plugged into a USB to Serial adapter, the Arduino Ethernet is powered from the adapter. The Revision 3 of the board introduces the standardized 1.0 pinout, that consist in: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, this will the opportunity to shield that use i2c or TWI components to be compatible with all the Arduino boards;the IOREF that allow the shields to adapt to the voltage provided from the board. Shields that use the IOREF pin will be compatible both with the board that use the AVR, which operate with 5V and with the Arduino Due that operate with 3.3V. Next to the IOREF pin there is a not connected pin, that is reserved for future purposes.

We are offering 4ch hdd -h.264 compression vehicle mobile dvr. Support 2.5 inches large capacity hard disk storage, the highest support 2 ch d1 video record, applicable to need large capacity storage video client 4channel videoaudio input, d1hd1cif adjustable;h.264 video compression, linux operation system, dual streaming;digital watermark;acceleration statistics;unique patent in anti-vibration. 6pin connector for hdd housing and mainborad to ensure stable working in complex condition with vibration;hard disk auto-heating;3g(wcdmaevdo) wifi gps mudules optional ;motion detection;storage: 1tb hdd(2.5 inch)+32gb sd card;8 seconds power-off delay for data protection, in order to prevent data lost and file destroyed by instant power-off;multiplex interface, one sd card slot, 1 usb interface, 6 alarm input, 2 alarm output, 2 rs485, 1 rs 232 etc.;support extra external device, such as intercom, control pannle etc.;black box for vehicles, recording speed, position acceleration, temperature brakes, backing up, turns, alarms and other important information;dc8v to 36v wide range voltage power supply, embedded design in industrial standard, aluminum metal housing, low power consumption;operation temperature -25to +85

We are offering 4ch dual sd card -h.264 compression vehicle mobile dvr. Model:wp-cw1000 description: 4-way audio and video input resolution d1hd1cif optionalh.264 video compression, linux operating system, dual-streamthe digital watermarking functionaldual sd card storage, single card to support a maximum capacity of 64gbbuilt-in gps module optionaldynamic detection8 seconds delay the power data protection, prevent momentary power failure caused the loss of data and storage of file corruptionrich peripheral interfaces, such as: rs485, rs232, differential speed interfacecar black box function, recording speed, position, momentum, acceleration, temperature, brake, reverse, turn, alarm and other important information.dc8v 36v wide voltage power supply, the industry standard embedded design, metal aluminum casing, low poweroperating temperature -25 to +85

We are offering arduino mega. The arduino mega 2560 is a microcontroller board based on the atmega2560 (datasheet). It has 54 digital inputoutput pins (of which 15 can be used as pwm outputs), 16 analog inputs, 4 uarts (hardware serial ports), a 16 mhz crystal oscillator, a usb connection, a power jack, an icsp header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a usb cable or power it with a ac-to-dc adapter or battery to get started. The mega is compatible with most shields designed for the arduino duemilanove or diecimila. The mega 2560 is an update to the arduino mega, which it replaces. The mega2560 differs from all preceding boards in that it does not use the ftdi usb-to-serial driver chip. Instead, it features the atmega16u2 (atmega8u2 in the revision 1 and revision 2 boards) programmed as a usb-to-serial converter.Revision 2 of the mega2560 board has a resistor pulling the 8u2 hwb line to ground, making it easier to put into dfu mode. Revision 3 of the board has the following new features: 1.0 pinout: added sda and scl pins that are near to the aref pin and two other new pins placed near to the reset pin, the ioref that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible both with the board that use the avr, which operate with 5v and with the arduino due that operate with 3.3v. The second one is a not connected pin, that is reserved for future purposes.stronger reset circuit.atmega 16u2 replace the 8u2.

We are offering lily pad simple.The lilypad arduino simple is a microcontroller board designed for wearables and e-textiles. It can be sewn to fabric and similarly mounted power supplies, sensors and actuators with conductive thread. Unlike the lilypad arduino main board, the lilypad simple has only 9 pins for input & output. Additionally, it has a jst connector and a built in charging circuit for lithium polymer batteries. The board is based on the atmega328. The lilypad arduino simple was designed and developed by leah buechley and sparkfun electronics.

We have 3 years of experience in the Embedded Industry.We are giving the training as we ll as we are making the project for the college student of the Electronics & Communication Branch.