Tiny Controls (p) Limited

Kakrola, Delhi

we are offering spindle motor holder. spindle motor holder for spindle motors with diameter 65 mm.

we are offering spindle motor clamp.fixture of 100mm diameter for the spindle motors.

we are offering spindle clamp.spindle motor holder for 80mm diameter spindle motors.

We are offering cnc control box kit - 1 . Kit includes : empty cabinet in sheet metal power coated inside and outsideall mounting holes are already punchedmains socket :1 pcmains cable : 1 pc6a fuse : 2 nos220v cooling fan : 1 pcfan guard (jaali) : 1 pc4 pin motor connectors : 4 male + 4 female6 pin signal connectors : 4 male + 4 female220v indicator : 1 pcmains switch 16a : 1 pcemergency switch with 1 no and 1 nc contacts each

We are offering tnc-m13 cnc controller box. Specifications of cnc controller box: tnc-m13 cnc controller board for cnc machining with handheld pendant.3 stepper drives for 3 axes. Two options for stepper drives are available:drive 087 generates 1.2-7.0 a phase current.Drive 484 generates 0.7-4.2 a phase current.Power supply: transformer + tl-psb1 linear power supply board. Following options are available for the transformers:option 1: 42v, 10a toroidal-crgo transformer with transformer rating 300va continuous.Option 2: 60v, 12.5a toroidal-crgo transformer with transformer rating 500va continuous.Usb host port:usb 2.0 port.Communication terminals:serial terminal for pendant interfacing.Serial terminal (for plc interfacing).Operating interface: external connectors for connections.Inputs connectors:home input connector: 1.Limit input connector: 1.Misc inputs (tool zero, block mode, start-stop, hold resume) connector: 1outputs connectors:axes outputs connectors: 3.Spindle output (vfd output) connector: 1.Coolants output: 1220v power indicator: 1.Emergency switch: 1supply voltage: 220v.Fuse: 2a.Dimensions: 400x400x130 (in mm).Weight: 15 kg approx.

We are offering cnc mach3 control bo. Specifications of mach3 control panel: pp-bob2-v1 breakout board for cnc machining.3 stepper drives for 3 axes. Two options for stepper drives are available:drive 087 generates 1.2-7.0 a phase current.Drive 484 generates 0.7-4.2 a phase current.Power supply: transformer + tl-psb1 linear power supply board. Following options are available for the transformers:option 1: 42v, 10a toroidal-crgo transformer with transformer rating 300va continuous.Option 2: 60v, 12.5a toroidal-crgo transformer with transformer rating 500va continuous.Communication terminals:serial terminal for interfacing breakout board with relevant cnc controlling pc based software.Operating interface: external connectors for connections.Inputs connectors:number of input connector: 1.Number of inputs: 4.Emergency input: 1outputs connectors:axes outputs connectors: 3 for 3 axes motion control, step and direction output.Spindle output (vfd output) connector: 1.Coolants relay connector: 1220v power indicator: 1.Emergency switch: 1supply voltage: 220v.Fuse: 2a.Dimensions: 400x400x130 (in mm).Weight: 15 kg approx.

we are offering Cnc Controller, CNC motion controller is a G-code programmable controller with step and direction outputs for stepper drivers. In addition to 3 axes, Y slave is also added to system for gantry type machines. All axes can be configured with independent adjustable maximum velocity and acceleration. Contact at 09911193210 for more details.Features:Totally independent single board solution.32 digital + 2 analog outputs + 1 isolated analog output + 3 relay outputs.19 opto-isolated inputs.Low jitter 150 KHz Pulse rate on each axis.Constant velocity (with look ahead) and exact stop path modes.Interpolation linear, arc and helical.Work offset (Work Coordinates).Feed override option (Feed and Spindle speed).Tool offset option (Auto Tool Offset measurement).Jogging via inbuilt keypad (Step, Continuous and Fast mode).Feed hold (pause), Cycle start (and cycle resume), Cycle stop (abort).Home and limit inputs for all axes (can be individually enableddisabled).Block execution mode (menu run time control).Controlled feed hold with deceleration to ensure no skipped steps and loss of location.G-code check option (Dry Run) and program limit check function.Screw terminal connectors for connecting motor drive, input and outputs.Help menu handy for first time users.Handheld Pendant to display statussettings and control the machine.Intuitive menus with easy to use smooth navigation.Inputs for Limit and Home switches (or sensors).Emergency Stop switch on handheld unit.

We are offering parallel port break-out board (pp-bob2-v1). Features : all the inputs are optoisolated, filtered and buffered for noise immunity. all the outputs are buffered and taken out to screw terminals. selection of pullup or pull-down for motor outputs. all outputs and inputs have led indicators for easy diagnostics. motor output common terminal can be selected as 0v or 5v. on board pwm to 0-10v circuit for spindle speed control from program. db25 as well as 26 pin frc connectors. frc to db25 cable is available as an option, allowing clean layout in control box and get db25 connector out from control box. on board charge pump circuit is provided for safety. on axis ( step and dir ) signals are buffered twice and taken out to terminals enabling hardware slaving of 2 motors on one axis need for gantary style machines. three on board relay provided for spindle or auxillary on off control. made in india

We are offering breakout board cnc mach emc2 kcam. Standard db25 m-m cable is included with boardfeatures: all buffered outputs are taken out to screw terminals.all the inputs are optoisolated, filtered and buffered for noise immunity.all inputs or outputs like estop, chargepump, relays can be reclaimed and used for any purpose with jumpers.on board rectifier and filter, accepts 9v to 15v ac or dc input for power.on inputs, both terminals of optoisolator are connected to screw terminals, providing flexible connection to source sink type inputs and with external series resistor can tke from 5v to 24v inputs.26 pins frc as well as db 25 connectors.an on board charge pumo for safety is provided.for enabling the hardware slavage of 2 motors on one axis for gantary style machines; one axis outputs i.e. Step and dir are buffered twice and taken out control box to terminals.for spindle and auxillary on-off control, an on board relay is given improve flexibility further.hand made high quality, low resistance, shielded male-to-male parallel port cable included.led indicators provided - power ok, estop ok, relay on and chargepump ok signals.made in india

we are offering reduction gear assembly. reduction gear assembly for nema 34 motor modular design.designed for nema 34 motors.shaft size of the big pulley is 15 mm diameter which is sufficient for most modern transfer requirements.4:1 reduction.1.5 module pinion standard.pulley with 0.5 bore supplied for motor.

Features of stepper driver tstep-484: a perfect micro stepping drive by using sinusoidal current for an accurate motion. Tstep 484 can drive motor with which can run on 20v-48v rated voltage and 4a rated current. Jumper selectable drive current for driving range of stepper motor. Opto isolated step and direction inputs and error outputs. When the motor is stopped, there is less motor heating with automatic current reductions. Drive is very compact and less installation space is required. Maximum torque is achieved at high rotational speed by automatic current compensation usage. Smooth motion without resonance. The drive is versatile and can be used with a range of stepping motors. Protection from short circuit. You can use drive with 4, 6 and 8 lead steppers in bipolar series, in half coil or parallel configurations. Made in india stepper drive specification series model : tstep-484 rated voltage : 18v-48v rated current : jumper selectable 0.7a to 4.2a micro stepping : yes idle current reduction : yes short circuit protection : yes isolated step dir inputs : yes

Cable drag chains are the umbilical cord of modern machines. Drag chains are the convenient as well as a perfect way to route the wires of your CNC machines. They minimize downtime, protect, support and extend the service life of cables and hoses. Today, cable tracks are widely used for machine tools equipped for numerical control machines, electronic equipments and CNCs. Plastic drag chains can be used for horizontal, vertical or combined horizontal- vertical wires housing applications. Based on standard norms, they are highly durable, customized and easy to install. These wire resistant cables have support high speed movement. These require low maintenance and produce less noise.

With a rich experience of spindle motors, Tiny Controls provide High Speed Air Cooled Water Cooled Spindles for precised CNC engraving and CNC wood routing. Wide range of Air Cooled High Speed Spindle Motors is available with us and is in accordance with set industrial standards. High overload capabilities and high operation speed range are distinctive features of our Spindle Motors offering exceptional dynamic performance. Other features include superior quality, enhanced reliability, smooth motion and balancing stability. The spindles are capable of completing very complex tasks very easily. Machined Spindle Holders for securing spindle on CNC machines are also available. Range of Air Cooled High Speed Spindle Motors to choose from and Optional Spindle Holders machined in Aluminum are available for spindles on request, at extra cost. Variable Frequency Drivers are needed for three Phase Motors and not included in prices mentioned.

We are offering stepper motors. high quality, highly accurate and compact stepper motor with length 38 mm, dia of 42 mm and 4 lead wires.

Hot Foil Stamper is a programmable controller intended to control the Hot Foil stamping machines. It can control three motors with independent parameter setting for each like motor speed, acceleration; steps per mm etc are independently configurable. 20x4 alphanumeric LCD for settings and status display.Easy to use menus and smooth navigation.16-bit controller with 32-bit math for precision.Opto-isolated pulse input for easy connection to external signal.Configurable micro-step settings.Low Jitter pulse train on three motor outputs simultaneously.

Highly efficient and precise hybrid stepper having length 47 mm, diameter 42 mm and 4 lead wires.Temperature Rise : 80C Max.(rated current, 2 phase on)Ambient Temperature : -20C +50CInsulation Resistance : 100 M O Min. , 500V DCDielectric Strength : 500V AC for one minuteShaft Radial Play : 0.02 Max. (450 g-load)Shaft Axial Play : 0.08 Max. (4200 N ( 20 mm from the Flange )50 g-load)Max. radial force : 60 N

Two phase steppers come with 4, 6 or 8 wires (motors with 8 leads have two separate windings per phase). All these motors can be wired in bipolar mode while 8 wire motors can be wired in unipolar or bipolar modes. Our range of 2-phase motors is available with both 4-leads and 8-leads. To learn more details on how to connect these with a bipolar stepper driver, please click on the tutorial in Help Section.The high torque hybrid bipolar stepper motors feature low inductance for high speed to driving voltage ratio and good linearity for perfect microstepping. A perfect match to our microstepping step drivers range includes Nema 12, Nema 14, Nema 17, Nema 23, Nema 34 and Nema 42 motors.

We are supplier and exporter of this product.

We are supplier and exporter of this product.

We are offering Stepper Motor Driver. Features of Stepper Driver Tstep-087: Precise micro-stepping driver using sinusoidal current for accurate motion. Bipolar Driver can drive motors at 20V-80V and 7A depending on the model Driver current is Jumper selectable for driving range of stepper motors. Driver has opto-isolated StepDirection Inputs and Error output. Low stepper motor heating with automatic current reduction while motor is stopped Very compact design so that drivers require less space in control box or panels. Our drives uses automatic current compensation to achieve maximum torque at high rotation speeds. Smooth motion without any resonance or vibrations. Versatile drive design capable of driving range of stepper motors. Short circuit protection Driver can be used with 4, 6 or 8 lead stepper motors in bipolar Series, Half Coil or Parallel configurations. Made in India User manual: http:www.tinycontrols.comdatasheetsTstep-087.pdf Stepper Drive Specification Series Model : Tstep-087 Rated Voltage : 18V-80V Rated Current : Jumper selectable 1.2A to 7.0A Micro stepping: Yes Idle Current Reduction : Yes Short Circuit Protection : Yes Isolated Step Dir Inputs : Yes