THUNDER AUTO LLP

Pappanaickenpalayam, Coimbatore, Tamil Nadu

Our Thunder Auto's Mechanical creeper is a three in one automation tool. The Mechanical creeper can act as a bench, Creeper and dashboard servicing tool. The multiple access of this tool provides an extreme

• Suitable for Mechanical Bays, Body Shops, Tyre Shops, Car Spa's and accessories shops
• Comfort to the technician, results ease for a long job and reaps quality output
• Design of the frame evenly distribute weight and also adds balance with comfort to the technician
• Cushion seats provides an extreme comfort for day to day work
• Options to convert to creeper, Bench or a Dash board creeper
• Powder coated frames and angles for a longer life
• Heavy duty four Swivel wheels for longer life and smooth mobility

Our Knee Trolley promotes a unique kneeling position that reduces pressure on your lower back, and the hip / Chest rest which can be adjusted and tilted to provide multiple postures which results in an ultimate support and comfort in your day to day garage works.

• Suitable for Mechanical Bays, Body Shops, Tyre Shops, Car Spa's and accessories shops
• Comfort to the technician, results ease for a long job and reaps quality output
• Design of the frame evenly distribute weight and also adds balance with comfort to the technician
• Cushion seats for knee rest and the hip / Chest rest provides ultimate comfort
• Cost effective tool for current automobile servicing sector
• Unique kneeling position reduces pressure on lower back
• Powder coated frames and angles for a longer life
• Heavy duty Three Caster wheels for longer life and smooth mobility

Accessory to be used as an engine or general lift. This includes additional load balancing for your lifts by attaching leg extensions.
Weight limit: 350kg

Accessory to be used to support vehicle after lifting and before any work is performed.

Used to safely lift on grated floors, such as in down draft spray booths.

Tool that helps in supporting our lift, where the surface of the service centres ground or the floor is uneven

KOCH-ACHSMESSANLAGEN manufactures since more than 50 years wheel alignment systems. At the beginning the simple mechanical measurement systems were replaced by modern laser wheel alignment systems with best references of well-known vehicle manufactures and more than thousands of work shops in all over the world.

The wheel alignment producer KOCH-ACHSMESSANLAGEN offers a big range of wheel alignment systems which are produced specially for all different kind of vehicles - whether passenger car, van, bus, truck, agricultural machinery, tractor, semi-trailer or trailer. The name Koch-wheel alignment is standing for best quality and service with highest accuracy and guarantee quick and easy handling.

• Available for the 4-wheel alignment of passenger cars, vans and pick-ups
• Lifting of the vehicle is not necessary axle in driving condition
• Easy use and quick measurement
• The floor and the lifting platforms have not to be 100 % horizontal
• All measurements within 10 minutes including set-up time
• New inclinometer (digital electronic protractor) for the measurement of camber, castor & KPI
• Easy mounting on every wheel
• It is fit for every rims till 22 inch if desired also till 32 inch (special order)
• Print-out of the measuring record with CD (included delivery content)
• 360 turnable laser head
• Quick measurement of: total and single toe, camber, castor, KPI, turning radius, central position of steering Wheel, rear axle offset
• run-out compensation on request
• The very good price-performance ratio assures a quick amortisation

Thunder Profimaster 3000 Universal Jack is a mobile lifting solution, which can be used as single or in systems with 2 0r 4 columns.

The Thunder Profimaster can be used for lifting Car, Off-road Car, SUV and MUVs.

A.The system consists of a single column, electrical components to be connected only to the users power outlet.

B. Electrical Components
1. A single phase motor of 1.1kW at 1440 rpm for 220V (high starting torque).
2. Reversing switch of three poles with a bridge for single-phase installation of 12 amps with return-tozero.
3. Connecting cables:
a. Power feeding cable RV-K 3 x 1.5 mm (2 m long)
b. Connection switch-motor with the cable RV-K 5 x 1 mm (0.50 m long)

C. Attachments The Components used with this unit to accomplish a variety of uses