Tempsens Instruments (I) Pvt. Ltd.

Madri, Udaipur, Rajasthan

lt is impossible to have dependable production without quality management. The expectation is growing and customers requirements must be addressed. In most of the industries, proper monitoring of temperature with time plays an important role in the quality of products. Whether it can be painted/powder coating industries, oven manufactures, automobile industries, and many more.
At Tempsens, we have indigenously developed a thermal profiling system, consist of a Data Logger with a Thermal Barrier Box. The data is collected and stored in the data logger. While the Thermal barrier protects the electronics of the data logger from the prevailing temperature in the oven/furnace.

Key Features :

• Maximum temperature can be reached upto 950°C.
• Stainless steel casing provides resistance to oxidation at high temperatures.
• Replaceable wear strips to minimize maintenance costs.
• To avoid thermal stresses, rounded edge barriers are designed.

Accessories:

• Software
• Thermocouple
• Operation Manual

For any Production/process facility, when a large volume of fluid to be heated before pumping out to process application, the Immersion Heaters are always the best-recommended solutions. A single bundle or multiple smaller units can be installed in the Tank for the uniform heat transfer and steady heating of the fluid with all safety precautions in built within the heater and control system.
Some of the precautions to be taken while designing and selecting an Immersion heater are

• Selection of right material for the wet parts to avoid potential corrosion from the fluid to be heated.
• Proper cold length & active length ratio to avoid hot spots & dry heating.
• Element skin temperature within flash point limit of the fluid to avoid any hazard. A Proper thermal design is very much necessary whenever heating a flammable fluid or in hazardous area installation.
• Fixing method & support for the bundle considering the turbulence during the in & outflow.
• Control system for both element skin & fluid temperature.

ConstructionTerminal Enclosure: Marathon flameproof heaters are certified to install in hazardous area Zone 1 & 2 , Gas group IIC, IP66. The Terminal enclosure is designed to protect the terminals of the individual elements from external impacts, such as dust, moisture etc and to facilitate the connection of the Incoming power supply to the heater bundle.
Heater Bundle: Consist of No. of U Pin heating elements adequately supported by set of Baffles & Tie rods, designed to deliver the specified temperature at outlet by maintaining the element temperature & pressure drop within the safe limits. Heating elements can be fixed to heater flange by means of standoff sleeve pipes with brazing or by direct welding or by means of threaded couplings. Heat duty of a bundle can be divided in to many sub groups (banks) based on process conditions. This will help in better control as flexibility in the operation.
Temperature Sensors: The Heater bundle will have Element skin temperature sensor for monitoring and regulating the Element skin temperature within the limits. The Unit may also need additional sensors such as Tube sheet Temperature Sensor, Terminal Box Sensor, vessel Body temperature sensor and process fluid Temperature sensors based on case to case. The Sensors used for the system will be certified in accordance with the area of installation. The Temperature sensors are Typically RTD or Thermocouple. A simple heater bundle can also be controlled using Thermostat protection for skin & process temperature. If the Operation pressure is High, It is recommended to have a PSV (Pressure safety Valve) installed within the Heater Vessel as an additional safety measure.
Control Panel: Heater controls Panel are designed to monitor & control the operations of the heater bundle also to ensure the safety of the equipment and operations. The control logic can be either ON/OFF (contactor) or regulated (Thyristor) or combination of both in a single panel. The control panels can be installed in both safe area & hazardous area by following respective design guidelines & certification requirements. The Control Panels are provided with various indication systems such as Power ON, Heater ON OFF, Trip, High Temperature etc for comfortable handling of the process. The Temperatures of Elements, Process fluid & other areas (with sensors) are displayed on the Panel for better monitoring & awareness. Control Panel will also have safety interlocks such as high element temperature, Earth fault, process over temperature etc along with Emergency stop access for the safe operation and control.

Advantages

• Heaters can be used for quick heating of small volume storages as well as for heating large volumes with longer operational hours
• Widely used for heating high viscous fluids ( Bitumen, HFO etc) and reduce the viscosity before pumping out
• Environment-friendly design. No hazardous gas/smoke/ emission from the system.
• Precision Temperature control
• Can be accommodated in small footprints.
• Custom designed to meet specifications.
• Highly energy efficient and provide maximum dielectric strength.
• Compatible with standard industry piping and safety standards.
• Reliable design.
• Easy to operate and maintenance-friendly.
• Energy Saving.
• No need to drain the tank for any repair/replacements in case of indirect Immersion Heaters.
• Heating Elements: Mineral filled insulated Heating Elements or Tubular heating Elements with Ni-Cr (80-20) as heating Coil and suitable outer sheaths.
• Protections & control: Element Skin Temperature Control, Process Temperature Control, Earth Leakage Protection Overload Current Protection, Temperature Class Protection ( for Hazardous area only)

Application

• At large Storage Tanks for preheating of thick fluids.
• Oil Heating (crude, Thermic fluids, and other Process fluids etc in storage tanks).
• Water heating applications & vaporizer System.
• For reducing the viscosity of the fluid and make it suitable for pumping out.
• Steam Boilers.
• Oil cooling systems & compression packages
• Edible oil heating for food industries.

Tempsens offer Air Heaters which features high-temperature resistance wire open coil which is electrically isolated in a stainless steel sheath. Because the air being heated passes directly over the resistance wire, maximum heat transfer efficiency is achieved.
Air Heaters are used for heat staking, plastic welding, laminating, drying, heat sealing, and any other operation where air needs to be heated up 500C.

Advantages

• Fast heat uptime
• Increased Efficiency
• Easy installation
• Easy and inexpensive replacement

Construction

• Nickel chromium Resistance wire coils for maximum heater life evenly wounded for even heat distribution
• Mica Sheet for holding coils in place and are dielectric, lightweight, resilient and stable high temperatures.
• Mica Insulation having dielectric property to isolate high resistance coil from the sheath.
• Stainless Steel Sheath for corrosion resistance and high strength.
• Teflon coated control cable & thermistor cable for superior insulation and suitable for high voltage application.
• Glass wool insulation for high thermal resistance with low thermal conductivity.

Coil heaters offer high heating profile and high performance in compact spaces up to temperatures as high as 750°C. Available in Various cross-sections and sizes, coil heaters are not only straight and coil form but can be formed into almost in any geometrical shape.
Coil heaters can be closely wound to provide concentrated heat or can be stretched to fulfil distributed wattage needs. Coil heaters can also accommodate integrated thermocouples for precise temperature control and quick response. The thermocouple can be of type ‘J’ and type ‘K’ and can be terminated anywhere within the coil section.

Advantages

• High heating profile in compact spaces
• High performance and economical
• Precise Temperature control
• Fast response time
• Integrated Thermocouple
• Available in a variety of coiling and exit styles

Construction

• Nickel Chromium Resistance wire for maximum life
• High Purity magnesium oxide fill selected for maximum dielectric strength and thermal conductivity, highly compacted for maximum heat transfer
• Stainless steel sheath / Inconel sheath for oxidation and corrosion resistance in a wide variety of environment
• Thermocouple for precise temperature control (type ‘J’ and type ‘K’ thermocouple)

Applications

• Zinc Die Casting Machine
• Packaging Machines- Sealing bar and jaws
• Plastics and die casting industries -Machine nozzles
• Hot runner system – Nozzles, Bushings & Distribution plates
• Tube Extrusion
• Pipe Forming
• Small Manifold heating
• Hot Metal forming dies and punches
• Semiconductor manufacturing and wafer processing

Do you seek professional assistance for customer training requirements? Do you have some products that need professional help for explaining their operations and upkeep? If the answer is yes than it is good to contact us. Ours is a professionally managed firm, involved in providing customer training services to the clients as per their schedule and budget. We have a team of qualified professionals well-versed with the technicalities of different products. For getting professional assistance or any kind of discussion; feel free to contact us.

Bundle Rod Heater consists of circular ceramic beads that hold the heating elements. They are designed for long life and maintenance-free operation. Designed & manufactured in low voltages for faster heating in order to achieve temperatures quickly, these heaters can be mounted horizontally or vertically. The element can be provided in ferritic alloys up to 1250° C and Ni Cr alloy up to 1100°C materials.

Construction

• Direct heating element wire
• Ceramic Disc : for hold the heating element & insulation
• Fiber Disc : for holds the terminal rod and prevent heat loss
• Center rod : for alignment & take weight of heater bundle

Advantages

• Carbon Dioxide emissions are reduced to avoid the corrosion of furnace gas to the heating element or avoid the contact of burning outcome.
• Convenient to control temperature, assemble and maintenance and easy to seal.
• Can be Horizontal or vertical mounted
• Better technical properties and longer working life
• Higher resistivity & surface load
• Free from oxide debris
• Cost-effective with High watt density output.

Application Areas

• For melting furnace and aluminum holding
• In steel industries, for galvanizing furnace
• In automotive industries, heat treatment furnace
• Annealing furnace
• Carburizing furnace

Fiber Bragg Grating (FBG) works as distributed Bragg reflector (DBR) build on an optical fiber with the help of periodic variation in the refractive index of the single-mode fiber core. When light is passed through the FBG it will reflect a certain wavelength of light and transmits all other. When temperature or strain around Grating changes, shift in reflected wavelength is observed.

Applications

• Hydro Power Plant Monitoring.
• Aerospace industries.
• Medical Industry.
• Petrol and Gas Exploration.
• Structural Health Monitoring.
• Tunnels and Pipelines Monitoring

Key Features:

• Multiplexing capability.
• Single and multipoint sensing.
• Immunity to electromagnetic and RF interference.
• Intrinsically safe operation.
• Small and lightweight.
• High sensitivity and long-term reliability.

Accessories:

• Software : BRAGGVIS
• Operation Manual

Optical fiber distributed temperature sensor enable to monitor of continuous temperature profile along the length of a fiber. Fiber itself is used as a sensing material. Distributed temperature sensing (DTS) can provide thousands of temperature measurements over a long distance, a few kilometers. Our DTS system works on the principle of Raman light scattering combined with OTDR (optical time domain reflectometry).

• Applications
• Linear temperature sensing along pipelines and tunnels.
• Fire prevention.
• Leakage detection in oil and gas pipelines.
• Conveyor belt monitoring.
• Power tranmission lines.
• Transformer winding temperature measurement.
• Reactor skin temperature monitoring.

Key Features :

• Intrinsically Safe.
• Fiber Sensor.
• Linear Monitoring.
• Chemically Stable.

Key Features :

• Software: DTSVIS
• Operation Manual

We have adopted several methods for making safe and hassle-free payments. The customers get both offline and online options to make payment to us. Our comprehensive range of products is packed in sturdy, safe, and industrial grade materials that safeguard the contents inside from harm, dampness, dust, movement etc. Besides, the packing has printed product information.

Slide shoe bearing RTDs :

• Vibration proof RTDs for Bearing & DG sets
• Motor & Transformer winding temperature RTDs
• Handheld & Probe in various designs
• RTDs with IBR approved Thermowells
• Strap on RTDs for nuclear application
• High Temperature RTDs upto 1/10 DIN
• Semi Standard PRTs. with NABL Certificate Calibrated on Fixed points suitable up to 661°C (Freezing Point of AI)

Electric Conveyor mesh belt type furnaces are used for continuous heating purpose of large quantities of goods. Conveyor belt continuously rotate through the furnace electrically which poses the temperature (250°C to 1200 ºC). Material to be heated is kept at one end on belt which passes through the furnace.

Key Features

• Continuous heating purpose of large quantities of goods. Material to be heated is kept on Conveyor belt which continuously rotate through the furnace.
• Maximum temperature (ambient to 1150°C). The furnace is designed to operate with hydrogen atmosphere, cracked ammonia atmosphere, nitrogen and argon atmosphere.
• Specially designed corrugated muffles (metallic) are used to withstand thermal expansion for certain processes. Metallic muffles may be of stainless steel or high nickel and chromium based alloys.
• Energy efficient, Improve productivity and excellent repeatable heat treatment.
• A variable speed drive unit with widely adjustable belt speeds allows the treatment of different thicknesses of materials and grades with varying temperature-time requirements.

Key Features :

• Precise monitoring operation detecting temperature trends in the transformer.
• Predict hazards.
• Effectively regulate loads.
• Prolong life expectancy of transformers.
• Optimize design level and manufacturing quality.
• Guarantee to safely transfer loads under
• Unpredicted condition.
• Cooling system automatically engage to ensure
• No damage occurs to the transformers insulating properties.

The assistance of our sophisticated packaging system and skilled personnel, we are able to meet the standard as well as customized packaging requirements of the clients with ease. Located at Udaipur(India), we are reckoned for providing excellent array of products throughout the country.

Features:

• Excellent electrical conductivity
• High grade PVC insulation
• Superb heat bearing capacity

SSPRT provides an affordable alternative for precision temperature measurement and calibration in labs & fields. Metal Sheathed Semi Standard Platinum Resistance Thermometer is widely used as a reference to calibrate various temperature probes, particularly in secondary calibration laboratories. SSPRT is constructed with a 6 mm outer diameter metal sheath of high durability. Inside the sheath, the sensing element is protected to shield the sensor from contamination by free-floating metal ions found within the metal environment at high temperatures. The electrical configuration is a four-wire current potential hookup to eliminate the effect of lead wire resistance. A special powder mixture is filled into the sensor capsule to support the element wire to protect the element from mechanical shocks. The element is housed in a special protective Assembly to ensure minimum drift over long term use.

High accuracy Platinum Resistance Thermometer (PRT) is an interpolating instrument converting temperature to resistance. It works together with readout device to measure temperature or change of temperature. It has wide applications for dry-wells or temperature baths.
It is recommended to calibrate this PRT annually over the full temperature range in between annual calibrations; user can check the drift rate by comparing RTPW against the last Calibration results.

Accuracy

• ±0.31°C at -80°C
• ±0.15°C at 0°C
• ±0.35°C at 100°C
• ±0.65°C at 250°C
• ±0.95°C at 400°C

Fuel Gas Heater Skids are sub-assembly of a complete fuel gas conditioning system or fuel gas filtration package skids. The heating systems are used to preheat the fuel gas to the desired temperature at a specified pressure and flow rate, prior to feeding to the actual process or further circulations.
The specially designed Fuel gas heating skids helps to monitor, regulate the gas flow with multiple safety features for the trouble-free and risk-free operation. The system is designed considering the incoming gas properties along environmental conditions to achieve the desired outlet flow conditions.
The skids are generally used for preheating the gas above its dew point, prior to feeding into the other equipment such as Gas operated turbines, generators or other process applications. The system can also be used for superheating the gas for other industrial applications.

ConstructionEach fuel gas heater skid is custom made design to suit respective process specifications. A typical Fuel gas heater skid system consists of:-

• Electric Heater Bundle
• Pressure Vessel or housing for the heater bundle
• Control panel for the heater operation control
• Temperature sensors such as RTDs, Thermocouples, Temperature transmitters
• Pressure safety valve
• Valves for flow control
• Power & Instrument Wiring
• Skid base for easy installation at site

With us, clients can stay assured for the premium quality of the offerings as we keep them in healthy conditions. For this, we have developed a large storage unit. Catering to the customers' needs with excellence, we are engaged in offering high quality lot of Heat Resistant Cables.

Features:

• Excellent electrical conductivity
• High grade PVC insulation
• Superb heat bearing capacity

The Tempsens Laboratory and Industrial ovens Series offered a range of precision electric ovens. They are designed for low temperature thermal treatment such as drying, heating and thermal testing in an air-flow assisted environment.
Our ovens are available with optional NABL calibration of the temperature controller and thermocouple as a system or also with a 3-point or 5-point thermal survey of the chamber volume.

Standard Features

• Capacity – 4 Liter to 14000 Liters
• Temperature uniformity throughout the chamber with forced air convection
• Temperature range up to 500ºC
• Digital PID temperature controller
• Safety controller for over-temperature protection
• Tubular Heaters/Nichrome are used as a heating element inside the oven for better uniformity

Industrial Bottom Loading Furnace is suitable for 1600°C as well as 1800°C application. The Industrial Bottom Loading Furnace is a kind of user friendly operating system that comes with smooth bottom lifting arrangement.
The Industrial Bottom Loading is widely used for firing and sintering of advanced ceramics and high temperature glass melting application. Industrial Bottom Loading Furnace offers high temperature accuracy in a range of ±1°C

All thanks to our smart inventory management owing to which safe and quick deliveries are furnished by us. As we promise to offer quality approved products to the clients, we make use of only high-grade raw materials selected from one of the best sources present in the market.

Features:

• Excellent electrical conductivity
• High grade PVC insulation
• Superb heat bearing capacity

Using only quality raw materials, our entire range of products is manufactured. We make sure that the raw materials we use are thoroughly checked against varied quality parameters. All thanks to our smart inventory management owing to which safe and quick deliveries are furnished by us.

Features:

• Excellent electrical conductivity
• High grade PVC insulation
• Superb heat bearing capacity

CALsys -80/50 is a Highly Stable Stirred Liquid Bath for Calibration RTD / Thermocouple and also for compensation of cold junction. CALsys -80/50 offers the temperature range of -80 to 50°C. It has large tank which is filled with liquid Methanol. The liquid is heated or cooled to the desired temperature. It has better stability & uniformity than dry block bath and as it uses of stirred liquid. This CALsys -80/50 is built using CFC free refrigerants.

Key Features:

• Large Immersion Depths
• High Accuracy
• High Stability and Uniformity
• Wide Temperature Range
• PC Interface
• Simple to use and Cost effective

Accessories:

• Reference Standard PRT.Part No. TPRT-A-300
• NABL accredited calibration certificate - 3 point.
• Software - Cal Soft including for setting bath temperature and monitoring the PV. Graphical representations of PV/TIME with 2 hours data logging.
• Operational Manual.

CALsys -80/50 Autocal is an automatic calibration system for  RTD / Thermocouple and also for compensation of cold junction. CALsys -80/50 offers a temperature range of -80 to 50°C. It has large tank which is filled with liquid Methanol. The liquid is heated or cooled to the desired temperature. It has better stability & uniformity than dry block bath and as it uses of stirred liquid.The system consist of a Temperature bath and PC Software, which together contribute to the whole cycle of the auto-calibration process.The system accepts 4 channels, 4 thermocouples or RTDs. The connection for these channels through special type off locking connectors. The channel configuration can be done with LCD display via touch screen keypad. The thermocouple microvolt & RTD ohm reading for each channel is monitored with CJC compensation. After the calibration PC software generates a report of actual calibrated values for the inputs.

Key Features:

• Large Immersion Depths
• High Accuracy
• High Stability and Uniformity
• Wide Temperature Range
• PC Interface
• Simple to use and Cost-effective
• Four channels(one master and three test sensors ), high-quality universal LEMO connector suitable both for T/C (J, K, N T, R, S, B type) and Rtd.
• Software for data recording Manual Mode and Test Certificate generation in Auto Mode

Accessories:

• Reference Standard PRT.Part No. TPRT-A-300
• NABL accredited calibration certificate - 3 point.
• Software - Cal Soft including for setting bath temperature and monitoring the PV. Graphical representations of PV/TIME with 2 hours data logging.
• Operational Manual.

Input: Four Channels (One master and three test sensors), high-quality LEMO connector suitable for both T/C and Rtd.

Software: The calibrator will be provided with software for data recording (Manual Mode) and report generation in Auto Mode.

CALsys -35/200 Autocal is a Highly Stable Stirred Liquid Bath for Calibration RTD / Thermocouple and also for compensation of cold junction.
CALsys -35/200 Autocal offers a temperature range of -35 to 200°C. It has a large tank that is filled with liquid (Water+Methanol/Silicon Oil). The liquid is heated or cooled to the desired temperature, where Methanol+Water are used for Negative Temperature and Silicon Oil is for Heating purpose.It has better stability & uniformity than dry block bath and as it uses of stirred liquid. This CALsys -35/200 is built using CFC-free refrigerants.
The CALsys -35/200 Autocal is an automatic temperature of the calibration system for thermocouples and RTDs. The system consists of Temperature bath PC software, which together contributes to the whole cycle of the auto-calibration process. The system accepts 4 channels, 4 thermocouples, 4 RTDs.The channel configuration can be done with an LCD display via a touch screen keypad. The thermocouple microvolt & RTD ohm reading for each channel is monitored with CJC compensation. After the calibration process is complete the PC software generates a report of actual calibrated values for inputs.

Key Features:

• High Accuracy
• High Stability and Uniformity
• Wide Temperature Range
• PC Interfacing
• Simple to Use and Cost-Effective

Accessories:

Standard Accessories

• Reference Standard PRT…Part No.TPRT-A-300
• NABL accredited calibration certificate - 3 point
• Software - Including for setting bath temperature and monitoring the PV. Graphical representations of PV/TIME.
• Operational Manual

Optional Accessories

• Methanol.10 Ltr. No.(3050-M)
• Silicon Oil.10L Part No.C200S-LB SO

Input (CaLsys -35/200 Autocal): Four Channels (One master and three test sensors), high-quality LEMO connector suitable for both T/C and Rtd.
Software (CaLsys -35/200 Autocal): The calibrator will be provided with software for data recording (Manual Mode) and report generation in Auto Mode.
Data Logging (CaLsys -35/200 Autocal): Data Logging facility with logged data export to the computer through  LAN port (Optional USB)

CALsys -40/50 is a Highly Stable Stirred Liquid Bath for Calibration RTD / Thermocouple and also for compensation of cold junction.
CALsys -40/50 offers the temperature range of -40 to 50°C. It has large tank which is filled with liquid Methanol. The liquid is heated or cooled to the desired temperature. It has better stability & uniformity than dry block bath and as it uses of stirred liquid.
This CALsys -40/50 is built using CFC-free refrigerants.

Key Features:

• Large Immersion Depths
• High Accuracy
• High Stability and Uniformity
• Wide Temperature Range
• PC Interface
• Simple to use and Cost-effective

Accessories:

• Reference Standard PRT.Part No. TPRT-A-300 NABL accredited calibration certificate - 3 point.
• Software - Cal Soft including for setting bath temperature and monitoring the PV. Graphical representations of PV/TIME with 2 hours data logging.
• Operational Manual.

CALsys -35/200 is a Highly Stable Stirred Liquid Bath for Calibration RTD / Thermocouple and also for compensation of cold junction.
CALsys -35/200 offers the temperature range of -35 to 200°C. It has large tank which is filled with liquid (Water+Methanol/Silicon Oil). The liquid is heated or cooled to the desired temperature, where Methanol+Water are used for Negative Temperature and Silicon Oil is for Heating purpose.
It has better stability & uniformity than dry block bath and as it uses of stirred liquid. This CALsys -35/200 is built using CFC-free refrigerants.

Key Features:

• High Accuracy
• High Stability and Uniformity
• Wide Temperature Range
• PC Interfacing
• Simple to Use and Cost-Effective

Accessories
Standard Accessories

• Reference Standard PRT…Part No.TPRT-A-300
• NABL accredited calibration certificate - 3 point
• Software - Including for setting bath temperature and monitoring the PV. Graphical representations of PV/TIME.
• Operational Manual

Optional Accessories

• Methanol.10 Ltr. No.(3050-M)
• Silicon Oil.10L Part No.C200S-LB SO

Input (CaLsys -35/200 Autocal): Four Channels (One master and three test sensors), high-quality LEMO connector suitable for both T/C and Rtd.

Software (CaLsys -35/200 Autocal): The calibrator will be provided with software for data recording (Manual Mode) and report generation in Auto Mode.

Data Logging (CaLsys -35/200 Autocal): Data Logging facility with logged data export to the computer through  LAN port (Optional USB)

The calibrator controller uses a precision RTD as a controlling sensor and controls the well temperature with thermoelectric cooler. To obtain and maintain a required temperature the controller varies the power to the heater via solid-state relay. There is one electricity driven fan which is situated under the heating chamber for cooling the heater. The dry block calibrator was designed for portability, moderate cost and ease of operation.
This dry block furnace is based on thermo electric cooling circuitry. This model provides an special design isothermal enclosure (Aluminium block) in which the thermocouple/RTD can be calibrated against the temperature of the calibrator.

Key Features:

• Wide Operating Range (-30 to110°C)
• High Stability
• PC Interfacing
• Simple to use and cost effective
• Portability
• Low temperature calibration facility upto -30°C
• Conveniently handle and calibration
• Light Weight

Accessories:

• NABL accredited calibration certificate - 3 point
• Software - cal soft including for setting bath temperature and monitoring the PV. graphical representations of PV/time with 2 hours data logging.
• Operational manual
• Carry case

High accuracy Platinum Resistance Thermometer (PRT) is an interpolating instrument converting temperature to resistance. It works together with readout device to measure temperature or change of temperature. It has wide applications for dry-wells or temperature baths.
It is recommended to calibrate this PRT annually over the full temperature range in between annual calibrations; user can check the drift rate by comparing RTPW against the last Calibration results.
High accuracy Platinum Resistance Thermometer (PRT) is an interpolating instrument converting temperature to resistance. It works together with readout device to measure temperature or change of temperature. It has wide applications for dry-wells or temperature baths.
It is recommended to calibrate this PRT annually over the full temperature range in between annual calibrations; user can check the drift rate by comparing RTPW against the last Calibration results.

Accuracy:

• 0.23C at -80C
• 0.10C at -0C
• 0.27C at 100C
• 0.43C at 200C
• 0.60C at 300C

High accuracy Platinum Resistance Thermometer (PRT) is an interpolating instrument converting temperature to resistance. It works together with readout device to measure temperature or change of temperature. It has wide applications for dry-wells or temperature baths.
It is recommended to calibrate this PRT annually over the full temperature range in between annual calibrations; user can check the drift rate by comparing RTPW against the last Calibration results.

Accuracy:

• 0.10C at - 38C
• 0.06C at 0C
• 0.16C at 100C
• 0.26C at 200C
• 0.31C at 250C

High accuracy Platinum Resistance Thermometer (PRT) is an interpolating instrument converting temperature to resistance. It works together with readout device to measure temperature or change of temperature. It has wide applications for dry-wells or temperature baths.
It is recommended to calibrate this PRT annually over the full temperature range in between annual calibrations; user can check the drift rate by comparing RTPW against the last Calibration results.

Accuracy:

• 0.04C at -38C
• 0.03C at -0C
• 0.08C at 100C
• 0.13C at 200C
• 0.155C at 250C

We can be contacted for customized packaging solutions. Besides the standard packs, we can sort items in desired quantity and pack them accordingly. Our packaging is premium. We understand that the use of finest grade raw material brings forth high quality product line. In addition to this, we make sure that the material is sourced from the reliable places only.

Details : High accurate Mineral Insulated Thermocouples for variety of application Type J, K, T, E, N Element size (MI) 3, 4.5, 6, 8, 10 (mm) Other Sizes on request Protection Sheath M SS321, SS316, SS310, INCONEL 600, 601, Platinum, Pyrosil, Nimonic, HRS 446 etc. Configuration Simplex / Duplex / Multipoints Special As per ASTM E235 for nuclear application

Buyers can stay rest assured with us for their orders as we ensure zero damage to the products that we deliver. For this, we store the entire lot in a spacious warehouse till the final dispatch. We have divided our infrastructure into different units including packaging unit wherein we pack our offerings meticulously to circumvent loss during transit.

Type : Pt 100, 200, 500, 1000 cu-50, 53 etc.

Connection :  2, 3, 4 wire

Element Dia :  1.5, 3, 4.5, 6, 8 mm

Configuration :  Simplex/Duplex/Others

Provide superior thermal environment for probe immersion as no air gap exist between the probe and the medium Thermal coupling is therefore much better than the alternatives described, and the stirring results in very even heat distribution throughout the medium. Methanol is used for temperature below 0°C, water from 0 to 80°C and silicon oil for upto 250°C. We have seven types of liquid baths given below.
CALsys 250 calibration bath is a highly stable standard stirred liquid bath for calibrating RTDs / Thermocouples and other temperature sensors in the laboratory. The temperature of the bath is set and controlled by a self-tuned PID controller with automatic super fine adjustment. The unique feature is portability with very high stability and uniformity.
The medium used in the bath is silicon oil.

Key Features:

• Large Immersion Depths
• Wide Operating Range (50 to 250°C)
• High Stability and Uniformity
• PC interfacing
• Simple to use and cost-effective
• Portability

Accessories:

• Silicon Oil. Part No.C300S-LB-SO
• NABL accredited calibration certificate - 3 point.
• Software - Cal Soft including for setting bath temperature and monitoring the PV. Graphical representations of PV/TIME with 2 hours data logging.
• Operational Manual.

Catering to the customers' needs with excellence, we are engaged in offering high quality lot of Lead Wires. Our storage facility is capacious to maintain large stock. So, clients are free to approach us for urgent and massive requirements.

Features:

• Excellent electrical conductivity
• High grade PVC insulation
• Superb heat bearing capacity

To maintain availability of products all year round and escape the issue of stock-out, we have established a state-of-the-art warehousing building and incorporated it with the latest inventory control system. High-quality and certified inputs are used for the production of our finished goods. We, as a trusted name, only select the certified vendors for procuring quality raw materials.

Type : Pt 100, 200, 500, 1000 etc.

Element size (MI) :  Wire wound ceramic encapsulated, Wire wound glass encapsulated Thin, film ceramic encapsulated

Connection : 2, 3, 4, wire

Accuracy :  Class A, B, ?, 1/3, 1/5, 1/10, DIN

Protection Sheath : SS304, SS321, SS316, SS310, Inconel 600/800, HRS 446, Hastalloy, Monel etc.

Configuration :  Simplex/Duplex/Others

The PH Hopper Heating Module is a rugged design, the high-performance heating surface of the hopper. The Marathon hopper heater are self-contained heaters whose designed provide heat outputs up to 3 watt/squire inch, with a maximum circuit size of 4500watts depending on the application, the design of the hopper heater is such that it distributes heat over its entire surface. The  PH module is according to customer requirements of surface heating area and application. The heater is offered in multiple designs, each one includes a heater element made of Inconel/Nichrome/SS. The heater element which provides multiple flow paths for electrical current to pass. This design eliminates the burnout chances common with series wire-based design.

Construction

• Parallel circuit high-temperature alloy heating element.
• Temperature-rated insulation- Mica and glass wool.
• Aluminum/Aluminized steel protective enclosure and its cover with mounting channel attachment.
• High temperature insulated lead wire for connection

Hopper Heating Modules for Power PlantsConveying coal/oil (other material) from stockpiles to boiler during winter months is a well-documented nightmare for plant operators. Identical conveying problems exist within the mining industry as coal is moved around the mine site.  Coal stored outdoors on the stockpile or delivered by unit train or barges picks up moisture from rain and snow. When this wet or frozen coal is conveyed, it inevitably comes into contact with the plate steel of the various hoppers and chutes within the coal handling system. During winter, this plate steel is below freezing for extended periods. When wet or frozen coal encounters steel at sub-freezing temperatures an instantaneous bond is formed. This bond causes immediate and often catastrophic blockage of the hopper and chutes. The bond and resultant blockage are so severe that often pneumatic drilling equipment and explosives are required to free up the system. This problem, known as  Flash Freezing, is extremely inconvenient and very costly. Several cases are documented where utility and industrial boilers have been shut down due to blocked conveying systems.

Features :

• Max. Temp. upto 260ºC
• Excellent Heat Resistant
• Outstanding Insulating Properties
• Good Thermal Stability
• Flame Retardant
• Passes JSS 51034 Flame Test

Available Options :

• Metal braiding 
• Fibreglass braided
• Polymide Insulated
• Special Color Code
• Calibration Test Repot

FastCAL 3000 is a high-temperature blackbody source with a capacity to produce high temperature using high emissivity emitter(graphite tube) and at the same time stabilize at the required temperature within a few minutes.
It is mainly used to calibrate non-contact temperature sensors. Step change in temperature is achievable within seconds. The graphite tube has an emitter diameter of 25mm (1.00") and emissivity of +0.995 ±0.005. Target temperature is sensed by a noncontact temperature sensor/Pyrometer which gives feedback to PID controller to regulate the cavity temperature precisely to the desired set points. Remote set point is achieved via RS-232 C communication port.
All safety features to protect equipment and operator are easily accessible.

Key Features:

• Water flow failure
• Increase in water temperature
• Argon gas flow failure
• Over current

We are backed by a reliable team of packaging professionals and modern facility that aid us completely for furnishing standard as well as tailored packaging requirements of the patrons. Owing to our sound quality system, we are capable of carrying out strict quality analysis of the product basket.

Features:

• Excellent electrical conductivity
• High grade PVC insulation
• Superb heat bearing capacity

With us, clients can stay assured for the premium quality of the offerings as we keep them in healthy conditions. For this, we have developed a large storage unit. Being a high-flying name in this arena, we promise to deliver the best in line quality products. In addition to this, we make sure that the offered lot is prepared using the finest grade material.

Features:

• Excellent electrical conductivity
• High grade PVC insulation
• Superb heat bearing capacity

Our team members and quality auditors keep regular checks on the quality of products and thus, even the raw material used is tested under vigil supervision to ensure better quality products. Our pool of experts makes certain that the products are as per the pre-defined quality standards and thus customers' can rely on us.

Features:

• Excellent electrical conductivity
• High grade PVC insulation
• Superb heat bearing capacity

Catering to the customers' needs with excellence, we are engaged in offering high quality lot of Mineral Insulated Thermocouple Cables. We have invested a large amount for developing storage unit that helps us in keeping a large stock for fulfilling urgent and massive requirements of the customers.

Features:

• Excellent electrical conductivity
• High grade PVC insulation
• Superb heat bearing capacity

Our team makes every effort to present a qualitative and certified array of products. Raw materials are the essential bottleneck assets that are highly important for the production of the finished goods. Thus, we stringently check the inputs before procurement.

Features:

• Excellent electrical conductivity
• High grade PVC insulation
• Superb heat bearing capacity

We have a team of quality examiners who strictly check the product quality so as to attain maximum client satisfaction. We make sure that our payment procedure is safe and simple. We offer our clients methods like online payment gateway, electronic funds transfer, cash, bank deposits and various others.

Features:

• Best quality
• QC tested
• Cost effective

Make payment securely with a payment option you are comfortable with. We accept payment through offline as well as online modes. We make sure proper documentation is done. Based in Udaipur(India), our organization is involved for years in supplying the finest grade of Protection Tubes in the industry.

Details : Type KER 710(C-799) Open Ended, Close Ended Lenth 350, 530, 600, 650, 740, 900, 1030, 1200, 1430 mm etc. OD x ID 6x4, 8x5, 10x6, 12x8, 15x10, 20x15, 24x18mm etc. Insulating Tubes 2/4/6 Holes etc. OD 1.5, 2.8, 3.5, 5.5, 8.5 etc.

We allow our patrons to make payment through a variety of methods. We are comfortable with patrons making payment through online or offline mediums that are legal and trusted. Ours is the known organization deeply ingrained in the Udaipur(India) and make sure to reach any destination with ease.

Owing to our reliable transportation amenities, we are capable to deliver the placed orders within the given timeframe and at the right place. We are supported by such storage facility that provides protection from diverse damaging factors such as dust, moisture, rain, sunlight, etc. Also, we maintain complete hygiene inside the unit.

Details : Material AISI SS316, SS304 , SS303, Carbon Steel, Brass Thread NPT, BS

All thanks to our smart inventory management owing to which safe and quick deliveries are furnished by us. We have an association with respected vendors from whom we source the raw inputs at very affordable charges. Additionally, the inputs are stringently checked before procurement.

Details : Material AISI SS304, SS316, SS316L, Carbon Steel, Cast Iron etc Size 1/2" to 4" & Others Rating 150# to 2500# etc.

Ours is a professionally managed firm, providing NABL accredited on-site calibration that includes on site calibration of temperature sensors. We are based in Udaipur (Rajasthan, India) and serving clients in the surrounding regions. Our associates visits the site as scheduled by the client and provide precise solutions using modern work methods & equipment. calibration is performed with minimal disruption and detailed documentation is provided upon completion. Our services are available for contact and non contact temperature sensors in temperature range -25^oC to 1200^oC & 0^oC to 1200^oC with the lowest down time. We charge reasonably for our services; clients can contact us anytime.

On-site calibration is required :

• When quick turnaround time is required.
• When instruments are very delicate and costly.
• Calibrations of large volume of instruments are to be done

Advantages of On-Site Calibration :

• Save the time and expense of removing and reinstalling instruments
• Eliminates packing & dispatch cost of instruments.
• Avoids the risk of damage of delicate and costly instruments while shipping
• Additional calibrtion requirement if any, arises at the time of visit can also be solved.

Ours is a professionally managed firm, involved in providing calibration services for non contact temperature sensors i.e. infrared pyrometer traceable to both national and international standards. With our base located in Udaipur (Rajasthan, India), we are catering to requirements of SMEs and blue-chip firms. Ours team of professionals visits the clients’ site and perform calibration to save time and money of customer. Our service charges are reasonable, feel free to contact us anytime for further discussion.