Pelton WheelFitted with 18 buckets, nozzle for water jet, casing with one side of perspex sheet. The turbine develops 1 HP Approx. output power.The Whole piping of pelton turbine is in G.I. (2) & valves are ball valves type made by brass material.witch and starter suitable for the above monoblock pump set, mounted on a panel board.

Petrol engine test rig consisting of a multicylinder 4- stroke 4 cylinder petrol engine, developing about 10 H.P. at 1500 R.P.M. engine.The unit is accompanied with the following accessories :- ignition switch, a radiator, a self starter, a battery ammeter, a throttle control. Special arrangements by switches for cutting off ignition of each cylinder for morse test, all mounted on a suitable panel board, a battery for starting the engine, clutch arrangement.

The unit consist of

• Engine:- Petrol engine test rig consisting of a multicylinder 4- stroke 4 cylinder petrol engine, developing about 10 H.P. at 1500 R.P.M. engine.
• Loading device:- Electrical Dynamometer: A suitable capacity Generator With water rheostat, load bank & load measurement arrangement.
• The unit is accompanied with the following accessories:- ignition switch, a radiator, a self starter, a battery ammeter, a throttle control. Special arrangements by switches for cutting off ignition of each cylinder for morse test, all mounted on a suitable panel board, a battery for starting the engine, clutch arrangement.
• Fuel arrangement:- Fuel tank mounted on a sturdy iron stand, burette tube, 3 -way cock connecting tube, a stop watch.
• Cooling water arrangement:- Cooling water arrangement by cooling piping. A Measuring Jar to determine the discharge of cooling water. Special arrangement to use either radiator or external cooling water supply system.
• Exhaust gas temperature- Digital temp. indicator
• Air intake measurement:- Air intake reservoir with orifice plate & Differential manometer.

SERVICE REQUIRED:1) 230 V. A.C. supply earthing connection.2) Rigid foundation to absorb the vibration.3) Water supply and piping to & from engine, calorimeter & dynamometer to be provided by Institute.4) Petrol / Diesel for Testing.

The unit consist of a 4 4-stroke diesel engine coupled to an Electrical Dynamometer. A water cooled brake drum along with spring balances is provided. For Electrical Dynamometer water rheostat is used as loading arrangement.

• SPECIFICATION:1) Diesel engine of 5 H. P. capacity, 1500 R. P. M. 4-stroke vertical, single cylinder engine.2) Electric Dynamometer: - A D.C. generator, with loading arrangement upto 2 Kw. Four air heater of 500 Kw.3) For Rope Brake Dynamometer Pully with spring balance
• Fuel measuring arrangement :- Consisting of a fuel tank, mounted on a strong iron stand, measurement of a fuel consumption by a burette & 3 way cock. Connecting tube, a stop watch.
• Cooling water arrangement:- Cooling pipes, thermocouples, measuring flask to determine the discharge of cooling water & heat carried away by cooling water.
• Exhaust gas temperature - digital temp. indicator
• Air intake measurement: - Air tank reservoir of size 0.4 m. x 0.4 m.x 0.4 m. with orifice plate, differential manometer, connecting hose.

RANGE OF EXPERIMENT:-To determine the1) B. H. P. & I. H. P.2) Mechanical and Thermal efficiencies.3) Air fuel ratio.4) Specific fuel consumption.5) Heat balance sheet.At various load conditions.

SERVICE REQUIRED:-1) Rigid foundation to absorb the vibration.2) Water supply and piping to & from Test Rig3) 230 V, A. C. supply with earthing connection.4) Petrol / Diesel for Testing.

Gear pumps are positive displacement rotary pumps. The unit is a self contained recirculation type unit. All the measurements are provided to evaluate the performance of the gear pump.

SPECIFICATIONS

• Gear pump with 1/2 H.P. 3-ph motor with three speed cone pulley mounted over the sump tank. Speed1500rpm.
• Sump Tank of size 900 X 400 x 400 mm with FRP lining
• Discharge measurement tank of size 400 x 300 x 400 mm with FRP lining
• Pressure gauge for discharge head.
• Energymeter for power input.
• Pressure rellet valve in discharge pipe.
• Needle valve to control discharge pressure.

RANGE OF EXPERIMENTS

Following characteristics can be determined
• Speed Vs Discharge
• Head Vs Discharge.
• Discharge Vs Input power.
• Discharge Vs Efficiency.

The unit consists of a centrifugal pump provided with variable speed motor. The pump is provided with a vaccum gauge at suction and a pressure gauge on discharge pipe. The pump is provided with a variable speed drive & gate valve at discharge which facilitates estimation of pump performance at various speeds & discharge heads. Power input to motor is measure with energy meter.

SPECIFICATION

• Centrifugal pump1"x1" size,
• Motor Variable Speed P.M.D. C. motor
• Speed Controller for Motor.
• Sump tank: 900X400X400MM
• Measuring Tank: 400X400X400MM.
• Energymeter for motor input measurement.
• Pressure & vaccum gauge for measurement of head.
• Stop watch.
• The assembly of pump & control are mounted on the sump tank.

RANGE OF EXPERIMENTSFollowing characteristics can be studied at different speeds

• Discharge vs. Head
• Discharge vs. Input to pump
• Discharge vs. pump efficiency.

SERVICES REQUIRED

• Floor space of 1 m. x 1 m.
• 230 V., 15 A, A. C. supply with earthing connection.

Output power

• Francis turbine 75 m.m. size to develop 1 HP at 1250 RPM, with a flow of about 1000 LPM at about 10 M head with Pressure Gauge and Vaccume Gauge.

Rope brake arrangement

• Belt Thickness 6 mm
• Drum diameter 190 mm

Pipes and Valves

• The Whole piping of Francis turbine is in M.S.

Pump Set unit

• 5 HP Supply pump set 75m.m. size, 1000 LPM at 14 m head sutiable for supplying water to the above turbine and for operation on 440 V, 3 phase, 50 cycle A.C.mains.

Electrical Units:L

• Switch and starter suitable for the above monoblock pump set, mounted on a panel board.

Flow Measuring Unit

Flow measuring unit consisting of a suitable venturimeter & Pressure Gauge
• Inlet of Venturimeter
• Throat dia. - 53
• Manometer - Double column differential Type.

Water storage unit

• Fiber Glass Lined M.S. sump to store sufficient water for independent circulation through the unit for experimentation & arranged within the floor space of the main unit.

SERVICES REQUIRED

• Suitable floor space of 2 m. x 1 m.
• 3 Phase Electrical Supply

Pelton WheelFitted with 18 buckets, nozzle for water jet, casing with one side of perspex sheet. The turbine develops 1 HP Approx. output power.The Whole piping of pelton turbine is in G.I. (2) & valves are ball valves type made by brass material.witch and starter suitable for the above monoblock pump set, mounted on a panel board.

Petrol engine test rig consisting of a multicylinder 4- stroke 4 cylinder petrol engine, developing about 10 H.P. at 1500 R.P.M. engine.The unit is accompanied with the following accessories :- ignition switch, a radiator, a self starter, a battery ammeter, a throttle control. Special arrangements by switches for cutting off ignition of each cylinder for morse test, all mounted on a suitable panel board, a battery for starting the engine, clutch arrangement.

The unit consist of

• Engine:- Petrol engine test rig consisting of a multicylinder 4- stroke 4 cylinder petrol engine, developing about 10 H.P. at 1500 R.P.M. engine.
• Loading device:- Electrical Dynamometer: A suitable capacity Generator With water rheostat, load bank & load measurement arrangement.
• The unit is accompanied with the following accessories:- ignition switch, a radiator, a self starter, a battery ammeter, a throttle control. Special arrangements by switches for cutting off ignition of each cylinder for morse test, all mounted on a suitable panel board, a battery for starting the engine, clutch arrangement.
• Fuel arrangement:- Fuel tank mounted on a sturdy iron stand, burette tube, 3 -way cock connecting tube, a stop watch.
• Cooling water arrangement:- Cooling water arrangement by cooling piping. A Measuring Jar to determine the discharge of cooling water. Special arrangement to use either radiator or external cooling water supply system.
• Exhaust gas temperature- Digital temp. indicator
• Air intake measurement:- Air intake reservoir with orifice plate & Differential manometer.

SERVICE REQUIRED:1) 230 V. A.C. supply earthing connection.2) Rigid foundation to absorb the vibration.3) Water supply and piping to & from engine, calorimeter & dynamometer to be provided by Institute.4) Petrol / Diesel for Testing.

The unit consist of a 4 4-stroke diesel engine coupled to an Electrical Dynamometer. A water cooled brake drum along with spring balances is provided. For Electrical Dynamometer water rheostat is used as loading arrangement.

• SPECIFICATION:1) Diesel engine of 5 H. P. capacity, 1500 R. P. M. 4-stroke vertical, single cylinder engine.2) Electric Dynamometer: - A D.C. generator, with loading arrangement upto 2 Kw. Four air heater of 500 Kw.3) For Rope Brake Dynamometer Pully with spring balance
• Fuel measuring arrangement :- Consisting of a fuel tank, mounted on a strong iron stand, measurement of a fuel consumption by a burette & 3 way cock. Connecting tube, a stop watch.
• Cooling water arrangement:- Cooling pipes, thermocouples, measuring flask to determine the discharge of cooling water & heat carried away by cooling water.
• Exhaust gas temperature - digital temp. indicator
• Air intake measurement: - Air tank reservoir of size 0.4 m. x 0.4 m.x 0.4 m. with orifice plate, differential manometer, connecting hose.

RANGE OF EXPERIMENT:-To determine the1) B. H. P. & I. H. P.2) Mechanical and Thermal efficiencies.3) Air fuel ratio.4) Specific fuel consumption.5) Heat balance sheet.At various load conditions.

SERVICE REQUIRED:-1) Rigid foundation to absorb the vibration.2) Water supply and piping to & from Test Rig3) 230 V, A. C. supply with earthing connection.4) Petrol / Diesel for Testing.

Gear pumps are positive displacement rotary pumps. The unit is a self contained recirculation type unit. All the measurements are provided to evaluate the performance of the gear pump.

SPECIFICATIONS

• Gear pump with 1/2 H.P. 3-ph motor with three speed cone pulley mounted over the sump tank. Speed1500rpm.
• Sump Tank of size 900 X 400 x 400 mm with FRP lining
• Discharge measurement tank of size 400 x 300 x 400 mm with FRP lining
• Pressure gauge for discharge head.
• Energymeter for power input.
• Pressure rellet valve in discharge pipe.
• Needle valve to control discharge pressure.

RANGE OF EXPERIMENTS

Following characteristics can be determined
• Speed Vs Discharge
• Head Vs Discharge.
• Discharge Vs Input power.
• Discharge Vs Efficiency.

The unit consists of a centrifugal pump provided with variable speed motor. The pump is provided with a vaccum gauge at suction and a pressure gauge on discharge pipe. The pump is provided with a variable speed drive & gate valve at discharge which facilitates estimation of pump performance at various speeds & discharge heads. Power input to motor is measure with energy meter.

SPECIFICATION

• Centrifugal pump1"x1" size,
• Motor Variable Speed P.M.D. C. motor
• Speed Controller for Motor.
• Sump tank: 900X400X400MM
• Measuring Tank: 400X400X400MM.
• Energymeter for motor input measurement.
• Pressure & vaccum gauge for measurement of head.
• Stop watch.
• The assembly of pump & control are mounted on the sump tank.

RANGE OF EXPERIMENTSFollowing characteristics can be studied at different speeds

• Discharge vs. Head
• Discharge vs. Input to pump
• Discharge vs. pump efficiency.

SERVICES REQUIRED

• Floor space of 1 m. x 1 m.
• 230 V., 15 A, A. C. supply with earthing connection.

Output power

• Francis turbine 75 m.m. size to develop 1 HP at 1250 RPM, with a flow of about 1000 LPM at about 10 M head with Pressure Gauge and Vaccume Gauge.

Rope brake arrangement

• Belt Thickness 6 mm
• Drum diameter 190 mm

Pipes and Valves

• The Whole piping of Francis turbine is in M.S.

Pump Set unit

• 5 HP Supply pump set 75m.m. size, 1000 LPM at 14 m head sutiable for supplying water to the above turbine and for operation on 440 V, 3 phase, 50 cycle A.C.mains.

Electrical Units:L

• Switch and starter suitable for the above monoblock pump set, mounted on a panel board.

Flow Measuring Unit

Flow measuring unit consisting of a suitable venturimeter & Pressure Gauge
• Inlet of Venturimeter
• Throat dia. - 53
• Manometer - Double column differential Type.

Water storage unit

• Fiber Glass Lined M.S. sump to store sufficient water for independent circulation through the unit for experimentation & arranged within the floor space of the main unit.

SERVICES REQUIRED

• Suitable floor space of 2 m. x 1 m.
• 3 Phase Electrical Supply