We are offering stator rotor controller. Interlocking between stator and rotor as per iss: 8544. Offers improvements in reliability as compared to l.r.s. Low maintence; incorporates switching through contactors. Smooth acceleration of the slip-ring induction motor. Reduces electrical and mechanical stresses of the machines. Can be custom designed as per customer’s requirements. The capacity of rotor controller is 15hp to 1000hp. We have applied closed circuit technology in all our stator-rotor controllers for the safe and smooth operation of slip-ring induction motors. Our controllers are built as per iecnema standards meeting the provisions of the national electric safety code. Stator rotor controllers rotor controllers are extensively being used to replace existing manually operated wound rotor starters and liquid rotor starters. The resistances are basically to provide high initial starting torque with low inrush current from mains in applications like high inertiahigh frictional loads and during run-up are bypassed through contractors by timers to shot out final rotor contactor until full speed is attained. The rotor controller provides acceleration to full speed and thus reduces electrical and mechanical stresses in the motor and drive. The resistances incorporated in our rotor controllers are designed in such a manner that they provide a very long term service with zero maintenance. All our rotor controllers are designed to start wide range of motors with strict qa system.

We are offering auto transformer starters controller panel. Motor is connected in delta from the start. Auto transformer provides voltage to the motor at start. Appropriate lower voltage tapping- customized as per the application- is provided to the motor. After the motor has attained significant torque changeover from auto transformer to on line takes place. The changeover is “closed transition” i.e. During changeover the auto transformer acts a choke supplying voltage to motor- hence smooth or stepless or soft starting takes palace. The motor then runs on line current. The transformer is isolated from both the ends to protect the contactors. Adjustable high torque: a high torque (up to 64%) possible and can be customized by voltage taping. No power quality issues: all standards electrical components ensure that there are no harmonics or other power quality issues. Transient elimination: korndorfer closed transition technology ensures that transients are eliminated. Motor protection: motor is connected in delta at the time of starting to avoid high inrush current in the motor winding thus providing lesser heat generation. Reduced voltage starter: voltage controlled by auto transformer at the time of starting. The capacity of ats is 15hp to 1000hp.

We are offering automatic power factor control panels. Syemco manufactures high end power saving products. The brand name of syemco had started the product “automatic power factr control panels” about a decade ago & are now pioneer in achieving power factor to unity. In view of constantly rising power tariff and penalties imposed by the state electricity boards / utility companies, it is imperative for any ht and lt industry of consumer to install a power factor control panel for curtailment of power factor penalty, reducing maximum demand and also save energy and power. Technical features: microprocessor based automatic controller with power display. All major components are of standard makes like, simens, l&t, epcos, neptune etc. All the components are carefully integrated for reliable performance and longer life. Used small correction steps to maintain accurate setting. Contactors (with mcbs or mccbs backup protection) are used to switch on capacitors with spiral conductor design to minimize switching surges. Auto / manual facility. In-built time delay for switching on of a capacitor bank to avoid impulse signal operation. Very low watt losses, capacitors are used. Product range: 20kvar to 1000kvar. Applications: all types of manufacturing units like solvent plants oil mills, ginning & pressing factories, chemical industries, food industries, rice mills, paper mills, fertilizer plants daal mills, steel industries, cement mills, spinning mills etc.

We are offering munnalal motor protector. Provision of tripping automatically the starter in case of overload due to which it gives relief from the worry of burning the motor. If there is phase short circuit or eating in starter outgoing, then mcb of starter will trip automatically due to which fault doesn’t multiply. Due to presence of rubber gasket starter is completely protected from dust, mud, water. Incoming & outgoing terminals are provided separately. Less electricity consumption due to main solid copper wiring. Entry of incoming wires is from the bottom of starter box to that there is no possibility of entering rain water. Two separate 6 mm bolts (with washer) are provided for earthing. The front door of starter is welded from hinge due to which no panic of falling of door. Rust free due t fully powder coating heavy panel box. No possibility of provocation & accident because unable to open starter without tool kit. The capacity of mlmp is 1 hp to 10 hp.

We are offering munnalal pump protector. Provision of starting starter automatically when all the 3phases are available, due to which maximum voltage is always available & will freedom from starting & stopping again-n-again. Due to presence of rubber gasket is completely protected from dust , mud & water. Incoming & outgoing (3phase, multi lock type) terminals are provided separately. Less electricity consumption due to main solid copper wiring (with glass coating & without lungs), entry of incoming & outgoing wires is from the bottom of starter box due to that there is no possibility of entering rain water. Two separate 6 mm bolts (with washer) are provided for earthing. The front door of starter is welded from hinge due to which no panic of falling of door. Rust free due to fully powder coating heavy panel box. No. Possibility of provocation & accident because unable to open starter without tool kit. the capacity of mlpp 1 hp to 10 hp.

We are offering power transformer, distribution transformer. Product ranges from 16 kva to 2000 kva up to 33 kv. Syemco transformer are designed and tested as per is: 2026, bs -171, iec -76 & iec- 126. Transformer will be connected as per vector group reference dyn 11. Other vector groups can be offered as per specific requirements. H.v bare bushing or cable box, l.v. bare bushing or cable box disconnecting. Transformers are designed for a maximum temperature rise of 40500 c of oil winding. Lower temperature rise can be offered on request. The core is constructed from low loss, cold rolled, grain oriented, annealed laminations of electrical sheet conforming to the latest international standards. Special frame is built in-house from clamping the core to reduce the magnetic noise as well as making the whole structure rigid and robust. Coils are wound with electrolytic high conductivity paper covered of synthetic enameled copper conductors. Cooling ducts are provided to keep the hot spot temperature as low as possible. Coils are dried in electric ovens. Rigid connection support and coil clamping is provided to ensure high short circuit strength. Precompressed board parmali board and japneese insulation paper of best quality is used. oil is tested for resistivity , dielectric and acidic character conforming to is-335. Before topping up oil is filtered thoroughly. The tanks are made of m.s. Steel platessheets with adequate bracing & stiffness. Tanks are pressure tested to withstand any type of inside or outside pressure, all the external surface are given a primary coat of zinc chromate, red oxide and two finishing coats of grey paint. The inner surfaces are given a coat of heat and oil resisting paint. All syemco transformers undergo rigorous quality control check and are routine tested as per is in our fully equipped laboratory. Any specific test required by the customer can also be arranged. standard fittings :- rating and diagram plate, earthing terminals-no.2, lifting lungs, oil level indicator. Drain –cum bottom filter valve with plug, oil filling hole with plug on conservator, oil conservator with drain plug, air release plug, silica gel air breather, bi- directional flate rollers, hv terminals-outdoor bushings, lv terminals –outdoor bushings, radiators, filter valve with plug, the mometer pocket, oil temperature indicator, externally operated off circuit tap changing switch, explosion vent.