Our Products
Switchgear & Panel Board
2 Products availableWe are leaders in the market for providing best range of Panel Heater (Connector End Right Fixing Perforated Cover), Panel Heater (Middle Left Fixing Perforated Cover), Panel Heater (End Fixing Without Cover), Panel Heater (Connector End Right Fixing Without Cover) and Panel Heater (Middle Left Fixing Without Cover)
Working Principle & Features : Body is made of anodized heatsink grade extruded aluminium for Fast dissipation of heat into air. High quality resistance heating element is insulated with mica for optimum insulation even in extreme humid conditions. Resistance element and insulation are held tight in between aluminium parts and squeezed for quick and uniform heating. Heater can withstand much higher degree of mechanical shock and vibration. Elevated body provides for easy passage of heat directly to air, ithout heating panel body and with perforated sheet metal enclosure. A black powder coated finish ensures rapid heat. Intended Use :Prevention of condensation, corrosion, Leakagecurrents in LT. & H.T. Switchgear panel boards / electronic instruments & panels etc.Installation : Four Holes of 6.3mm are provided for mounting on one side of the heater. Installation can be done in vertical or horizontal position although horizontal mounting is preferred. Distance from surface of panel should be at least 10mm. and distance from plastic parts should be at least 50mm. Remark :It is recommended to use a thermostat to control the heater.
Working Principle & Features :
Intended Use :Prevention of condensation, corrosion, Leakagecurrents in LT. & H.T. Switchgear panel boards / electronic instruments & panels etc.
Installation :
Remark :It is recommended to use a thermostat to control the heater.
Working Principle & Features : Body is made of anodized heat sink grade extruded aluminium for Fast dissipation of heat into air. High quality resistance heating element is insulated with mica for optimum insulation even in extreme humid conditions. Resistance element and insulation are held tight in between aluminium parts and squeezed for quick and uniform heating. Heater can withstand much higher degree of mechanical shock and vibration. Elevated body provides for easy passage of heat directly to air, ithout heating panel body. Intended Use :Prevention of condensation, corrosion, Leakagecurrent in L.T. & H.T Switchgear panel boards, enclosures, switch boards, & electronic instruments etc.Installation : Two fixing oval holes of 6.3 mmX8.4 mm are provided at each end. Installation can be done in vertical or horizontal position although horizontal mounting is preferred. Distance from surface of panel should be at least 10mm. and distance from plastic parts should be atleast 50mm. Remark : It is recommended to use a thermostat to control the heater.
Working Principle & Features : Body is made of anodized heatsink grade extruded aluminium for Fast dissipation of heat into air. High quality resistance heating element is insulated with mica for optimum insulation even in extreme humid conditions. Resistance element and insulation are held tight in between aluminium parts and squeezed for quick and uniform heating. Heater can withstand much higher degree of mechanical shock and vibration. Elevated body provides for easy passage of heat directly to air, ithout heating panel body and with perforated sheet metal enclosure. A black powder coated finish ensures rapid heat. Intended Use :Prevention of condensation, corrosion, Leakagecurrents in LT. & H.T. Switchgear panel boards / electronic instruments & panels etc.Installation : Four Holes of 6.3mm are provided for mounting on one side of the heater. Installation can be done in vertical or horizontal position although horizontal mounting is preferred. Distance from surface of panel should be at least 10mm. and distance from plastic parts should be at least 50mm. Remark :It is recommended to use a thermostat to control the heater.
Working Principle & Features : Body is made of anodized heatsink grade extruded aluminium for Fast dissipation of heat into air. High quality resistance heating element is insulated with mica for optimum insulation even in extreme humid conditions. Resistance element and insulation are held tight in between aluminium parts and squeezed for quick and uniform heating. Heater can withstand much higher degree of mechanical shock and vibration. Elevated body provides for easy passage of heat directly to air, ithout heating panel body and with perforated sheet metal enclosure. A black powder coated finish ensures rapid heat. Intended Use :Prevention of condensation, corrosion, Leakagecurrents in LT. & H.T. Switchgear panel boards / electronic instruments & panels etc.Installation : Four Holes of 6.3mm are provided for mounting on one side of the heater. Installation can be done in vertical or horizontal position although horizontal mounting is preferred. Distance from surface of panel should be at least 10mm. and distance from plastic parts should be at least 50mm. Remark :It is recommended to use a thermostat to control the heater.
We are reputed sellers engaged in providing best quality products to our buyers at reasonable prices.
Working Principle & Features : Body is made of anodized heatsink grade extruded aluminium for Fast dissipation of heat into air. High quality resistance heating element is insulated with mica for optimum insulation even in extreme humid conditions. Resistance element and insulation are held tight in between aluminium parts and squeezed for quick and uniform heating. Heater can withstand much higher degree of mechanical shock and vibration. Elevated body provides for easy passage of heat directly to air, ithout heating panel body and with perforated sheet metal enclosure. A black powder coated finish ensures rapid heat. Intended Use :Prevention of condensation, corrosion, Leakagecurrents in LT. & H.T. Switchgear panel boards / electronic instruments & panels etc.Installation : Four Holes of 6.3mm are provided for mounting on one side of the heater. Installation can be done in vertical or horizontal position although horizontal mounting is preferred. Distance from surface of panel should be at least 10mm. and distance from plastic parts should be at least 50mm. Remark :It is recommended to use a thermostat to control the heater.