Product / Services
Post Buy Requirement

My ExportersIndia

For Buyer

For Seller

For Help

SE

SVS Embedded
location Boduppal, Hyderabad, Telangana

Write a Review
Call Now Call Now

Our Products

  1. Electric Circuit Components & Parts 5 Products available
  2. Sensors 3 Products available

  3. Integrated Circuit

    1 Products available

  4. Audio Recorders, Mixers & Transmitters

    1 Products available

  5. Ladies Leggings

    1 Products available

  6. Telecommunication Equipment & System

    1 Products available

  7. Ethernet Device

    1 Products available

  8. Podium

    1 Products available

  9. LED Bulb

    1 Products available

  10. Thyristor

    1 Products available
  11. Others Products 16 Products available

Electric Circuit Components & Parts

Our Complete range of products are AVR ISP USB Programmer, RF-ID MODULE, HC-06 Bluetooth Transceiver, RESISTIVE TOUCHSCREEN + 128x64 GRAPHIC LCD DISPLAY and Graphic LCD Module 128x64.

AVR ISP USB Programmer

AVR ISP USB Programmer
The AVRISP is a professional low cost In-System Programmer covering all AVR 8-bit RISC Micro Controllers. The programmer connects to a PC through a standard USB and draws the necessary power from the PC USB port eliminating the need for an additional power supply. It can also power your target board up to 100ma from USB.AVR Studio is used as front-end software, giving you a highly integrated development solution. The AVR ISP is fully supported by AVR Studio, WINAVR, AVRISP. Programmer also supports AT89S51 and AT89S52 ICs along with all other AVR ICs Features AVR Studio InterfaceISP Programming of all AVR DevicesPrograms both Flash and EEPROMSupports Fuses and Lock Bit ProgrammingSupports RC Oscillator CalibrationUpgradeable to Support Future Devices by upgrading AVR studio softwareOperates at Target Voltages from 2.7V to 5.5VAdjustable Speed. Supports all Target Boards Running at Speeds Higher than 8kHzUSB Interface to PC for Programming and ControlTakes Power from USB. No need for Additional Power SupplyCan power target boards upto 100ma

Additional Information:

Packaging Details : Tested & Ready to use AVR-ISP USB Programmer covering 1 year warranty
CDROM containing AVR Studio programming software, USB Driver & PDF manual.
USB Cable for connecting to PC
10 pin Flat Cable connector for connecting to target boards

View Complete Details
Ask Latest Price & Details
RF-ID MODULE

RF-ID MODULE
This is a low frequency (125 KHz) RFID Reader with Serial Output with at range of 8-12cm. It is a compact unit with built in antenna and can be directly connected to the PC using RS232 protocol. This product is a kind of play and plug device with a reading range of 8 to 10 cm and can be availed in the following specifications.RFID READER SPECIFICATIONS : Power Requirement:7.5 - 9 Volts @ 500mA(adapter)Voltage: 5 vdcCurrent:
Ask Latest Price & Details
HC-06 Bluetooth Transceiver

HC-06 Bluetooth Transceiver
This is a bluetooth module for use with any microcontroller. it uses the uart protocol to make it easy to send and receive data wirelessly. the hc-06 module is a slave only device. this means that it can connect to most phones and computers with bluetooth but it cannot connect to other slave only devices such as keyboards and other hc-06 modules. to connect with other slave devices a master module would be necessary such as the hc-05 version which can do both master and slave.Features:a breakout board for easier connectivitydesigned for 3.3v level ttl but will accept 5v level as wellbuilt in antenna with a range of up to 30 feet (range is dependent on a lot of things such as any obstacles or walls in the way so it may vary)supports baud rates from 1200 to 1382400 bps (default is 9600 bps)vcc input voltage 3.3v to 6vbluetooth specification v2.0+edr
Ask Latest Price & Details
Heart Beat Sensor

Heart Beat Sensor
Introduction:if you intend to use the touch panel you should first consider these 2 items: 128x64 glcd with soldered connectortouchpanel overlay for 128x64 glcdvery high quality 128x64 yellow-black graphical lcd display with factory-mounted4-wire touchscreen.only 5v is required to power this jhd128x64 compatible lcd. Negative voltage supply (vee) for the lcd screen drive and contrast is built into lcd module. You can create your own touch panel control code using any compiler and microcontroller that has at least 4 adc inputs, as shown in the photos above. Compatible 4 x 1mm pitch fpc connectors are inexpensive and available from all the major electronic supply houses.
Ask Latest Price & Details
Tell Us What are you looking for? Will call you back

Contact Us

View Contact No.