Spray Drying is a unit process which converts solution, suspension or paste into dried particulate form by spraying the fluid in hot drying medium. Spray drying may proceed concurrently, counter currently, or as a mixed-flow process. Spray Drying can be achieved in stages depending upon the product quality. The Feed is atomized using a rotating wheel or a nozzle, and the spray of droplets immediately comes into contact with a flow of hot drying medium, usually air. Selection of the Atomiser is soledy dependent on the required final product quality and particle size. SVAAR offers single, two and three stage Dryer. Three stage dryers are often used when the final product agglomeration is required. Spray drying is used to dry pharmaceutical fine chemicals, foods, dairy products, blood plasma, numerous organic and inorganic chemicals, rubber latex, ceramic powders, detergents, and other products.

A Vertical Thin Film Dryer is a continuous Agitated contact dryer that can convert a suspension or a solution into a dry powder. This equipment originated from the Agitated thin fiIm evaporator that was used to concentrate solutions. The design is sturdy and can process pastes and powders. Viscous paste or liquid slurry can be processed in Agitated thin film evaporator. SVAAR offers Agitated thin film evaporator for various applications like Continuous Khoa plant, Chocolate Concentration, Sucrose Concentration, Spent wash Evaporation, Zero discharge plants.

Flash drying systems is in which particulate solids are dried during transport in a hot gas stream usually air or combustion gases. The simple flash drying system includes six basic components: the gas heater, the wet material feeder, the drying duct, the separator, exhaust fan, and a dried product collector. The wet particles are fed into the hot gas stream sometimes with special mixing devices. The stream flows up the drying tube. The gas velocity must be greater than the free fall velocity of the largest particle to be dried. The gas velocity in relation to the particle velocity is high. Thermal contact between the conveying air and the solids as mentioned above is usually very short and therefore flash dryers are most suitable for removal of external moisture (surface moisture) and are less suitable for removal of internal moisture. At the end of the drying process a dust separation arrangement is installed. It must comply with the regulations for pollution control. For this purpose cyclone dust separators, fabric filters, electrostatic precipitators, wet scrubbers, and fabric filters are used. Flash dryers are used in various Sectors of the chemical, pharmaceutical, ceramic, gypsum, wood, and mining industries. Flash dryers are simple in construction and have low capital cost and they are almost trouble free.

• CapacityUpto 60 TPD
• MaterialStainless Steel
• Usage/ApplicationSpray drying is used to dry pharmaceutical fine chemicals, foods, dairy products, blood plasma.
• TypeRotary and Nozzle Type
• Automation GradeAutomatic
• DesignCustomized

Spray Drying is a unit process which converts solution, suspension or paste into dried particulate form by spraying the fluid in hot drying medium. Spray drying may proceed concurrently, counter currently, or as a mixed-flow process. Spray Drying can be achieved in stages depending upon the product quality. The Feed is atomized using a rotating wheel or a nozzle, and the spray of droplets immediately comes into contact with a flow of hot drying medium, usually air. Selection of the Atomiser is soledy dependent on the required final product quality and particle size. SVAAR offers single, two and three stage Dryer. Three stage dryers are often used when the final product agglomeration is required. Spray drying is used to dry pharmaceutical fine chemicals, foods, dairy products, blood plasma, numerous organic and inorganic chemicals, rubber latex, ceramic powders, detergents, and other products.

A Vertical Thin Film Dryer is a continuous Agitated contact dryer that can convert a suspension or a solution into a dry powder. This equipment originated from the Agitated thin fiIm evaporator that was used to concentrate solutions. The design is sturdy and can process pastes and powders. Viscous paste or liquid slurry can be processed in Agitated thin film evaporator. SVAAR offers Agitated thin film evaporator for various applications like Continuous Khoa plant, Chocolate Concentration, Sucrose Concentration, Spent wash Evaporation, Zero discharge plants.

Flash drying systems is in which particulate solids are dried during transport in a hot gas stream usually air or combustion gases. The simple flash drying system includes six basic components: the gas heater, the wet material feeder, the drying duct, the separator, exhaust fan, and a dried product collector. The wet particles are fed into the hot gas stream sometimes with special mixing devices. The stream flows up the drying tube. The gas velocity must be greater than the free fall velocity of the largest particle to be dried. The gas velocity in relation to the particle velocity is high. Thermal contact between the conveying air and the solids as mentioned above is usually very short and therefore flash dryers are most suitable for removal of external moisture (surface moisture) and are less suitable for removal of internal moisture. At the end of the drying process a dust separation arrangement is installed. It must comply with the regulations for pollution control. For this purpose cyclone dust separators, fabric filters, electrostatic precipitators, wet scrubbers, and fabric filters are used. Flash dryers are used in various Sectors of the chemical, pharmaceutical, ceramic, gypsum, wood, and mining industries. Flash dryers are simple in construction and have low capital cost and they are almost trouble free.

• CapacityUpto 60 TPD
• MaterialStainless Steel
• Usage/ApplicationSpray drying is used to dry pharmaceutical fine chemicals, foods, dairy products, blood plasma.
• TypeRotary and Nozzle Type
• Automation GradeAutomatic
• DesignCustomized