SWEIPL brings to its customers Mass Flow Meters for the continuous measurement or feeding of free flowing bulk solids, from pulverized to granulated. Installation of Mass Flow Meters are the best solution especially when environmental conditions i.e. too much dust formation demand a closed system or when constrained by space or too high material temperature utilization of other system are ruled out . The MFM is based on reactive force and has a curved chute to guide the flow of material. Deflection of the particle flow generates a reactive force proportional to the instantaneous flow rate. Chute deflection due to radial acceleration, is detected by a maintenance free strain gauge type load cell. This signal is then electronically processed by microprocessor based Control System WS200/C + WD200 to produce flow rate and total weight value at accuracies better than ±2% & with repeatability of 0.5%. Flow rate 30-600tph Material Temperature 0-260˚C Load cell Strain gauge type accuracy better than 2% AREAS OF APPLICATION ·Chemical Industry ·Food Industry ·Fertilizers Industry ·Metallurgical Industry ·Power Station ·Environment Industry ·Cement Industry ·Building Industry TYPICAL EXAMPLES To measure free flowing bulk solids such as Cement, Fly Ash, etc during Load Out. To measure recycles from Cement Grinding Mills when the measuring signal may be used to control the addition of fresh material. To feed Raw Meal to Heat Exchanger or Rotary Kiln in Cement Factories.

• Belt Width600 to 1600 mm
• Capacity10 t/h to 5000 t/h

• Flow Rate100Kg/h to 15t/h

The Weigh Feeders –DPRC & DPN are suitable for installation directly under the silos in industrialized environment with light & heavy duty conditions respectively.High quality measurement and control electronics allow both convenient operation and extensive monitoring, assuring high accuracies of feed. Belt weigh feeders are able to control in continuous mode, the flow of the discharged material maintaining the instantaneous flow rate constant with respect to the set rate.

• Flow Rate6t/h to 15t/h
• Range Feed1:10 in AC/1:20 in DC

• Flow Rate100Kg/h to 15t/h

The Weigh Feeders –DPRC & DPN are suitable for installation directly under the silos in industrialized environment with light & heavy duty conditions respectively.High quality measurement and control electronics allow both convenient operation and extensive monitoring, assuring high accuracies of feed. Belt weigh feeders are able to control in continuous mode, the flow of the discharged material maintaining the instantaneous flow rate constant with respect to the set rate.

• Range Feed1:10 in AC/1:20 in DC
• Flow Rate6t/h to 15t/h

• Capacity10 t/h to 5000 t/h
• Belt Width600 to 1600 mm

SWEIPL brings to its customers Mass Flow Meters for the continuous measurement or feeding of free flowing bulk solids, from pulverized to granulated. Installation of Mass Flow Meters are the best solution especially when environmental conditions i.e. too much dust formation demand a closed system or when constrained by space or too high material temperature utilization of other system are ruled out . The MFM is based on reactive force and has a curved chute to guide the flow of material. Deflection of the particle flow generates a reactive force proportional to the instantaneous flow rate. Chute deflection due to radial acceleration, is detected by a maintenance free strain gauge type load cell. This signal is then electronically processed by microprocessor based Control System WS200/C + WD200 to produce flow rate and total weight value at accuracies better than ±2% & with repeatability of 0.5%. Flow rate 30-600tph Material Temperature 0-260˚C Load cell Strain gauge type accuracy better than 2% AREAS OF APPLICATION ·Chemical Industry ·Food Industry ·Fertilizers Industry ·Metallurgical Industry ·Power Station ·Environment Industry ·Cement Industry ·Building Industry TYPICAL EXAMPLES To measure free flowing bulk solids such as Cement, Fly Ash, etc during Load Out. To measure recycles from Cement Grinding Mills when the measuring signal may be used to control the addition of fresh material. To feed Raw Meal to Heat Exchanger or Rotary Kiln in Cement Factories.