Down-Hold Clamps With Cranked Clamping Lever EH 23210.

The quick-acting clamping element simultaneously presses the workpieces towards both, the stops and fixture plate. The low profile construction enables the entire surface to be machined. In conjunction with cylindrical stops EH 23280., a special fixture can be replaced. MaterialSteel, case-hardened, blackenedNotesRoHS compliantREACH compliantFree of conflict minerals

View Complete Details

Ask Latest Price & Details

Down-Hold Clamps Without Clamping Lever EH 23210.

By tightening the ball-ended thrust screw the workpiece is simultaneously pressed towards the stops and fixture plate. The favourable leverage enables high horizontal clamping forces. When using T-nuts EH 23010. EH 23020. (DIN 508) they can also be applied to other slot sizes. MaterialSteel, case-hardened, blackened, groundNotesRoHS compliantREACH compliantFree of conflict minerals

View Complete Details

Ask Latest Price & Details

Down-Hold Clamps Without Clamping Lever, With Support EH 23210.

Down-Hold Clamps - without clamping lever, with support_DrawingsBy tightening the ball-ended thrust screw the workpiece is simultaneously pressed towards the stops and fixture plate. The favourable leverage enables high horizontal clamping forces. When using T-nuts EH 23010. EH 23020. (DIN 508) they can also be applied to other slot sizes. MaterialSteel, case-hardened, blackened, groundReferencesThe integrated support is equipped with a location thread to fit for example screwed rest buttons EH 22690., self-aligning pads EH 22730. EH 22740.

View Complete Details

Ask Latest Price & Details

Sub-Part Clamps EH 23211

The sub-part clamp and the sub-part stop enable workpieces to be clamped on the front face. This allows the full area of the machine table to be used to clamp the workpiece. down-hold effect through an angled jaw face clamping of large workpieces on the whole of the machine table large clamping forces of up to 20 kN solid version made of vibration-eliminating ductile iron optimal adaption to the workpiece and material through the use of clamping inserts and interchangeable jaws force closure is possible with a fixed slot tenon EH 23110. in a T-slot minimum interference of clamping areas - even for large workpieces location holes at the sides for fastening of longitudinal stops if required MaterialDuctile cast iron (GGG 60)

View Complete Details

Ask Latest Price & Details

Push-/Pull Clamps EH 23229.

The clamp is suitable for easy and safe positioning of workpieces or components prior to clamping or assembly. As the pushpull clamp is threaded on both sides it is possible to fix elements that are adapted to the workpiece, e.g. prisms, clamping bolts, self-aligning pads. MaterialPin Steel, blackenedBody Steel, zinc-coatedSpring Stainless steel 1.4310

View Complete Details

Ask Latest Price & Details

Floating Clamps

The floating clamp is used to clamp and support additional clamping points on components. The benefits of the floating clamp are: especially suitable for large workpiecesavoids vibration during the processingclamps ribs, beads and shackles to reinforce clamped componentsdistortion-free clamping of raw partsMaterialHousing Aluminium, red anodisedBody Case hardened steel, nitrided, manganese phosphate treated and groundClamping Jaws Case hardened steel, nitrided, manganese phosphate treatedAssemblyMount the floating clamp (M 16 connection thread) onto the device with a wrench (WS 55). Adjust the height limit stop and the rotating area with the red sleeve and clamp with a set screw (3 x WS 3). When setting the height limit, consider tolerance of workpiece.

View Complete Details

Ask Latest Price & Details

Eccentric Clamping Clamps EH 23270.

Eccentric Clamping Clamps_DrawingsThese clamps have a high clamping force for low clamping heights. The body from brass provides a gentle but safe clamping. MaterialEccentric screw SteelBody Brass

View Complete Details

Ask Latest Price & Details

Eccentric Clamps

The eccentric clamp allows clamping with pull-down effect on different workpiece forms at low height. MaterialCase-hardened steel, case-hardened and blue zinc-coatedAssemblyManufacture a thread with the corresponding distance L2 L3 to the workpiece.Screw in the eccentric clamp at the necessary height and set it relative to the workpiece with its flat side.Insert the workpiece and tighten the clamping pin using the internal hexagon. The proper tension is achieved after approx. 13 turn.The threaded hole must be lubricated on a regular basis. The rotational movement during tightening must always be completed towards the stops in order to prevent the workpiece from turning away from the stops.

View Complete Details

Ask Latest Price & Details

Eccentric Quick Clamps With Female Thread EH 23390.

For quick and easy clamping and releasing of workpieces. When using the "adjustable" design (picture 2) the lever position can be moved. MaterialSupport washer Thermoplastic PA, glass-fiber reinforcedThermoplastic POM, glass-fiber reinforcedLever Zinc die-cast, plastic coated, blackThreaded part Steel, galvanisedStainless steel 1.4305Inner parts Steel, galvanisedStainless steel 1.4305Adjusting nut Steel, galvanisedStainless steel 1.4305NotesRoHS compliantREACH compliantFree of conflict minerals

View Complete Details

Ask Latest Price & Details

EH 23390 Eccentric Quick Clamps

For quick and easy clamping and releasing of workpieces. When using the "adjustable" design (picture 2) the lever position can be moved. MaterialSupport washer Thermoplastic PA, glass-fiber reinforcedThermoplastic POM, glass-fiber reinforcedLever Zinc die-cast, plastic coated, blackInner parts Steel, galvanisedStainless steel 1.4305Screw Steel, galvanizedStainless steel 1.4305Adjusting nut Steel, galvanisedStainless steel 1.4305NotesRoHS compliantREACH compliantFree of conflict minerals

View Complete Details

Ask Latest Price & Details

Eccentric Clamps EH 23410.

The eccentric lever can be adjusted to the best position by means of the serration. By removing the washer the eccentric clamp can also be used as an infinitely adjustable stop. MaterialBody Steel, case-hardened, blackenedStainless steel 1.4305, nickel-platedScrew Steel, hardened, blackenedStainless steel 1.4021, heat-treated, nickel-platedBall knob Thermosetting plastic PF 31, black, DIN 319

View Complete Details

Ask Latest Price & Details

Down-Thrust Clamps

The down-thrust clamps provide the following advantages: Rapid manual clamping by means of clamping screw, adjustable clamping lever or adjustable eccentric quick clamp.Easy and quick changing of the workpiece by swinging the clamping head to the left or right.Reduced space requirements due to the compact design.Easy adaption even to larger clamping heights by means of height adjusting cylinders.MaterialCase-hardened steel, case-hardened, blackened and groundAssemblyDown-thrust clamps can be fastened in two different ways: with a nut for T-slots (DIN 508)with a set screw directly in the mounting plate e.g. of a fixtureThe cylinder has to rest on the entire surface. ReferencesThe clamping height can be increased with EH 23310. height adjusting cylinders and EH 1007. washers, and equally lowered by using clamping elements e.g. EH 22730. Further productsHeight Adjusting CylindersSpacers

View Complete Details

Ask Latest Price & Details

Compact Clamps EH 23690.

The compact clamps are all purpose clamping elements. Due to the self-locking clamping lever application can either take place in horizontal or vertical position in both, machined and raw workpieces. Features: exact and position precise clampingease of operationhigh clamping force at low tightening torques, abrasion-resistant due to clamping lever with bearingscontinuous, large clamping areaclamping lever entirely retractable for hindrance-free exchange of workpiecesthreaded clamping lever can be used with many clamping elements, e.g. ball-ended thrust screws (EH 22700. - EH 22720.), self-aligning pads (EH 22730.EH 22740.) etc.large adjusting range at constant clamping forcecontinuous height adjustment by height adaptors 23690.0112.0116easy and flexible set upcorrosion-resistantresistent to dirt and chips

View Complete Details

Ask Latest Price & Details

Shaft Clamps EH 23341.

Shaft Clamps_DrawingsShaft clamps used to clamp round workpieces, e.g. shafts, axels, tubes or rods voth axially and radially. MaterialBody Steel, blackenedClamping screw Steel, zinc-coated (DIN 912)AssemblyExpand the clamping jaws to the diameter of the shaft to be clamped.Insert shaft clamp into hole using the assembly tool.Insert and position the shaft.Clamp using cylinder screw WS (observe tightening torque).NotesThe thread d3 serves to hold the assembly tool (optional).

View Complete Details

Ask Latest Price & Details

Clamps #4567286

Down-Hold Clamps With Cranked Clamping Lever EH 23210.

Down-Hold Clamps Without Clamping Lever EH 23210.

Down-Hold Clamps Without Clamping Lever, With Support EH 23210.

Sub-Part Clamps EH 23211

Push-/Pull Clamps EH 23229.

Floating Clamps

Eccentric Clamping Clamps EH 23270.

Eccentric Clamps

Eccentric Quick Clamps With Female Thread EH 23390.

EH 23390 Eccentric Quick Clamps

Eccentric Clamps EH 23410.

Down-Thrust Clamps

Compact Clamps EH 23690.

Shaft Clamps EH 23341.

Contact Us