S S Power System

Ecotech, Greater Noida, Uttar Pradesh

It is used to overcome problems likes single phasing, reverse phasing and unbalance supply to protect the electrical/electronic appliances.

Features :

• Auto cut off on single phasing & unbalances supply.
• Auto corrects in Reverse phasing
• Switching time is 10 second with an Operating Voltage 130V to 280V.
• Temper proof and maintenance free, powder coated box.
• Microcontroller based technology with Pre Program interlocking to prevent short circuit.
• Minimum heat dissipation & energy losses.
• Remove problem of sparking & burning with the usage of Pre Magnetic Contactor.

SUBTECH makes CLD cum auto changeover, which is a fully automatic high precision system for efficient distribution of individually rationed generator power, an advantageous and cost-effective alternative to conventional manual changeovers. The auto changeover cum current limiting device (CLD) works as a changeover and also gives protection to the generator due to overload and abnormal supply. It is a Micro-controlled Pre-Programed overload protection system for multiple operations, mostly used for generators and power backup in multi-storied societies, malls, apartments, etc.

Features:

• Settable voltage range for mains and Genset
• Settable overload limit for genset
• The auto trip on overload to prevent genset overloading
• Overload trip time will decrease as overload increase
• Once tripped, auto re-starts after 10 seconds (max), and so on upto 5 trials
• An auto trip on under/over voltage on mains and genset to avoid damages to appliances
• Continue glowing LEDs in healthy conditions & blinking LEDs on source waiting and faulty conditions
• After 5 trials, tripped permanently for 3 minutes
• Automatically tries again after 3 min or the user can reset manually or wait for the mains
• Safeguards generator by gradual loading and precision monitoring
• Assured availability of allotted currently; no less, no more
• Significant savings on wall space and wiring.

Auto changeover the need for continuous power supply and its reliability has increased rapidly over the years, especially in all those areas where continuous power supply is must. Their complexity has increased as continuous information and communications are needed to control automated process, be in industries, commercial complexes, hospitals, hotels or even modern residences. Automatic Changeover from main supply to stand by supply is vital for all the above kinds of load. In case of both DG Supply as well as mains supply, comes together then priority will be of mains because the automatic changeover will change DG supply to mains. In the event of power failure, the standby power is usually expected to take over automatically. Electrical starting equipment, battery bank and diesel generator are required for the automatic operation. The automatic transfer is achieved mostly by AMF Panels. The process of on-load transfer has to be monitored & controlled for a smooth Changeover and within safety limits of all elements of the system.

Features:

• Operating Voltage 130V to 280V
• Inbuilt SMPS supply to operate the circuit
• Simplifies electrical complexity with NFC System
• LED Indication for MAINS ON & GENERATOR ON
• Potential free contact for Start/stop of generators (optional)
• Genset Stop system is inbuilt, especially for Portable Generators
• Time Delay on generator mode in changeover in higher capadty
• When main supply is resumed, the connected load is automatically shifted to mains
• Powder Coated 130 Compact size Wall mounting, Temper proof and maintenance free
• Microcontroller based technology with Pre-Program interlocking to prevent short circuit.
• Single Phasing does not affect the overall output: Only the absent phase of mains will fail in output, not all three phases will fail
• Switch over time for genset to main is very minimum so that even sensitive equipment's do not get "OFF" during the switch over
• Its unique circuit design enables the relay to be in 'ON' position only while the genset is in use. During main supply the relay remains in 'OFF' position. Due to this the life of changeover gets increase.
• No Time Delay for output on resumption of Mains Supply whenever DG's not working. In that time Interval as load remain connected to the mains only. (Even in the absence of one or two phase also)
• DG Supply can/cannot be used at the time of single phasing of Mains supply. (Because some users are satisfied even in single phase to save the diesel cost.)
• In the Presence of supply in all three phase, load automatically shifts from DG to Mains with a time delay of 5 Sec. But when there is one or two phase supply, Load will not shift from DG to Mains only.

Digital Time Switches are used where electrical equipment must be periodically switched on and off for pre-programmed daily or weekly times. Digital time switches available with only 5 pin timer. The 5 pin model connection is an AC 220 is just like a switch. It can be used for switching to any application individually or with group of appliances.

Features :

• Digital programmable Daily, weekly timer basis.
• Upto 16 programs daily
• Supply voltage - DC 12V, 24V, AC110-260V Freq50Hz
• Inbuilt rechargeable V80H battery for memory backup means no issue of replacing battery, Battery charge last for at least 1-2 months without charge. i.e. Without AC supply connectivity.
• Led power indicator, LCD on screen displays for on and off switching status.
• Contact single pole - single throw, Contact capacity-16 Amp, 240 VAC.
• Running accuracy 1 second / day at 20, Minimum time setting - 1 minute.
• It can be used for street lights, motors, T.V., AC etc.

Solar pumping system consists of four parts: solar panels, solar pump controller, single phase or three phase pump and water drives AC pump to pump water from borehole, river, lake etc. to the storage device. The inverter applies high efficiency MPPT algorithm to maximize power harvested from solar panels. It will make the system to maximize efficiency to get the water as much as possible.
The solar pumping system fulfills concept of low carbon, energy conservation, environmental protection to improve the living standard in water-deficient area.

We are manufacturer ofSemi/Fully Automatic Pump Controller or water level controller for your home and industry. It continuously monitors the liquid level of the overhead tank and reservoir.The Automatic pump controller controls the water pumps and turns it ON and OFF with respect to the level in the water tank. This auto-switching feature saves manpower. Hence no need to operate manually. There for no wastage of water, stop tank overflow, save water & electricity bill.

Features:

• Auto start &stop according the tank level
• Digital display to show level (in percentage)
• Audio alarm on full tank
• Push button to reset buzzer
• Maintenance free, high quality magneticfloat sensor
• It is suitable for 1/ 3 phase motor.

It is used to maintain power factor by the use of capacitor bank to suit the variations in inductive/resistive loads. Specially in industrial sector, heavy inductive loads are very common to give low power factor, which results in higher demand charges and also low power factor penalties. APFC panel provides automatic switching operation of the suitable capacitor bank for fixing power factor from load fluctuation.

Features :

• User friendly microprocessor based APFC relay.
• Modular design with easier assembly, Installation & maintenance.
• Power factor correction done with help of power factor controller & power contactors by switching In/Out 6/8/12 steps of capacitor banks.
• Used for three phase loads.

Availability : Contactor based and PMC based

SUBTECH series UPVC plastic butterfly valve according to the different medium has a variety of optional material; corrosive resistance is strong, small volume, light weight, extremely non-toxic material. The Mid Stem Structure in this butterfly valve will protect the water leakage from butterfly valve to motor. It is used in industries, multi storied buildings, malls to control the flow of liquids.

Features :

• Can be operated automatically, manually or remotely
• Epoxy resin coating over mid stem structure prevents structure from corrosion.
• Operating Voltage - 130V to 280V.
• Maintenance free
• Can be used for any type of liquid.

Our team of quality analysts strictly tests each product against varied quality parameters ensuring zero defects at buyer's end. Be it online payment or offline, we make possible for you to make trade transactions as per your convenience. We offer both offline and online mediums to make payment.Automatic Battery Charger for charging generator battery automatically with LED indications and fault protections.

Features :

• Trickle and boost mode
• Reverse polarity protection
• Auto cut-off on full charge

Availability

• Transformer Base Battery Charger : 12/24 VDC
• SMPS Base Battery Charger : 12/24 VDC

Salient Features:

• Suitable for charging generators battery
• LED indications
• Fault protection
• Reverse polarity protection
• Boost and trickle modes
• Input volt: 160-260 VAC, 50 Hz