Write a Review
Our Products
Temperature Controller
2 Products availableLaboratory Ovens
2 Products availableIndustrial Ovens & Furnaces
2 Products availableKitchenware And Cookware
2 Products availableMachine And Precision Tools
2 Products availableWe are leaders in the market for providing best range of Thermal Stability, Ageing Oven with Digital Flow Sensor, Ageing Oven (With Digital Flow Sensor), Ageing Oven and Sample Die for Smoke Density
Thermoplastics and PVC (Plasticized Polyvinyl Chloride) materials when exposed to continuous heat, degenerates and emit harmful acidic gases. The instrument is manufactured for testing PVC materials against their thermal stability at higher temperature.
The insulation material in a cable is used to isolate the conductor from one another and from ground, as well as provide the necessary mechanical strength. The fundamental requirement of the insulation in an electric cable is that it withstand the voltage imposed on it in the service.
Two Roll Mill is used for mixing two or more compounds in a homogeneous mixture. This Mixture is then molded into samples for further testing.
Model Number: SSI 511 TRPFSD
| Two Roll Mill is used for mixing two or more compounds in a homogeneous mixture. This Mixture is then molded into samples for further testing. |
For preparing test sample from two or more materials, they have to be mixed homogeneously. The Two Roll Mill with its two heated rollers, rotating in different directions, at slightly different speeds is an ideal machine for such a work. The test samples can then be obtained from the sheet by using Hydraulic Hot Press, Dumb-bell Dies etc.
Two rollers mounted on a sturdy frame, rotating in different direction at slightly different speeds.
Roller Size: 6 dia, 12 Length.
Two PID Controller for heating control one for each roller.
Heating by especially designed U shaped heaters.
One 440 V III phase motor with gear assembly for rotating the rollers.
Start / Stop switch and power cord.
Two Emergency Switches, one on panel and one on knee height to reverse the motor in case of any emergency.
Guard plates and funnel on rollers to prevent accidental insertion of operator hand between rollers.
Spatula for mixing the compound.
Thermoplastic and electrometric substances when exposed to heat undergo many types of physical and chemical changes. The extent and type of change that takes place depends upon the severity of exposure of the sample to heat (i.e., temp. range), duration and rate of air flow
Model Number: SSI 510 DPFW
| The Press is deigned to accept various types of Dumb Bell and Sample Dies for cutting the sample. Description The Press can be used with various Dumb Bell and other types of dies to cut the sample from sample sheets. The press is designed to minimize the human effort required to cut the sample, by using the heavy wheel. When the operator turns the wheel, the wheel gains the momentum due to its weight and applies large force on the cutting die. . This type of cutting press is very simple and useful to operate especially for harder sample materials. The press can be installed on top of a table and operated by a single person. The Die cutter can be interchanged by just loosening one LN screw. |
Model Number: SSI 502 AGAN DFS
Standard Number: AS / NZS 1660:2:3IS 10810 Pt 10
| Thermoplastic and electrometric substances when exposed to heat undergo many types of physical and chemical changes. The extent and type of change that takes place depends upon the severity of exposure of the sample to heat (i.e., temp. range), duration and rate of air flow Instrument PrincipleThermoplastic and electrometric substances when exposed to heat undergo many types of physical and chemical changes. The extent and type of change that takes place depends upon the severity of exposure of the sample to heat (i.e., temp. range), duration and rate of air flow. This test makes an assessment of change in Tensile Strength and Elongation of the material on subjecting them to accelerated ageing in hot air. Standard. The instrument is designed to conform to AS/NZS 1660-2-3 .InstrumentEach Cell is a complete instrument in itself i.e., fitted with individual Temp. Indicating Controller, Air Flow Meter, Air temperature controller and an Hour Meter. This enables the user to test different type of samples at desired temperature and duration, depending upon test requirement of end users & testing authorities. Instrument The instrument consists of the following: . A double walled chamber with inside chamber of thick aluminum sheet. Size of the chamber is 100 mm dia. x 300mm ht. Jacket type heater for the chamber. Digital Temp. Indicating Controller with sensor. Temp. rangeAmbient to 200 2oC. Digital Flow meter for controlling the volume of air passing through the chamber. Air inlet nozzle for the airline or air compressor. Specially Designed heaters to heat the air before it enters the cell Separate temperature controllers for air temperature control Air turbulence fan with motor to rotate at 60 RPM Specially designed top cover to hold three to five test samples in each chamber. Hour Meter to record the total time of test. . To operate the unit Compressed Air line is to be provided by the customer. If the customer is using his own air compressor, it may require one pressure regulator, pressure gauge & connecting pipes which are available from us. Difference between Hot Air Oven and Ageing Oven: The test requirement is 8 to 20 air changes per hour, measured on a Flow Meter. According to IS standard, if the Oven does not have a regulated air supply, the oven is then termed as a Hot Air Oven and not a Ageing Oven (as offered by some manufactures) and cannot be used for ageing of samples. After ageing in the ageing test oven for specified temp. & duration the samples are to be tested on Tensile Testing Machine for tensile & elongation. For preparation of Dumb-bell shaped samples, you may require hydraulic hot press, dumb-bell dies, dumb-bell cutting press, two-roll mill etc. Please ask for details. |
Thermoplastic and Poly Vinyl Chloride substances when exposed to heat undergo many types of physical and chemical changes. The extent and type of change that takes place depends upon the severity of exposure of the sample to heat (i.e., temp. range), duration and rate of air flow.
Model Number: SSI 558 VOC
Standard Number: IS: 10810 (Pt.33)
| SSIPLvacuum ovens are required in almost every institution for drying, moisture removal by heating in vacuumed environment. |
SSI 107 Vacuum Oven is a double walled leak proof chamber with inner chamber made of Stainless steel and outer chamber of Mild Steel powder coated. The Heaters are embedded, and are controlled by digital temperature controller for temperature range from 50 to 150 deg C.
Vacuum range 0-30 PSI is achieved by a separate vacuum pump connected to the oven using rubber pipe.
A toughened glass window is provided in the door to view the samples inside without disturbing the thermal / vacuum conditions
A choice of cylindrical / rectangular inner chamber is available as per requirement.
Some of the standard sizes are
| Cylindrical | Rectangular |
| Diameter X Depth | L X B X H |
| 250 X 300 mm | 6 X 6 X 6 |
| 300 X 300 mm | 8 X 8 X 8 |
| 10 X 10 X 10 | |
| 12 X 12 X 12 |
Vacuum Ovens with temperature up to 300C with Stainless steel door / Digital vacuum control with solenoid valves are also available on request.
Model Number: SSI 523
Standard Number: IS 10810 Pt 38IS 10810 Pt 39IS 10810 Pt 3
| During the armoring process and subsequently during laying of the cable, the armor wires are subjected to torsion stress. The test is conducted to evaluate the torsion resistance of the wire. A Unique Machine which conforms to three different test standards. The machine is manufactured as per IS 10810 Pt 38 (Torsion Test On Galvanized Steel Wires For Armoring.), IS 10810 Pt 39 (Winding Test On Galvanized steel Strips For Armoring.) and IS 10810 Pt 3 (Wrapping Test For Aluminum Wires). for wire.
During the armoring process and subsequently during laying of the cable, the armor wires are subjected to torsion stress. The test is conducted to evaluate the torsion resistance of the wire. The wire is attached between the two vices and twisted / turned. The no of turns required to break the wire is then noted.
The Instrument consists of following: Two Vices. Heavy Duty Motor Weight attachment to provide tension to sample Attachment for Winding and wrapping Test complete withweight and Mandrels |
Model Number: SSI 509 HP250
| Various standards for test of Plastics, Wires & Cables, and Polymer Compounds require test samples of specific shape and size for conducting test on different materials. Hydraulic Hot press is a basic apparatus in sample preparation like Dumb-bell shaped specimen for test on a Tensile Testing machine. Instrument PrincipleVarious standards for test of Plastics, Wires & Cables, and Polymer Compounds require test samples of specific shape and size for conducting test on different materials. Hydraulic Hot press is a basic apparatus in sample preparation like Dumb-bell shaped specimen for test on a Tensile Testing machine. A uniform sheet of the material is formed in the press from which different test samples of specific shapes and sizes can be easily made with minimum of effort and wastage of raw material. The Machine can also be used to apply temperature and pressure to any material to mold set or test the physical properties of any material. InstrumentThe instrument consists of the following: Hydraulic Hot Press of250 KNforcecapacity fitted with a manually operated hydraulic oil pressure pump assembly Pressure gauge : Analog : Range 0-250 KN , LC 1.25 KN at 82.5 RAM Diameter. Two electrically heated platens of8 x 8 size (200 mm x 200 mm) Separate Digital Temp. Indicating Controllerwith sensorfor both platens Heaters : Rod Heaters (4 in each platen), 250 / 350 W each. Cooling system in the steel platens (for rapid cooling) Operates on 220 VAC 50-60 Hz. Total load4 KW (max), 16 Amps. Net Weight 120 kg, Gross Weight 150 kg, Box Size 60 x 60 x 80 (LBH in cm) may vary slightly depending on the specification. The Hydraulic Press applies temperature up to 200oC and Force up to 25 KN to press and melt any sample to form sheet as per the mold used. |
model number: ssi 560 sbt
standard number: iec 60245-2:1994
| the test is intended to verify the effectiveness of the separator between the non tinned conductor and insulation. instrument principlethe test is intended to verify the effectiveness of the separator between the non tinned conductor and the insulation. the instrument consist of one pickling bath and one solder bath. The solder bath is designed to maintain a temperature of up to 300oc, as to keep the solder in a molten state. the ample is first dipped in the pickling bath and then dipped in the solder bath for predetermined cycles. The no of dips and the speed of dip can be controlled. standardthe instrument conforms to iec60245-2 : 1994 instrumentone pickling bath one solder bath an automated robotic arm to dip the sample in pickling and solder bath the arm is also designed to transfer the sample form pickling to solder bath plc to control the instrument. hmi for display and interacting with the operator. |
Model Number: SSI 516.1
Standard Number: ASTM D 2843
| Correct and accurate sample is necessary for result accuracy and repeatability. The Sample Die is designed to produce equal sized samples for testing Smoke Density for any sample. The Die is specifically designed to make samples for Smoke Density Test Apparatus. The Die is manufactured in three pieces. The upper and lower plates are support plates. The Middle plate has cut out for the samples as per the standard requirement.
The Die with sample is kept in Hydraulic press for formation of smooth and accurate samples to be tested in Smoke Density . |
Model Number: SSI 510 DBxx
Standard Number: IS 10810 Pt 7, DIN 53504 S2, ISO 37-2, JIS K6251-6, JIS K7162-5A, ISO 527-2-5A, BS 6746(L), IEC 540(L),
| Dumb Bell is the most widely used shape for testing various samples for their physical and other properties. Dumb Bell is the most widly used shape for testing various samples for their phyical and other properties. The Dumb Bell Shape provides excelent grips on both sides.
|
Model Number: SSI 511 TRPFS
| Two Roll Mill is used for mixing two or more compounds in a homogeneous mixture. This Mixture is then molded into samples for further testing. |
For preparing test sample from two or more materials, they have to be mixed homogeneously. The Two Roll Mill with its two heated rollers, rotating in different directions, at slightly different speeds is an ideal machine for such a work. The test samples can then be obtained from the sheet by using Hydraulic Hot Press, Dumb-bell Dies etc.
Two rollers mounted on a sturdy frame, rotating in different direction at slightly different speeds.
Roller Size: 6 dia, 12 Length.
Two energy regulator for heating control one for each roller.
Heating by especially designed U shaped heaters.
One 440 V III phase motor with gear assembly for rotating the rollers.
Start / Stop switch and power cord.
Two Emergency Switches, one on panel and one on knee height to reverse the motor in case of any emergency.
Guard plates and funnel on rollers to prevent accidental insertion of operator hand between rollers.
Spatula for mixing the compound.
Model Number: SSI 549 ULML
Standard Number: UL 94, ASTM D 635, ASTM D 408, ASTM D 3801, ASTM D 5048, IEC 60707, IEC 60695-11-10, ISO 1210, ISO 10351
| The UL test serves as a preliminary indication of a plastics material acceptability for use as part of a device or appliance with respect to its flammability.The instrument is designed for both Vertical and Horizontal burning. |
Model Number: SSI 549 ULMM
Standard Number: UL 94, ASTM D 635, ASTM D 408, ASTM D 3801, ASTM D 5048, IEC 60707, IEC 60695-11-10, ISO 1210, ISO 10351
| The UL test serves as a preliminary indication of a plastics material acceptability for use as part of a device or appliance with respect to its flammability.The instrument is designed for both Vertical and Horizontal burning. Instrument PrincipleUL 94: Test for Flammability of Plastic Materials for Parts in Devices and Appliances This test uses specimen which is held at one end in thevertical or Horizontalposition.A burner flame is applied to the free end of the specimen for two intervals separated by the time it takes for flaming combustion to cease after the first application. Two sets of 5 specimens are tested. The following are recorded for each specimen:
The instrument is designed to conforms to various international standards Horizontal Burning Test : HB (ASTM D 635, D 4804, IEC 707, or ISO 1210) 20mm Vertical Burning Test: V-0, V-1, or V-2 (ASTM D 3801, IEC 707, or ISo 1210) 500w (125mm) Vertical Burning: 5VA or 5VB (ASTM D 5048 or ISO 10351) InstrumentThe Instrument consist of the following
A Double Walled Chamber for sample burning with front glass door A Burner settable at anywherebetween 0- 90oangle Precise gas control system including gas regulator ManualBurner Moving system Sample Holding System (adjustable both vertically and horizontally) Digital Timer for flame application (can be preset for 1 to 99 sec) Digital timer for flame observation after flame is removed. Digit timer for Glow observation after the flame is extinguished Exhaust Fan / Light in the chamber
Basic Design As per UL 94 Inner Chamber Stainless Steel 1m x 1m x 1m (LBH), Volume 1 m3 Burner 100 mm length 9.5 mm ID Burner Movement through a motor driven worm Manual Movement to adjust the burner position with respect to sample Timer system: Flame Application Time : Pre settable from 1 to 99 Seconds Flame Away time : Pre Settable from form 1 to 99 Seconds Cycles : Pres Settable from 1 to 9 Operations: Adjust the burner position with respect to sample using manual burner movement. Manually Ignite the burner Set the test parameters Start the process. Press the Forward switch to take the burner to the sample. The Flame Application timer will start. After flame time is over, there will another beep indicating the operator to move away the burner. The Burner can be moved again to the sample for multiple burning. After required no of cycles, the burner is automatically shut off with a beep. The Timer for After Flame is switched On automatically. When the operator Hold this timer, Glow timer is switched On. |
Model Number: SSI 548 SM
| The machine is used to reduce the thickness of XLPe sheet to prepare final sample sheet of upto 0.8 mm thickness for testing. Instrument PrincipleDifferent test procedures require different sample thickness to be tested. If the sample has to taken out of cable sheathing / the thickness of the sheathing may have to be reduced to achieve the desired thickness. The Slicing / Skewing machine applies the principle ofpush and cut by using two rollers moving in different directionwith a very sharp blade at the other side of the rollers. The distance between the upper roller and the blade determine the final sample thickness. The distance between the upper roller and theblade can be adjusted, for different types of samples. The lower roller is mounted on a spring set, which adjusts according to the sample thickness. This gives the machine flexibility to cut various different thickness of samples and provide final strips of sample between 0.8 mm to 2 mm as per requirement. Instrument The Instrument consists of following: Two rollers mounted on a sturdy frame, rotating in different direction Gearbox for roller movement Height adjustment forupper rollers Hardenedblade for cutting Available in hand operated / motorized versions The slicing machine is capable of slicing samples from 4 mm to 10 mm and give a final sliced strip of 0.8mm to 2 mm as perrequirement. |
Model Number: SSI 511 TRPVS
| Two Roll Mill is used for mixing two or more compounds in a homogeneous mixture. This Mixture is then molded into samples for further testing. Instrument PrincipleUniform mixing of two or more components to make a homogeneous mixture is vital to make samples for testing. The Two Roll Mill with its two heated rollers, rotating in opposite directions, at slightly different speeds is an ideal machine for such a work. The final test samples can then be obtained from the sheet by using Hydraulic Hot Press, Dumb-bell Dies etc. Two Roll Mill is available in various models for specific customer requirement. Various Models are
The Instrument consists of following: Two rollers mounted on a sturdy frame, rotating in oppositeopposite at slightly different speeds. Roller Size:6 dia, 12 Length. Temperature Control : Using two Energy Regulatorsone for each roller. Heater: Heating by especially designed U shaped heaters. Motor: 3Hp, 440 VAC, 3 phase. Gear Assembly : to drive the rollers in opposite directions. Control: Forward Reverse Switch and power cord. Spatula for mixing the compound. Emergency Switch to shut off motor in case of emergency This Model is suitable for PVC and allied material which require heating for melting and mixing. Not suitable for rubber materials which generates heat during mixing. |
Model Number: SSI 502 AGAN IPC
Standard Number: AS / NZS 1660:2:3, IS 10810 Pt 10, IS 10810 Pt 11
| Thermal Ageing Test Instrument helps in study of Ageing Process on various material. Thermoplastic and Poly Vinyl Chloride substances when exposed to heat undergo many types of physical and chemical changes. The extent and type of change that takes place depends upon the severity of exposure of the sample to heat (i.e., temp. range), duration and rate of air flow. Instrument PrincipleThermal Ageing InstrumentThermoplastic and Poly Vinyl Chloride substances when exposed to heat undergo many types of physical and chemical changes. The extent and type of change that takes place depends upon the severity of exposure of the sample to heat (i.e., temp. range), duration and rate of air flow. This test makes an assessment of change in Tensile Strength and Elongation of the material on subjecting them to accelerated ageing in hot air. Standard Thermal Ageing Test Instrumentis especially designed to suit the requirement ofAS / NZS 1660:2:3 Unique Feature This model pf Thermal Ageing Test Instrument has some unique features which separates this from other equivalent models We are using a combination of two RTD to control the Chamber Temperature. Two RTD are placed approx 100mm apart. The PLC picks the temperature reading from these RTD sensor and average them. This average temperature is used for controlling the chamber temperature. . The Thermal Ageing Test Instrument uses IPC (Industrial PC) with 500 GB hard disk. All the data from the four chambers is collected in the IPC and is used to generate result at the end of the test. The Test result provides the average temperature, air flow, air temperature and agitator RPM over the complete test period. It also generates complete DATA Table and DATA Graph for the test period. All the result files can be saved in a pdf format and printed for future reference. Instrument In this model of Thermal Ageing Test Instrument each Cell is a complete instrument in itself i.e., fitted with individual Temp. Indicating Controller, Air Flow Meter, Air temperature controller and an Hour Meter. This enables the user to test different type of samples at desired temperature and duration, depending upon test requirement of end users & testing authorities. A IPC (Industrial PC) withtouch screenis provided to control and Monitor the instrument. The IPC is a complete computer with windows, hand hard drive. This gives the instrument capability to store all the data form the test and present te same in pdf format. Initially the operator is promoted to set the values using Input Panel through IPC . The operator can then monitor the each chamber using Test Panel wherein all the set and present values of the parameters are displayed. The parameters are also displayed using graphical and data representation. The instrument consists of the following: A double walled chamber with inside chamber of thick aluminum sheet.Size of the chamber is 100 mm dia. x 300mm Digital Temp. Indicating Controller with sensor. Temp. range 0-200 2oC Digital Flow meter for monitoringthe volume of air passing through the chamber. Air inlet nozzle for the airline or air compressor. Specially Designed heaters to heat the air before it enters the cell Separate temperature controllers for air temperature control Air turbulence fan with motor to rotate at 60 RPM Specially designed cover to hold three to five test samples in each chamber. Timer System to record the total time of test. To operate the unit Compressed Air line is to be provided by the customer. If the customer is using his own air compressor, it may require one pressure regulator, pressure gauge & connecting pipes which are available from us |
Thermoplastic and Poly vinyl Chloride substances when exposed to heat undergo many types of physical and chemical changes. The extent and type of change that takes place depends upon the severity of exposure of the sample to heat (i.e., temp. range), duration and rate of air flow.
Model Number: SSI 502 AGIS HMI
Standard Number: IS: 10810 Pt.10, IS: 10810 Pt. 11, IEC 60811-1-2
| Thermoplastic and Poly vinyl Chloride substances when exposed to heat undergo many types of physical and chemical changes. The extent and type of change that takes place depends upon the severity of exposure of the sample to heat (i.e., temp. range), duration and rate of air flow. Instrument PrincipleThermoplastic and Poly Vinyl Chloride substances when exposed to heat undergo many types of physical and chemical changes. The extent and type of change that takes place depends upon the severity of exposure of the sample to heat (i.e., temp. range), duration and rate of air flow. This test makes an assessment of change in Tensile Strength and Elongation of the material on subjecting them to accelerated ageing in hot air. StandardsThe Instrument is especially designed to suit the requirement ofIEC: 60811-1-2, IS10810 (Pt 10), IS 10810 (Pt 11) Instrument. Each Cell of Thermal Ageing Oven is a complete instrument in itself i.e., fitted with individual Temp. Indicating Controller, Air Flow Meter, Air temperature controller and an Hour Meter. This enables the user to test different type of samples at desired temperature and duration, depending upon test requirement of end users & testing authorities. The Thermal Ageing Oven instrument consists of the following: . A double walled chamber with inside chamber of thick aluminum sheet. Size of the chamber is 100 mm dia. x 300mm ht. Jacket type heater for the chamber. Digital Temp. Indicating Controller with sensor. Temp. range 0-200 2oC. Digital Flow Sensors with needle valves for controlling the volume of air passing through the chamber. Air inlet nozzle for the airline or air compressor. Specially designed split top cover to hold three to five test samples in each chamber. 7 HMI to display and control the ageing Oven. Blind Thermostat to cut off heaters after 250oC in case of temperature overshoot for each chamber. . To operate the Thermal Ageing Oven unit Compressed Air line is to be provided by the customer. If the customer is using his own air compressor, it may require one pressure regulator, pressure gauge & connecting pipes which are available from us. Difference Between Hot Air Oven and Thermal Ageing Oven:The test requirement is 8 to 20 air changes per hour, measured on a Flow Meter. According to IS standard, if the Oven does not have a regulated air supply, the oven is then termed as a Hot Air Oven and not a Ageing Oven (as offered by some manufactures) and cannot be used for ageing of samples. After ageing in the ageing test oven for specified temp. & duration the samples are to be tested on Tensile Testing Machine for tensile & elongation. For preparation of Dumb-bell shaped samples, you may require hydraulic hot press, dumb-bell dies, dumb-bell cutting press, two-roll mill etc. Please ask for details. |
Model Number: SSI 502 AGAN HMI
Standard Number: AS / NZS 1660:2:3IS 10810 Pt 10IS 10810 Pt 11
| Thermoplastic and Electrometric substances when exposed to heat undergo many types of physical and chemical changes. The extent and type of change that takes place depends upon the severity of exposure of the sample to heat (i.e., temp. range), duration and rate of air flow. Instrument PrincipleThermoplastic and electrometric substances when exposed to heat undergo many types of physical and chemical changes. The extent and type of change that takes place depends upon the severity of exposure of the sample to heat (i.e., temp. range), duration and rate of air flow. This test makes an assessment of change in Tensile Strength and Elongation of the material on subjecting them to accelerated ageing in hot air. Standard. The instrument is designed to conform to AS/NZS 1660-2-3 . InstrumentEach Cell is a complete instrument in itself i.e., fitted with individual Temp. Indicating Controller, Air Flow Meter, Air temperature controller and an Hour Meter. This enables the user to test different type of samples at desired temperature and duration, depending upon test requirement of end users & testing authorities. A 10 touch screen (HMI) is provided to control and Monitor the instrument. The HMI has various screen for control and monitor of the instrument using different parameters.
Initially the operator is promoted to set the values using Input Panel through HMI. The operator can then monitor the each chamber using Test Panel wherein all the set and present values of the parameters are displayed. The parameters are also displayed using graphical and data representation.
The instrument consists of the following: . A double walled chamber with inside chamber of thick aluminum sheet. Size of the chamber is 100 mm dia. x 300mm ht. Jacket type heater for the chamber. Digital Temp. Indicating Controller with sensor. Temp. range 0-200 2oC. Digital Flow meter for controlling the volume of air passing through the chamber. Air inlet nozzle for the airline or air compressor. Specially Designed heaters to heat the air before it enters the cell Separate temperature controllers for air temperature control Air turbulence fan with motor to rotate at 60 RPM Specially designed cover to hold three to five test samples in each chamber. Timer System to record the total time of test. . To operate the unit Compressed Air line is to be provided by the customer. If the customer is using his own air compressor, it may require one pressure regulator, pressure gauge & connecting pipes which are available from us. |
model number: ssi 515 loipm
standard number: astm d- 2863, is 13501, bs 2782 part 141, iso: 4589-2iso: 4589-3nes 714nes 715
| limiting oxygen index / critical limiting oxygen index apparatus is used for determining the minimum percentage of oxygen required to just support flaming combustion of a material at room temperature in fta mode or at higher temperature (up to 400oc) in hfta mode instrument principlelimiting oxygen index / critical oxygen index apparatus is used for determining the minimum percentage of oxygen required to just support flaming combustion of a material at room temperature in fta mode or at higher temperature (up to 400oc) in hfta mode.
the sample is burned in the mixture of nitrogen and oxygen, and the percentage of oxygen required just to support the flaming combustion is recorded through an imported oxygen analyzer, which gives direct oxygen readings. limiting oxygen index apparatus also has a double walled test column of flame resistance glass of 75 mm diameter. Suitable for testing different size of samples infta or hftamode. a digital temperature-indicating controller provided with the instrument controls the temperature for hfta mode. The instrument is manufactured as per theastmspecification and also confirms various other international standards. standardssipl limiting oxygen index / critical oxygen index conforms to astm d- 2863, bs 2782 pt 141, is 13501, iso 4589-2, iso 4589-3, nes 714 and nes 715. instrumentthe limiting oxygen index / critical oxygen index instrument comprising of
the sample is ignited using the l shaped burner and oxygen % is adjusted till the sample starts to burn like a candle i.e. Sustained burning without extinguishing or rapidly spreading the flame. the sample should burn in this condition for at least 3 mins. at higher temperature the requirement of oxygen for combustion reduces. The environment around the sample is heated using double walled chimney with heaters for hfta test. The procedure to determine the loi remains the same as for ambient temperature. Reading are obtained for various temperatures and oxygen % vs temperature graph is plotted. |
Additional Information:
Payment Terms : T/T
Packaging Details : Packed in Wooden Box.
Delivery Time : 4 to 6 Weeks
Model Number: SSI 502 AGIS
Standard Number: IS: 10810 Pt.10, IS: 10810 Pt. 11, IEC 60811-1-2
| Thermoplastic and Poly vinyl Chloride substances when exposed to heat undergo many types of physical and chemical changes. The extent and type of change that takes place depends upon the severity of exposure of the sample to heat (i.e., temp. range), duration and rate of air flow. Instrument PrincipleThermoplastic and Poly Vinyl Chloride substances when exposed to heat undergo many types of physical and chemical changes. The extent and type of change that takes place depends upon the severity of exposure of the sample to heat (i.e., temp. range), duration and rate of air flow. This test makes an assessment of change in Tensile Strength and Elongation of the material on subjecting them to accelerated ageing in hot air. StandardsThe Instrument is especially designed to suit the requirement ofIEC: 60811-1-2, IS10810 (Pt 10), IS 10810 (Pt 11) InstrumentEach Cell of Thermal Ageing Oven is a complete instrument in itself i.e., fitted with individual Temp. Indicating Controller, Air Flow Meter, Air temperature controller and an Hour Meter. This enables the user to test different type of samples at desired temperature and duration, depending upon test requirement of end users & testing authorities. The Thermal Ageing Oven instrument consists of the following: . A double walled chamber with inside chamber of thick aluminum sheet. Size of the chamber is 100 mm dia. x 300mm ht. Jacket type heater for the chamber. Digital Temp. Indicating Controller with sensor. Temp. range 0-200 2oC. Rotometer for controlling the volume of air passing through the chamber. Air inlet nozzle for the airline or air compressor. Specially designed split top cover to hold three to five test samples in each chamber. Hour Meter to record the total time of test. . To operate the Thermal Ageing Oven unit Compressed Air line is to be provided by the customer. If the customer is using his own air compressor, it may require one pressure regulator, pressure gauge & connecting pipes which are available from us. Difference Between Hot Air Oven and Thermal Ageing Oven:The test requirement is 8 to 20 air changes per hour, measured on a Flow Meter. According to IS standard, if the Oven does not have a regulated air supply, the oven is then termed as a Hot Air Oven and not a Ageing Oven (as offered by some manufactures) and cannot be used for ageing of samples. After ageing in the ageing test oven for specified temp. & duration the samples are to be tested on Tensile Testing Machine for tensile & elongation. For preparation of Dumb-bell shaped samples, you may require hydraulic hot press, dumb-bell dies, dumb-bell cutting press, two-roll mill etc. Please ask for details. |
Model Number: SSI 510 DPLT
| The Press is deigned to accept various types of Dumb Bell and Sample Dies for cutting the sample. Description The Press can be used with various Dumb Bell and other types of dies to cut the sample from sample sheets. The press is designed to minimize the human effort required to cut the sample, by using the lever mechanism. The long handle lever press the piston, on which the cuttingDie is bound. This type of cutting press is very simple and useful to operate especially for soft sample materials. The press can be installed ontop of a table and operated by a single person. The Die cutter can be interchanged by just loosening one LN screw. |
When the Cables / Electrical Equipments are subjected top extreme cold for a considerable duration of time, they may become hardened and stiff. Such hardness and stiffness cause cracking of the insulation or sheath and may lead to failure of cable / equipments.
Model Number: SSI 515.2
Standard Number: ASTM D- 2863IS 13501
| Double walled Borosilicate Glass Chimney provides the ideal test environment for testing Limiting Oxygen Index for at both ambient as well as elevated temperature. The Glass Chimney is designed to test the material for limiting Oxygen Index at Ambient as well as Elevated Temperatures. The Temperature in the chimney is achieved using two heaters.
The First heater heats the gas mixture before it hits the sample. The Second heater heats the environment around the sample for reading at elevated temperature.
The Temperature in monitored using a specially designed U shaped thermocouple and is controlled using PID Digital Temperature Controller. |
Model Number: SSI 507 CCHC
| Test Samples are required to condition at regulated temperature and humidity conditions before the actual test. The conditioning helps reduce the variation in results due to external environmental conditions. Test Samples are required to condition at regulated temperature and humidity conditions before the actual test. The conditioning helps reduce the variation in results due to external environmental conditions.
The conditioning chamber is designed to work at temperature from +5 to + 50 Deg C and 30% to 90% humidity. The temperature is controlled using combination of cooling compressor and strategically placed heater around the inner chamber. Steam generator is used to control the humidity and cooling coils are used to dehumidify the chamber.
The instrument consists of SS Inner Chamber Standard refrigeration system to maintain low temperature Heaters Steam Generator Digital Temperature Indicating controller Digital Humidity indicating controller |
S.S. Instruments Pvt. Ltd. (S.S. Instruments Pvt. Ltd.)
209 Triveni Complax, E-10-12, Jawahar Park, Laxmi Nagar, Delhi – 110092., India
Share us via
View Contact Number 
