ULTRAMAX INDIA

Exhibition Road, Patna, Bihar

Description:Ultra Tile Fix is a polymer engineered grey cement based water resistant adhesive for interior or exterior fixing of a wide range of tiles on to a variety of substrates. Ultra Tile Fix Floor Tile Adhesive is a flexible, general purpose polymer modified, cement based adhesive used for most internal external floor applications including bathrooms, toilets, laundries, kitchens, decks, verandahs and existing tiles. Suitable over concrete, cement renders, screeds, fibrous cement sheeting and Ultra Tile Fix approved waterproofing membranes. When using Ultra Tile Fix Floor Tile Adhesive with translucent tiles, the colour of the adhesive should be taken into consideration. Typical Application Uses:Interior or exterior fixing of a wide range of tiles on to a variety of substrates.Internal external floor applications including bathrooms, toilets, laundries, kitchens, decks, verandahs and existing tiles, Gypsum plaster, plaster boards and cement fibre-board Cement render, concrete and blockwork AdvantagesGood Initial Grab And Non-slipVery High Bond StrengthVibration ToleranceWater ResistantHighly FlexibleIndoor & OutdoorFixes All Tile TypesAny Tile Any SurfaceWater FeaturesTile Over Tiles

Description ultracrete ept-031 is a superior quality rapid hardening admixture. Ultracrete ept-031 are an important component of concrete, together with the cement, water, aggregates ept-031 are used to increase the initial rate and speed of the chemical reaction between cement and the mixing water. This results in a faster stiffening of the concrete (water reducing & rapid hardening admixture) or faster hardening and strength development (hardening admixture) or both.this environmental product declaration covers hardening admixture for normal concrete. Ultracrete ept-031 specially developed for application in pre-cast concrete, high performance concrete and for manufacturing of cement tiles, paver blocks etc. Advantages the maion function of ultracrete ept-031 are as under:1) reduces setting time : depending on the dose and ambient temperature2) reduces water up to 15%.3) improves workability at a given wc ratio.4) quick setting of cement5) gain early hardening and extra compressive strength.6) early mould release.7) time saving.8) increasing production.9) minimizing breakage.10) easy to dose.11) used to avoid hydration delay in winter especially

DescriptionPLSTO-S441 is based on hyper plasticising sulphonated synthetic polymers Uses:PLSTO-S441 is recommended in all high grade concrete which has a cement content of over 400kg m3PLSTO-S44 is recommended in hot weather concreting where workability retention over long periods are required.PLSTO-S441is recommended in marine structures, pile foundations, bridge girders, high rise structures and such structures where quality of concrete is of prime importance.PLSTO-S441 is also recommended where very high initial and ultimate strengths are expected. Advantages Hyper plasticizing action of this product produces free flowing Concrete, With Most Kinds Of Aggregates And Varying Fine Aggregates.PLSTO-S441 Maintains The Workability Over Long Periods.PLSTO-S441 Helps In Production Of High Quality Concrete Which Exhibits Superior Compressive, Tensile And Flexible Strengths And Exhibits Excellent Resistance To Chloride And Sulphide Attacks On Concrete.PLSTO-S441 Is Compatible With All Types Of Cements Including Puzzolonic And Fly Ash Slag Cements.PLSTO-S441 Is Specially Suggested In All High Strength Concrete And In Construction Of Marine Structures, Pile Foundations And Bridge Girders.PLSTO-S441 Enables Production Of Dense Impermeable And Fair Finish Concrete.Upto 20-25% water reduction is possible

DescriptionS2-305 is made under the management of competent experts by consuming the finest grade component according to the market norms. S2-305 is plasticising accelerator for cement concrete and mortars Uses:S2-305 is an accelerator suitable for dry as well as wet spray applications. It is used for the following main applications : S2-305 is of special use in guniting and shot-creting as its accelerated setting times help in quick rebuilding of mortar layers without colla-pseRebound losses in shot-creting and guniting are minimizedEarly shifting of the pre-cast elements is facilitatedIn pre-cast hollow solid blocks, pavers, cement tiles, breaking of the edges while lifting the moulds is minimizedS2-305 helps in early setting of mortars and concrete in low temperature climates Advantages Following arguments specially distinguish S2-305 as catalyser of spraying concrete :Free from alkaliGood long term strength and durabilityIn case of proper application, minimum loss of solidity of the catalysed concreteReduction of reboundImproved adhesion of the sprayed concrete on rock and concreteImproved adhesion in the over head crown portionClear reduction of dust and a good working environmentFree from chloride and does not attack reinforcement

DescriptionUltracrete MR-SB is a chemical release agent suitable for shutters and moulds. Clean release gives a fair faced concrete surface. Ultracrete MR-SB reacts chemically with cement in such a manner that excellent release properties are imparted to the treated face of the shutters and moulds. Concrete casted with Ultracrete MR-SB on the shutters have smooth, hard uniform and light coloured finish. The adhesion of subsequent finishes such as renders, paints or textured coating is unaffected by use of Ultracrete MR-SB UsesUltracrete MR-SB is suitable for all types of shutters and moulds. MR-SB can be applied to steel, timber, plywood, plastic and rubber moulds. AdvantagesUltracrete MR-SB gives very good shutter releasing properties. Other oils used in similar application penetrate into the concrete and interfere with the strength of the member. Apart from this they leave ugly stains on the concrete surface. Before subsequent finishes one needs to chemically or mechanically remove these stains and leftovers of these oils. Ultracrete MR-SB is designed keeping all these problems in mind and to ensure least damages to the shutters and to the concrete. Application of conventional mould releasing oils is tedious and time consuming. Ultracrete MR-SB can be sprayed saving time and labour. Directions For UseWhen using for the first time spray Ultracrete MR-SB on the shutters while erecting them and just before concreting. Thereafter Ultracrete MR-SB can be sprayed just after deshuttering and cleaning. During initial uses new commercial ply shutters tend to be absorptive. Hence it is necessary that new ply shutters are sprayed just before concreting also.