Delhi, India
Our Products
Our offered Product range includes Loop Sterilizer, electrically heated vertical steam sterilizer, Glass Beads Sterilizer, H.P. Cylinderical Horizontal Sterilizer and H.P. Rectangular Horizontal Sterilizer.
Jindal loop sterilizer is an electrical sterilization system most suitable for the sterilization of inoculation loops, needles and instruments. It is ideal for laboratories and safety cabinets where the use of gases and open flames is not permitted.
Robust and temperature-shock resistant
The sterilizing tube, which is made of wear-resistant quartz glass, reaches its optimal temperature of 900°C (1650°F) after only a few minutes. To sterilize the inoculation loop, simply insert it into the quartz tube. After 5-7 seconds, the inoculation loop is sterilized. Any residue remaining on the smooth surface of the quartz tube can be removed easily.
Flexible and safe
The low and stable housing facilitates ergonomic operation; the unique design protects the working surface from contamination.
Technical Data
Chamber Diameter: 14mmSterilization Time: 5-8 secondsMaximum Temp. : 900°CElectrical Supply: 220V/110V Single Phase AC Supply.
At a Glance:
High pressure electrically heated vertical steam sterilizer used for sterilizing of surgical instruments, dressing material, linen, rubber, plastic material, injection liquids by means of steam under pressure of 5 to 20 pounds/sq.inch (PSI) which is adjustable.
Construction
Triple walled with inner chamber, outer wall, and steam jacket made of thick stainless steel sheet. The lid is made out of Stainless steel plate and closed by wing nuts arrangement. Jacket is insulated by high grade glass wool to minimise the temperature loss. All sterilizers are hydraulically tested up to 2.5 times of working pressure.
The instrument is fitted with pressure switch to control the pressure of the chamber.
The sterilizer is fitted with safety valve, water level indicator, and water inlet and drain valves. The sterilizer is supplied complete with cord and plug.
The instrument is designed to operate on 220V AC Supply (Model with 110V also available).
Optional Accessories
| Dia | × | Depth | Load |
| 300 | × | 500 mm | 3.0 kw |
| 400 | × | 600 mm | 4.0 kw |
| 550 | × | 750 mm | 5.0 kw |
Jindal Glass bead sterilizer follows a scientific method for total sterilization of your instruments within 5 to 15 seconds. These sterilizers are compact state of the art, steam less non hazardous equipment for your clinic. It is a simple device for quick sterilization of small instruments with effective thermal sterilization. In this the clear glass beads are used in the well. The temperature of the glass beads sterilization is 240C. The instruments are dip in the glass beads for the quick sterilization. Effective thermal insulation keeps the outer cover cool while keeping an even temperature inside the well. The heat loss is very low thus leading to very low power consumption.
After switching on the device, in approximately 20 minutes the device will reach the proper temperature. The ready indicator will switch on indicating that the sterilizer is ready for use. The green light will be off and on indicating whether the heater is working or not to maintain the temperature of the glass beads in the well.
Introduction
The sterilizer is based on the principle that microbiological action of saturated steam at elevated temperature is rapid and through. All models work on the principle of downward displacement of air which is the most economical method of obtaining sterilization. Robust and rigid construction, designed for all types of bulk sterilization which are commonly needed in Medical, Agricultural and Pharmaceutical Institutions. The sterilizer is suitable for Sterilizing hospital dressings, linen, rubber, plastic goods, surgical instruments, glassware, utensils etc.
Construction
The sterilizer is triple walled with steam jacket and separate boiler. The inner chamber and steam jacket are made up of Heavy gauge Stainless Steel sheet with leak proof argon welding.The sterilizer has single piece door made of stainless steel plate. Back plate and ring is also made of thick stainless steel. All the sterilizers are hydraulically tested to withstand 2.5 times the working pressure. The sterilizer is mounted on tubular steel frame with ground levelling screwed flanges. The Outer jacket is wrapped with glass wool to minimise the heat losses due to radiation and is covered by polished stainless steel sheet for that elegant appearance.
Steam Generator
The steam generator is made of heavy stainless steel sheet. Heavy ring mounted in front of the boiler with removable thick stainless steel plate is fitted with heating elements and low water level cut-off device to protect these elements from burning out dry.Front removable plate system provides easy cleaning of the deposited scale on the elements and the walls for long life and efficiency. The boiler is fitted with water gauge glass for water level indication, water inlet and outlet valves.
Pressure Control
The "PIEZOSTAT" (Pressure control device) is incorporated in all sterilizers. It acts as a safety device, economises on power consumption and reduces the frequent opening of the steam release valve and thus prevents the release of steam in the room, It cuts off the power supply to heaters when the set pressure is achieved and re-energises the heating elements when pressure falls below the set point.
Heating Elements
Flanged types, immersion heating elements are made of high grade material.
Safety Door
Sterilizer has hinged self-locking single piece thick Stainless Steel plate door and cannot be opened when under pressure. The self-locking device automatically disengages the thread mechanism when the sterilizer is under pressure to preclude any eventuality of accident.
Single Point Control
Complete sterilizing cycle is controlled from one point with the help of "Multiport Valve" fitted at front top. Two speeds of steam exhaust are available; fast and slow.Easily readable jacket and chamber pressure on gauges mounted on the left and right of the multi port valve. A moisture trap fitted in the chamber discharge line absorbs the condensate automatically to prevent moistening of the subject matter to be sterilized.
Control Panel
The control panel includes a pressure switch, a microprocessor based digital temperature indicator cum controller, Mains MCB, pilot lamps, relays etc. and mounted on the stand of the sterilizer for easy operation.
Other Features
Operating Temp. & Pressure
Sterilizing Temp : 121C
Sterilizing pressure : 1.2 to 1.5 kg/cm2 (15 psi to 22psi)
Power Requirement : Designed to operate on 415V volts, Three phase AC supply
Available in following capacities
Introduction
The sterilizer is based on the principle that microbiological action of saturated steam at elevated temp is rapid and thorough. All models work on downward displacement of air principle which is most economical method of obtaining for all types of bulk sterilization which are commonly needed in Medical, Agricultural and Pharmaceutical institutes.
It is suitable for sterilizing hospital dressings, linen, rubber plastic goods, surgical instruments, glassware and utensils etc.
Construction
The sterilizer has a robust and rugged all weld construction which is leak proof. The inner chamber is made of thick plate of stainless steel of high quality and jacket is made out of rolled stainless steel sheet. Sterilizers will have single door made out of thick stainless steel plate. All the sterilizers are hydraulically tested to withstand 2.5 times the working pressure.The steam jacket is lined on the outer side with glass wool which prevent heat losses due to radiation and is covered by strong rolled steel sheet duly powder coated.
Boiler
Made of thick stainless steel plate suitably located under the sterilizer. High grade flanged type heating elements are fitted from front side for easy replacement/repair. Fitted with water gauge glass for water level, safety valve, water inlet and drain valves. It is also provided with Low Water Level cut off device. This device protects the heater in the generator from burning out dry. The steam pressure in the boiler is indicated on an individual pressure gauge.
Safety Lock for Door
Every horizontal rectangular sterilizer is fitted with SELF LOCKING SAFETY DOOR which cannot be opened when the chamber is under pressure.The clutch mechanism automatically disengages the threads of the radial locking system for precluding any eventuality of accident when the chamber is under pressure. A heat resistant Neoprene Rubber gasket ensure steam tight fitting.
Pressure Control
Electrically operated "PIEZOSTAT" (Pressure Control Device) is incorporated in all sterilizers. It acts as a safety device, economises power consumption and limits the use of release valve which would frequently blow steam into the room.It cuts off the power supply to heaters when the set pressure is achieved and re-energises heaters when pressure falls down.
There is no effective medical care without sterile instruments. Non-sterile instruments spread diseases between patients.
Many developing countries still use non-sterile instruments. Alcohol or boiling water does not kill all viruses and bacteria. Regular autoclaves consume much energy and require distilled water, which both are in short supply in developing countries.
Jindal Infrared Sterilizer is a new product based on infrared sterilization technology.
The small size, light weight & its low energy consumption makes it uniquely suited for medical relief operations in the field.
This sterilizer uses the infrared technology to sterilizer medical instruments without corrosion damage to surfaces and sharp edges.
The instrument is portable and is easy to use.
The chamber size is 15"W X 18"L X 12"H.
Jindal Knife Sterilizers are widely used in the meat, fish and poultry industry for sterilizing butchers / boners knives. This unique product is operated by a 1.2kw 220v heating element; it has a water storage capacity of 2 litres in which it will heat to 83deg c which will kill all common bugs and bacteria which are common in the food industry.
The unit is insulated for maximum efficiency.
It has a hinged top cover so that condensation levels are minimised, the standard unit will hold 4 butchers knives concealed with top cover closed for sterilization to take place within 4 minutes.
The complete sterilizer is made of Stainless Steel. The temperature is controlled by a thermostat at the desired value.
We have designed this product to be fail safe. It consists of a low water level protection device which prevents the heater to burn out dry.
Optional Features:
JINDAL Fully Automatic Microprocessor based high pressure, high vacuum autoclave is designed to fulfill the needs of CS.S.D. unit & various other microbiology works. The sterilizer is designed for sterilizing hospital materials including agars, sterilization of solutions in open & closed bottles, disinfection of materials and waste decontamination.
Construction
The complete autoclave including the outer casing is made of High-grade stainless steel. The autoclave chamber is a horizontal model, rectangular in shape with front-loading design. The chamber & jacket are made of SS 316L. The chamber consists of rounded corners to prevent formation of debris & ensure efficient cleaning. The jacket is duly insulated with 50mm thick glass wool insulation to ensure low thermal losses.
The sterilizer is provided complete with high quality stainless steel trolleys and sterilization baskets.
External Trolley: 01
Internal trolley with steel roller & shelves: 01
Sterilization baskets: 02
The door is also made of SS 316L & is duly insulated with 50mm thick glass wool insulation to ensure that the working temperature of door is 420C. The fully automatic single vertical sliding door provides quick operation pass through system with latest multiple safety arrangements. Electrically operated door is linked to a silicone seal to provide perfect seal.
Fully Automatic Microprocessor Control:
The complete autoclave is linked to a microprocessor controller that monitors all the parameters in real time. The microprocessor control is linked to a bright color touch screen HMI to display & set all the parameters. The menu consists of 8 pre programmed standard cycles, which the operator can run at a touch of a button. Separate five user programmable cycles are also provided. The operator can edit & run any of these five cycles. Built in provision of chip card port for loading new programs through chip cards.
The operator access levels are programmable with password entry as under:
The built in alarm system provides message on the touch screen in case any failure or malfunction. The temperature is adjustable from 1210C up to 1350C. The safe working pressure range provided is 15 to 32PSIG. Routine calibration & maintenance checks are carried out on quarterly basis.
Safety & Ergonomic Features:
