Our Products
Wind Instruments
2 Products availableCarbide Cutting Tools
1 Products availableWe are leaders in the market for providing best range of Rougher Mill, Chamfer Drill Mill, SINGLE LIP Endmill Flute Standard Uncoated and Tapper Neck Ball Nose
Corner Radius Endmill improve productivity and reduce costs. A sharp corner of an end mill is its weakest point. The corner radius design strengthens the end mill by reducing chipping and providing longer tool life. In mold applications where ball end mills have traditionally been used, a corner radius end mill will remove more material faster, improving productivity. Saves the cost of grinding a radius using conventional end mills.
Item Code | Cutting Dia. | Shank Dia. | Radius | Flute length | Over all length |
---|---|---|---|---|---|
SF4CR030 R0.5 | 3 | 3 | 0.5 | 10 | 51 |
SF4CR040 R0.5 | 4 | 4 | 0.5 | 14 | 51 |
SF4CR040 R1.0 | 4 | 4 | 1 | 14 | 51 |
SF4CR050 R0.5 | 5 | 5 | 0.5 | 16 | 51 |
SF4CR050 R1.0 | 5 | 5 | 1 | 16 | 51 |
SF4CR060 R0.5 | 6 | 6 | 0.5 | 19 | 63 |
SF4CR060 R1.0 | 6 | 6 | 1 | 19 | 63 |
SF4CR060 R1.5 | 6 | 6 | 1.5 | 19 | 63 |
SF4CR080 R0.5 | 8 | 8 | 0.5 | 21 | 63 |
SF4CR080 R1.0 | 8 | 8 | 1 | 21 | 63 |
SF4CR080 R1.5 | 8 | 8 | 1.5 | 21 | 63 |
SF4CR080 R2.0 | 8 | 8 | 2 | 21 | 63 |
SF4CR100 R0.5 | 10 | 10 | 0.5 | 25 | 70 |
SF4CR100 R1.0 | 10 | 10 | 1 | 25 | 70 |
SF4CR100 R1.5 | 10 | 10 | 1.5 | 25 | 70 |
SF4CR100 R2.0 | 10 | 10 | 2 | 25 | 70 |
SF4CR100 R2.5 | 10 | 10 | 2.5 | 25 | 70 |
SF4CR120 R1.0 | 12 | 12 | 1 | 25 | 75 |
SF4CR120 R1.5 | 12 | 12 | 1.5 | 25 | 75 |
SF4CR120 R2.0 | 12 | 12 | 2 | 25 | 75 |
SF4CR120 R3.0 | 12 | 12 | 3 | 25 | 75 |
SF4CR160 R1.0 | 16 | 16 | 1 | 35 | 89 |
SF4CR160 R2.0 | 16 | 16 | 2 | 35 | 89 |
SF4CR160 R3.0 | 16 | 16 | 3 | 35 | 89 |
SF4CR160 R4.0 | 16 | 16 | 4 | 35 | 89 |
SF4CR200 R1.0 | 20 | 20 | 1 | 40 | 101 |
SF4CR200 R2.0 | 20 | 20 | 2 | 40 | 101 |
SF4CR200 R3.0 | 20 | 20 | 3 | 40 | 101 |
SF4CR200 R4.0 | 20 | 20 | 4 | 40 | 101 |
Item Code | Cutting Dia. | Shank Dia. | Flute length | Over all length |
---|---|---|---|---|
SF6EM060 | 6 | 6 | 19 | 63 |
SF6EM080 | 8 | 8 | 21 | 63 |
SF6EM100 | 10 | 10 | 22 | 70 |
SF6EM120 | 12 | 12 | 25 | 75 |
SF6EM140 | 14 | 14 | 30 | 76 |
SF6EM160 | 16 | 16 | 32 | 76 |
SF6EM180 | 18 | 18 | 35 | 100 |
SF6EM200 | 20 | 20 | 40 | 100 |
A reamer is a type of finishing tool. When we drill holes in lumps of metal, we typically use a fairly standard drill bit in either our mini-lathe or micro-mill. Drill bits do a pretty good job. If you only need a hole to pass a bolt through, or to tap with a thread, then a standard drill bit will create a suitable hole. A reamer will take a rough hole cut by a drill bit and turn it into a truely round hole of a known inner diameter.
Item Code | Cutting Dia. | Shank Dia. | Flute length | Over all length |
---|---|---|---|---|
SF4RM030 | 3 | 6 | 15 | 60 |
SF4RM040 | 4 | 6 | 18 | 60 |
SF4RM050 | 5 | 6 | 20 | 60 |
SF6RM060 | 6 | 6 | 25 | 75 |
SF6RM080 | 8 | 8 | 30 | 76 |
SF6RM100 | 10 | 10 | 35 | 100 |
SF6RM120 | 12 | 12 | 40 | 100 |
Rougher End Mills quickly remove large amounts of material. This kind of end mill utilizes a wavy tooth form cut on the periphery. These wavy teeth form many successive cutting edges producing many small chips, resulting in a relatively rough surface finish. During cutting, multiple teeth are in contact with the workpiece reducing chatter and vibration.
Item Code | Cutting Dia. | Shank Dia. | Flute length | Over all length |
---|---|---|---|---|
SF4RE050S | 5 | 5 | 16 | 51 |
SF4RE060S | 6 | 6 | 19 | 63 |
SF4RE080S | 8 | 8 | 21 | 63 |
SF4RE100S | 10 | 10 | 25 | 70 |
SF4RE120S | 12 | 12 | 25 | 75 |
SF4RE140S | 14 | 14 | 30 | 89 |
SF4RE160S | 16 | 16 | 32 | 89 |
SF4RE180S | 18 | 18 | 40 | 101 |
SF4RE200S | 20 | 20 | 40 | 101 |
A large number of all holes produced need a chamfer or at least some deburring. Some typical examples are screw and rivet holes. There are a number of drills to choose from and, by using circular interpolation, even a turning or a milling tool can be used.
Single Lip Endmill is necessary as it halves the neccessary feedrates without rubbing. So there is one case where it helps, when the machine just can't feed fast enough to keep up with what the spindle is putting out and maintain adequate chiploads.
Item Code | Cutting Dia. | Shank Dia. | Radius | Flute Length | Over All Length |
---|---|---|---|---|---|
SF1EM060R0.5 | 6 | 6 | 0.5 | 10 | 63 |
SF1EM080R0.5 | 8 | 8 | 0.5 | 12 | 63 |
SF1EM100R1.0 | 10 | 10 | 1 | 15 | 70 |
SF1EM120R1.0 | 12 | 12 | 1 | 20 | 75 |
SF1EM140R1.0 | 14 | 14 | 1 | 20 | 76 |
SF1EM160R1.0 | 16 | 16 | 1 | 25 | 76 |
SF1EM200R1.0 | 20 | 20 | 1 | 25 | 100 |