Our Products
Measuring Instruments & Equipment
2 Products availableIndustrial Pump
2 Products availableLubrication Systems And Equipment
2 Products availablePumps, Pumping Machines & Parts
1 Products availablePipe Tees
1 Products availableConveyors
1 Products availableElectric Fittings And Components
1 Products availableOur product range contains a wide range of centralised lubrication systems, Oil Mist Lubrication, Air-Oil Lubrication System and Lubomatic Centralised Dualline Lubrication System
In this system minimum quantity of oil is pushed by air in a narrow spiral tube and the tube is connected to the part of machine to be lubricated. The component of the machine / bearing is continuously supplied with droplet of oil. The air caries the oil droplet to the bearings & very small quantity of oil is supplied to bearings by using Lubomatic air-oil lubrication system the quantity of oil is precisely controlled. By using Lubomatic Air-Oil Lubrication system the machine can be operated at higher speed and productivity can be increased. The dust & dirt near by the bearings is forced away from the bearings and the bearing is kept clean & cool and lubricated.
The air oil Lubrication is used in
ADVANTAGES
SKEY PRODUTSmanufacturesLUBOMATICrange of centralised Lubrication SystemFor Sugar Mill bearings .The System consists of following components :-
| PUMP | A very highly reliable pump with high discharge pressure is incorporated in the system. The pump is reciprocating plunger type pump, which is keptimmersed in Oil . This pump is driven by a geared motor . Considering the continuous Opration of system all the components are manufactured to veryclose tolerance & a special grade material is used to ensure consistent performance . The working principal of the pump is very simple and performsnon-stop with very high delivery pressure. A standby pump is also provided. |
| MOTOR | A continuous duty electric geared motor with service factor of 2.9 is used. The motor used is a TEFC squirrel cage induction motor suitable for 415VAC, 3Phase, 50Hz, AC supply as per IS 325 with class B insulation .It is a geared motor with 125 RPM & 0.55 kw rating . |
| RESERVOIR | The pump driven by geared motor is kept immersed in oil to ensure long life & efficient working . The reservoir is of 50 lit . Capacity which is mounted on a pump housing . A level switch fitted to indicate low oil level in tank. Two oil level gauges are located on the front side of reservoir to check the oil level visually. |
| CHANGE OVER VALVES | The valve is hydraulically/electrically operated when the pump is switched ON the line1is connected and the pressure goes on increasing and when it reaches set high pressure all the points are lubricated as the valve moves forward the line gets blocked and the pressure goes on increasing and line changes to no.2line this goes on repeating. The dwell time is adjusted as per requirement and after set dwell time the cycle goes on repeating. |
| CONTROL PANEL | Two electric control panels which consists of Main Power Supply, Contactor, MCB etc., It ensure the smooth working of the system. In case of any faults thealarm is provided with visual indications. The selection of system 1 & System 2 ( Stand by Pump ) can be done using selector switch provided. |
| PRESSURE SWITCH | When the line pressure drops down the set pressure. The pressure switch gives signal to control panel & alarm is indicated on the panel & hooter switched ON |
| RELIEFVALVE | A relief valve is provide to safeguard the pump from overloading. By adjusting the relief valve setting the delivery pressure can be increased and decreased. |
| PIPING & FITTINGS | High quality seamless pipes are used to work under high pressures
Fittings of high quality standards are used to ensure leakage free consistent Working of the system. Various hydraulic fittings are used, such as male studElbow, Unequal Tee, Pipe Connector, Straight Connectors. Flexible Polyhoses are used wherever required. |
LUBOMATIC Centralised dual line lubrication system basically consists of a reservoir with built in reciprocating plunger pump immersed in the oil, change over valve, dose feeders ( Dual line metering elements ) Pressure Switch, pipes, hose pipes, fittings Electrical Control Panel etc.
In this type of system, there are two main lines of 16 OD, which run parallel to the Sugar Crushing Mill Tandem. From these two main lines, 10 OD Pipes are connected to inlet of dose feeders & the outlet of the dose feeders are connected to the lubrication points ( bearings ).
The valve is hydraulically / electrically operated when the pump is switched ON the line1is connected and the pressure goes on increasing and when it reaches set high pressure all the points are lubricated as the valve moves forward the line gets blocked and the pressure goes on increasing and line changes to no.2line this goes on repeating. The dwell time is adjusted as per requirement and after set dwell time the cycle goes on repeating.
The discharge of oil can be controlled by
The electric control panel monitors the smooth working of the system. The following step should be followed while operating the system.
| Reservoir ILow | Oil level in reservoirIis below required level. |
| Reservoir IILow | Oil level in reservoirIIis below required level. |
| Low Pressure ILow | If the pressure does not get developed in main line the panel will give this fault indication. |
| Low Pressure IILow | If the pressure does not get developed in main line the panel will give this fault indication. |
