Mumbai, Maharashtra, India
Our Products
A pressure transmitter is a measuring device which converts an applied pressure into an electrical signal. Generally, a pressure transducer consists of two parts, an elastic material which deforms under the application of pressure and an electrical part which detects this deformation.
Silent Features
Full automatic microprocessor based sequencing of 3 cylinder banks connected to dispenser through independent high pressure Stainless Steel (SS) tubes. Dispenser to have pressure control device to restrict fill pressure to 200 barg at maximum allowable filling pressure for natural gas vehicle cylinder. Pressure control device to ensure complete shut off of gas flow at the pre-set pressure with dead band shift and shut off error within 2% of range. The pre-set fill pressure can vary from 150 barg to 250 barg. The pressure control device have provision to manually set pressure between above range.
General construction & Assembly: All component used in compressed natural gas dispensing equipment is listed by a nationally recognized certification agency as complying with an applicable standard, or evaluated by the certification agency for the intended application as part of the dispensing equipment.
| Outlet pressure | 200 barg. Provision for PT adjustment of discharge pressure at 200 to 220 barg. |
| Overfill protection | Over fill protection through electronically programmed, in order to terminate fill above 200 bar G. 2 Nos. transducers per hose and pressure relief valve shall be provided |
| Inlet connection | 3 nos.½” O.D or higher size tube fittings. Full bore isolation SS ball valves is provided on the inlet of all 3 bank supply lines. Make of the valve shall be Parker / Swagelok or equivalent |
| Inlet filters | Coalescent filter of 3 microns to be provided at the inlet of each bank supply line with manual drain valve |
| Outlet connection | 2 nos. each with 4 metre long 3/8” ID CNG flexible electrically conductive twin (fill + vent) hose with 3 way valve. Size of vent hose is of ¼” ID. Both arms shall be of NZS type refuelling probe. Probe shall be as per NZS 5425 (latest edition) and compatible with NZS type refuelling valves (NZS 5422).The hoses shall be suitable for 5000 psig working pressure for CNG application.The delivery hose and vent hose shall be provided with a breakaway coupling |
| Breakaway coupling | Probe hose have proper hose guard and hoseguard is electrically nonconductive.3 way valve 10000 PSIG is ofapproved make. |
| Emergency manual shut off valve | 1 no. on each line |
| Flow rate per hose | Dispensers is designed for handling flow rate not less than 15 Kg/min for each arm |
| Metering principle | Coriolis |
| Mass flow meter make | Micromotion [CNG 50, model no for sensor CNG 050 and model no for transmitter 1700 or higher (latest version)] or Endress + Hauser (Model no CNG PROMASS, DN 15 with head mounted display/KG80). HART output is available for communication with HART. Mass flow meter sensor and transmitter is Type approval from legal metrology department. |
| Pressure gauges | 1 no liquid filled 4” dia. (0-400 Bar) pressure gauges with SS casing to indicate vehicle filling pressure.Pressure gauge shall be provided with shatter proof glass |
| Sequencing | Sequencing shall be automatic and controlled by the microprocessor / PLC. Three sequencing valves per hose outlet (total of 6 valves per dual hose dispenser) and in addition to this there is one main actuator valve per hose (after mass flow meter). Sequencing valves shall be operated by pneumatic air |
| Dispenser Electronics | The dispenser electronics is PLC / microprocessor/ Modbus protocol based and suitable for extreme climatic conditions. The processor/ PLC is of latest version / latest configuration available in the field. The baud rate/ SCAN time of the processor is minimum as per the latest available. All the electronics cards is located in flameproof junction boxes inside the dispenser cabinet and the cable entry to the junction boxes is from bottom |
| Display | Three rows Trans-reflective Liquid Crystal Display, Capable of withstanding temperature ranging from - 20°C to +65°C. There is 2 displays/hose, one on each sides of the dispenser (total 4 sets of 3 rows displays for each Dual hose dispenser. Internal back-up power supply for displays so that displays remains for at least 5 minutes after power failure. |
| Totaliser | Dispenser have electronic digital non-volatile, non-resettabletotaliser for accurate accounting and 8 digits before decimal point for total CNG sold in kgs. which have an independent battery backup |
| Accuracy | The batch accuracy of dispensed gas is within + 0.6% |
| Area classification | Hazardous area Class I Div I Group D as per NES or Zone I Group IIA / IIB as per IS/ IEC |
| Breakaway coupling Delivery hose is provided with breakaway coupling OPW (model FLB1000)/WEH/Staublietc. Vent hose is also provided with breakaway coupling OPW (Model VLB)/WEH/Staublietc | |
| Certification | Certificationfrom Weights and Measures department of India for the dispenser /mass flow meter. IP 55 approval for dispenser cabinet |
| Water cooled exhaust Manifold. |
| Naturally aspirated / Turbo charged Intercooled design. |
| Water cooled Turbo charger exhaust housing. |
| Engine driven Radiator fan and radiator assembly. |
| Auxiliary water cooling system. |
| Approved ignition system. |
| Electronic air fuel ratio controller/ Electronic gas carburetor |
| Electronic / Mechanical governing system. |
| Inline / V type configuration. |
| Six / Eight cylinder configuration. |
| Air starting system. |
|
Designed for heavy shop or industrial use, Electric-driven Single stage &Two-stage air compressors are made of heavy-duty components to give optimum performance. These compressors have two different sized cylinder bores. Robust design crankshaft for reliability and easy maintenance, solid end connecting rods, high thermal efficiency, inter-cooling, totally reliable splash lubrication and balanced V-type construction for smooth & vibration-free operation.
Silent Features:
|
| S/N | MODEL | FLOW | END CONN | CONN TYPE | OVERALL DIAMENSIONS IN MM | WT.KGS(APPX) | |||
|---|---|---|---|---|---|---|---|---|---|
| Nm/Hr | SCFM | Depth | Width | Height | |||||
| 1 | HD V | 9 | 5 | 1/4" | 1/4"BSP SC.F | 150 | 550 | 670 | 35 |
| 2 | HD V1 | 17 | 10 | 1/2" | 1/2"BSP SC.F | 410 | 700 | 1050 | 50 |
| 3 | HD V2 | 25 | 15 | 1/2" | 1/2"BSP SC.F | 410 | 750 | 1280 | 70 |
| 4 | HD V3 | 34 | 20 | 1/2" | 1/2"BSP SC.F | 410 | 750 | 1670 | 90 |
| 5 | HD 001 | 50 | 30 | 1/2" | 1/2"BSP SC.F | 450 | 750 | 1850 | 120 |
| 6 | HD001 V | 80 | 45 | 3/4" | 3/4"BSP SC.F | 450 | 800 | 1680 | 150 |
| 7 | HD 002 | 100 | 60 | 3/4" | 3/4"BSP SC.F | 500 | 850 | 1780 | 170 |
| 8 | HD002 V | 130 | 75 | 3/4" | 3/4"BSP SC.F | 500 | 850 | 1960 | 198 |
| 9 | HD003 V | 170 | 100 | 1" | 1"BSP SC.F | 550 | 1000 | 2100 | 227 |
| 10 | HD004 V | 240 | 140 | 1 1/2" | FLGD.ASA 150 # | 550 | 1000 | 2100 | 274 |
| 11 | HD007 | 340 | 200 | 1 1/2" | FLGD.ASA 150 # | 600 | 1180 | 2230 | 350 |
| 12 | HD 009 V | 475 | 280 | 2" | FLGD.ASA 150 # | 600 | 1300 | 2300 | 498 |
| 13 | HD 012 V | 650 | 380 | 2" | FLGD.ASA 150 # | 1150 | 1450 | 1950 | 650 |
| 14 | HD0016 V | 850 | 500 | 2 1/2" | FLGD.ASA 150 # | 1275 | 1600 | 2350 | 790 |
| 15 | HD 020 V | 1050 | 620 | 3" | FLGD.ASA 150 # | 1380 | 1725 | 2480 | 925 |
| 16 | HD025 | 1290 | 760 | 3" | FLGD.ASA 150 # | 1530 | 1850 | 2250 | 1125 |
| 17 | HD 038 | 1940 | 1140 | 4" | FLGD.ASA 150 # | 1800 | 1690 | 2625 | |
| MODEL | AIR FLOW* | MAX OPERATING PRESSURE | POWER SUPPLY | VERSION*** | AIR CONNECTIONS | DIAMENSIONS (MM) | ||||
|---|---|---|---|---|---|---|---|---|---|---|
| m3/min | cfm | kg/cm2 | psi | V/ph//HZ | BSP(F) | LENGTH | WEIDTH | HEIGHT | ||
| S1OR | 0.28 | 10 | 16 | 228 | 230/1/50 | Air cooled | 1/2" BSP | 480 | 400 | 625 |
| S2OR | 0.57 | 20 | 16 | 228 | 230/1/50 | Air cooled | 1/2" BSP | 480 | 400 | 625 |
| S35R | 1.00 | 35 | 16 | 228 | 230/1/50 | Air cooled | 1/2" BSP | 480 | 400 | 625 |
| S50R | 1.40 | 50 | 16 | 228 | 230/1/50 | Air cooled | 3/4" BSP | 480 | 400 | 625 |
| S60R | 1.70 | 60 | 16 | 228 | 230/1/50 | Air cooled | 3/4" BSP | 480 | 400 | 625 |
| S80R | 2.27 | 80 | 16 | 228 | 230/1/50 | Air cooled | 1" BSP | 680 | 560 | 850 |
| S100R | 2.80 | 100 | 16 | 228 | 230/1/50 | Air cooled | 1" BSP | 680 | 560 | 850 |
| S125R | 3.50 | 125 | 16 | 228 | 230/1/50 | Air cooled | 1 1/2" BSP | 680 | 560 | 850 |
| S150R | 4.25 | 150 | 16 | 228 | 230/1/50 | Air cooled | 1 1/2" BSP | 680 | 560 | 850 |
| S200R | 5.66 | 200 | 16 | 228 | 230/1/50 | Air cooled | 1 1/2" BSP | 750 | 650 | 1000 |
| S250R | 7.07 | 250 | 16 | 228 | 230/1/50 | Air cooled | 1 1/2" BSP | 750 | 650 | 1000 |
| S350R | 9.90 | 350 | 16 | 228 | 230/1/50 | Air cooled | 2" FLANGED | 850 | 750 | 1150 |
| S450R | 12.75 | 450 | 16 | 228 | 230/1/50 | Air cooled | 2" FLANGED | 850 | 750 | 1150 |
| S550R | 15.57 | 550 | 16 | 228 | 415/3/50 | Air cooled | 2" FLANGED | 1000 | 850 | 1350 |
| S650R | 18.41 | 650 | 16 | 228 | 415/3/50 | Air cooled | 3" FLANGED | 1000 | 850 | 1350 |
| S750R | 21.24 | 750 | 16 | 228 | 415/3/50 | Air cooled | 3" FLANGED | 1000 | 850 | 1350 |
| S900R | 25.49 | 900 | 16 | 228 | 415/3/50 | Air cooled | 3" FLANGED | 1100 | 950 | 1500 |
| S11OOR | 31.15 | 1100 | 16 | 228 | 415/3/50 | Air cooled | 4" FLANGED | 1100 | 950 | 1500 |
A temperature transmitter is a device that connects to a temperature sensor to transmit the signal elsewhere for monitoring and control purposes. Typically, the temperature sensor is an RTD, Thermisor or Thermocouple type sensor and will interface with a PLC, DCS, data logger or display hardware. The temperature transmitter's role is to isolate the temperature signal, filter any EMC noise, amplify and convert the temperature sensor's signal to a 4-20mA or 0-10V DC range for further use.
Silent Features
A flow meter is a device used to measure the flow rate or quantity of a gas or liquid moving through a pipe. Flow measurement applications are very diverse and each situation has its own constraints and engineering requirements. You can measure flow through a variety of different devices such as Coriolis and positive displacement meters.
An electrical panel is also called a load center. It is a metal electrical service box that accepts the main power to the home/office/service area and distributes electrical current to the various circuits within the Home/office/ Service area. Also known as:Load Center, Service Panel, Breaker Panel, Fuse Box.The distribution of power to the various circuits is protected from over-current by the use of circuit breakers or fuses.
TheseElectrical Control Panels are widely used in different places such as Telecom sector, Oil & Gas sector, Power Sector and others as per the need of the clients. Our offered panels are available in various specifications in order to attain maximum clients' satisfaction. Moreover, these panels are delivered to the clients at reasonable rates.
Sicom Sales & Engineering is a team of qualified dedicated engineering professionals having a rich experience in the field of power electronics. The company firmly believes in delivering total customer satisfaction spanning from concept todesign, commissioning to after sales service.
We offers fully engineered & cost effective solutions for process Automation & controls , integrating Digital DC Drives, PLC with networking & interfacing with process computers/ HMis.
|
