Our Products
Strong Magnetic Field to hold the work piece strongly. Used for holding on surface grinding machine. This chuck is tested for earth terminal test, waterproof test, temperature rise test, & demagnetizing tests. Provided with variable supply to vary power, which helps in aligning & removing of warp ages of thin jobs. Work holding device for surface grinding machines, each pole is having separate coil, as such very strong & even magnetic flux is generated.
Strong Magnetic Field to hold the work piece strongly.
Used for holding on surface grinding machine.
Chuck is tested for earth terminal test, waterproof test, temperature rise test, & demagnetizing tests.
Provided with variable supply to vary power, which helps in aligning & removing of warp ages of thin jobs.
Work holding device for surface grinding machines, each pole is having separate coil, as such very strong& even magnetic flux is generated.
Cat No. Sizes mm. Pole
L W H Gap Pitch
SI-EMC-1806 MP 450 x 150 x 100 15 40
SI-EMC-2008 MP 500 x 200 x 100 15 40
SI-EMC-2408 MP 600 x 200 x 100 15 40
SI-EMC-2410 MP 600 x 250 x 100 15 40
SI-EMC-3010 MP 750 x 250 x 100 15 40
SI-EMC-3610 MP 900 x 250 x 100 15 40
SI-EMC-2412 MP 600 x 300 x 100 15 40
SI-EMC-3012 MP 750 x 300 x 100 15 40
SI-EMC-3612 MP 900 x 300 x 100 15 40
SI-EMC-4010 MP 1000 x 250 x 110 15 40
SI-EMC-4012 MP 1000 x 300 x 110 15 40
SI-EMC-6010 MP 1500 x 250 x 110 15 40
SI-EMC-6012 MP 1500 x 300 x 110 15 40
SI-EMC-6016 MP 1500 x 400 x 110 15 40
These Electromagnetic Chucks are designed for strong electro magnetic field to hold the work piece securelyMinimum mechanical deformation with solid one -piece housing Uniform magnetic force distribution with specially developed rigid top plateMinimum power consumptionFull magnetic surface offering easy operationVersatile clamping, excellent holding on a broad range of work piece sizesPossibility to combine several chucks for a large uninterrupted surfaceLow profile for more wheel head clearance Normal input voltage 110 VDC.Back and end work stop railMinimum twice the length of chuck power cable
control unit
D.C.POWER SUPPLY UNIT WITH MAG / DEMAG FACILITY
VARIABLE CONTROL UNIT
NORMAL INPUT VOLTAGE 230 SINGLE PHASE.
SPECIAL SIZES ARE AVAIBLE ON REQUEST.
SPECIFICATIONS:
Cat No. Sizes mm. Pole Gap mm
L W H
SH - ELM - 1460 FP 350 X 150 X 100 4 + 1
SH - ELM - 1860 FP 450 X 150 X 100 4 + 1
SH - ELM - 2080 FP 500 X 200 X 100 4 + 1
SH - ELM - 2480 FP 600 X 200 X 100 4 + 1
SH - ELM - 2410 FP 600 X 250 X 100 4 + 1
SH - ELM - 2412 FP 600 X 300 X 100 4 + 1
SH - ELM - 3010 FP 750 X 250 X 100 4 + 1
SH - ELM - 3012 FP 750 X 300 X 100 4 + 1
SH - ELM - 3610 FP 900 X 250 X 100 4 + 1
SH - ELM - 3612 FP 900 X 300 X 100 4 + 1
SH - ELM - 4010 FP 1000 X 250 X 110 4 + 1
SH - ELM - 4012 FP 1000 X 300 X 110 4 + 1
SH - ELM - 6010 FP 1500 X 250 X 110 4 + 1
SH - ELM - 6012 FP 1500 X 300 X 110 4 + 1
SH - ELM - 6016 FP 1500 X 400 X 110 4 + 1
"KUMAUN" introduces Electro-perm Magnetic Chucks for heavy duty milling machine. These chucks ensure high magnetic and mechanical performance. The chuck is "COLD" device, as no internal wear or deformation resulting from moving internal parts. Electro-perm Magnetic Chucks do not consume electrical power except for the very short period of activation or deactivation of the working surface. Once fixed to the machine table EPM chucks are as stable as machines. EPM chucks are economical for operation and maintenance. Magnetic clamping system is most powerful. Chucks are switched ON & OFF by simple electrical pulse. A variable output from 20% to 100 % is controlled from push button unit.
In operating condition no power supply is necessary for holding work pieces. So no risk when power fails. The de-magnetization cycle of the chuck eliminates possible residual magnetism in work piece, therefore easy release for high alloy steel parts. EPM chuck is designed for heavy-duty operation such as milling cut of 3 to 6 mm depth at recommended speed & feed.
Electro-perm magnetic chuck offers minimum mechanical deformation with solid one piece housing. This chuck is a COLD device. These chucks do not consume electrical power except when activation and deactivation of magnets power is required. This results in very less consumption of electricity as compared to conventional electrical chucks. EPM chucks are economical for operation and maintenance and also most powerful chucks. These chucks are switched ON and OFF with simple electrical pulse. A variable output from 20% to 100% is controlled from one push button switch. EPM chucks are entirely independent of external power supply during the holding of work pieces. So no risk when power fails. The demagnetization cycle of EPM chucks reduces possible residual magnetism in the work piece.
This permanent magnetic chuck guarantees outstanding performance and reliability. The rigid assembly of these chucks result in accurate grinding and milling. The selected pole spacing ensures the maximum possible grip on a wide section of work-pieces. Using an additional top plate can accommodate all types, sizes and shapes of workpieces. The magnet used is ‘NdFeB’. This magnet is very powerful than ‘AlNiCo’ magnet. Under ideal conditions the test result show that the holding power/Cu.Inch is 55Kg., which is much bigger than ‘AlNiCo’ magnetic chuck.
Coil type demagnetizer is designed to operate on alternative current to demagnetize a work-piece. Just pass through the coil and remove it from the field of the demagnetizer. Care should be taken to assure that the work-piece kept is well away from the demagnetizer before the magnetizer is switched OFF. This KUMAUN type demagnetizer is very useful for rods, bars, small jobs, etc.
Size :
This permanent magnetic chuck guarantees outstanding performance and reliability. The rigid assembly of these chucks result in accurate grinding and milling. The selected pole spacing ensures the maximum possible grip on a wide section of work-pieces. Using an additional top plate can accommodate all types, sizes and shapes of work-pieces. The magnet used is NdFeB. This magnet is very powerful than AlNiCo magnet. Under ideal conditions the test result show that the holding power/Cu.Inch is 55Kg., which is much bigger than AlNiCo magnetic chuck.
SPECIFICATIONS:
Cat No. Sizes inch. Pole Gap mm
SI - Neo - 1260 SP 300 X 150 X 65 19
SI - Neo - 1460 SP 350 X 150 X 65 19
SI - Neo - 1860 SP 450 X 200 X 70 19
SI - Neo - 1880 SP 450 X 200 X 70 19
SI - Neo - 2080 SP 500 X 200 X 70 19
SI - Neo - 2480 SP 600 X 200 X 70 19
SI - Neo - 2410 SP 600 X 250 X 70 19
SI - Neo - 2412 SP 600 X 300 X 70 19
Cat No. Sizes inch. Pole Gap mm
SI - Neo - 1260 MP 300 X 150 X 65 14
SI - Neo - 1460 MP 350 X 150 X 65 14
SI - Neo - 1860 MP 450 X 200 X 70 14
SI - Neo - 1880 MP 450 X 200 X 70 14
SI - Neo - 2080 MP 500 X 200 X 70 14
SI - Neo - 2480 MP 600 X 200 X 70 14
SI - Neo - 2410 MP 600 X 250 X 70 14
SI - Neo - 2412 MP 600 X 300 X 70 14
Cat No. Sizes inch. Pole Gap mm
SI - Neo - 1260 CP 300 X 150 X 65 12
SI - Neo - 1460 CP 350 X 150 X 65 12
SI - Neo - 1860 CP 450 X 200 X 70 12
SI - Neo - 1880 CP 450 X 200 X 70 12
SI - Neo - 2080 CP 500 X 200 X 70 12
SI - Neo - 2480 CP 600 X 200 X 70 12
SI - Neo - 2410 CP 600 X 250 X 70 12
SI - Neo - 2412 CP 600 X 300 X 70 12
These chucks do not consume electrical power only when activation and deactivation of magnets power is required. This results in very less consumption of electricity as compared to conventional electrical chucks.
EPM chucks are economical for operation and maintenance and also most powerful chucks. These chucks are switchedONandOFFwith simple electrical pulse. A variable output from 20% to 100% is controlled from one push button switch.EPM chucks are entirely independent of external power supply during the holding of work pieces. So no risk when power fails.
The demagnetization cycle of EPM chucks reduces possible residual magnetism in the work piece.
SPECIFICATIONS:
Cat No. Sizes mm. Pole Gap mm
L W H
SH - EPM - 1460 350 X 150 X 70 4 + 1
SH - EPM - 1860 450 X 150 X 70 4 + 1
SH - EPM - 2080 500 X 200 X 70 4 + 1
SH - EPM - 2480 600 X 200 X 70 4 + 1
SH - EPM - 2410 600 X 250 X 70 4 + 1
SH - EPM - 2412 600 X 300 X 70 4 + 1
SH - EPM - 3010 750 X 250 X 70 4 + 1
SH - EPM - 3012 750 X 300 X 70 4 + 1
SH - EPM - 3610 900 X 250 X 70 4 + 1
SH - EPM - 3612 900 X 300 X 70 4 + 1
SH - EPM - 4010 1000 X 250 X 70 4 + 1
SH - EPM - 4012 1000 X 300 X 70 4 + 1
SH - EPM - 6010 1500 X 250 X 70 4 + 1
SH - EPM - 6012 1500 X 300 X 70 4 + 1
SH - EPM - 6016 1500 X 400 X 70 4 + 1
This permanent magnetic chuck guarantees outstanding performance and reliability. The rigid assembly of these chucks result in accurate grinding and milling.
The selected pole spacing ensures the maximum possible grip on a wide section of work-pieces. Using an additional top plate can accommodate all types, sizes and shapes of work-pieces. The magnet used is NdFeB. This magnet is very powerful than AlNiCo magnet.
Under ideal conditions the test result show that the holding power/Cu.Inch is 55Kg., which is much bigger than AlNiCo magnetic chuck.
Coil type demagnetizer is designed to operate on alternative current to demagnetize a work-piece. Just pass through the coil and remove it from the field of the demagnetizer. Care should be taken to assure that work-piece is well away from the demagnetizer before the magnetizer is switched OFF. KUMAUN type demagnetizer is very useful for rods, bars, small jobs, etc.
Strong Magnetic Field to hold the work piece strongly.
Used for holding on surface grinding machine.
Chuck is tested for earth terminal test, waterproof test, temperature rise test, & demagnetizing tests.
Provided with variable supply to vary power, which helps in aligning & removing of warp ages of thin jobs.
Work holding device for surface grinding machines, each pole is having separate coil, as such very strong & even magnetic flux is generated.
' KUMAUN ' Introduces the Permanent Magnetic Chuck guarantees outstanding performance and reliability. The rigid assembly of these chucks result in accurate grinding or light milling work. The carefully selected pole spacing ensures the maximum possible grip on a wide section of work pieces. Using an additional top plate can accommodate all types, sizes and shapes of work pieces. The magnetic used in these chucks are "NdFeB" type. This magnet is very powerful than "AlNiCo" type. Under ideal conditions the test result shows that the holding power/cu. inch is 55 kg. Which is much higher than "AlNiCo" magnets
than "AlNiCo" magnets.
Accuracy as per IS - 4816 - 1971
SPECIFICATIONS:
Cat No. Size mm. Pole Gap mm
KM - 100 SP D100 X H60 19
KM - 150 SP D150 X H60 19
KM - 160 SP D160 X H60 19
KM - 200 SP D200 X H60 19
KM - 225 SP D225 X H60 19
KM - 250 SP D250 X H70 19
KM - 315 SP D315 X H80 19
KM - 375 SP D375 X H80 19
KM - 400 SP D400 X H80 19
KM - 450 SP D450 X H80 19
Cat No. Size mm. Pole Gap mm
KM - 100 MP D100 X H60 14
KM - 150 MP D150 X H60 14
KM - 160 MP D160 X H60 14
KM - 200 MP D200 X H60 14
KM - 225 MP D225 X H60 14
KM - 250 MP D250 X H70 14
KM - 315 MP D315 X H80 14
KM - 375 MP D375 X H80 14
KM - 400 MP D400 X H80 14
KM - 450 MP D450 X H80 14
"KUMAUN" introduces Electro-perm Magnetic Chucks for heavy duty milling machine. These chucks ensure high magnetic and mechanical performance. This chuck is "COLD" device, as no internal wear or deformation resulting from moving internal parts.
Electro-perm Magnetic Chucks do not consume electrical power except for the very short period of activation or deactivation of the working surface. Once fixed to the machine table EPM chucks are as stable as machine.
EPM chucks are economical for operation and maintenance. Magnetic
clamping system is most powerful. Chucks are switched ON & OFF by simple electrical pulse. A variable output from 20% to 100 % is controlled from push button unit.
In operating condition no power supply is necessary for holding work pieces. So no risk when power fails.
The de-magnetization cycle of chuck eliminates possible residual magnetism in work piece, therefore easy release for high alloy steel parts. EPM chuck is designed for heavy-duty operation such as milling cut of 3 to 6 mm depth at recommended speed & feed.