FEATURES & SPECIFICATION

• Can be solid or perforated
• Manufactured by M-30 grade of concrete by vibro compaction process using joint less FRP moulds so as to achieve shuttering finish.
• Perforated saucer drains are reinforced, while the plain ones can be reinforced on request

FEATURES & SPECIFICATION

• Covers are provided with hot dip galvanized lifting hooks
• Test Load as per (IS-12592 Part 1) for Extra Heavy Duty is 35 MT, Heavy Duty is 20 MT, Medium Duty is 10 MT, and Light Duty is 2.5MT
• Covers can also be provided with holes for stormwater drainage
• Note: Covers of nonstandard sizes can also be supplied
• Concrete grade of M-30 or higher is used

FEATURES & SPECIFICATION

• Covers are provided with hot dip galvanized lifting hooks
• Test Load as per (IS-12592 Part 1) for Extra Heavy Duty is 35 MT, Heavy Duty is 20 MT, Medium Duty is 10 MT, and Light Duty is 2.5MT
• Covers can also be provided with holes for storm water drainage
• Note: Covers of non standard sizes can also be supplied
• Concrete grade of M-30 or higher is used

FEATURES & SPECIFICATION

• Covers are provided with hot dip galvanized lifting hooks
• Test Load as per (IS-12592 Part 1) for Extra Heavy Duty is 35 MT, Heavy Duty is 20 MT, Medium Duty is 10 MT, and Light Duty is 2.5MT
• Covers can also be provided with holes for storm water drainage
• Note: Covers of non standard sizes can also be supplied
• Concrete grade of M-30 or higher is used

FEATURES & SPECIFICATION

• Manufactured with M - 30 grade of concrete by vibro compaction process
• Suitably reinforced for handling and to withstand light to extra heavy duty loads
• Provided with a tongue and groove joint to create a water tight joint between adjacent units (it is recommended to fill the groove with cement mortar)
• The drain should be installed on a properly compacted base

FEATURES & SPECIFICATION

• Precast concrete wall caps (or coping) can be placed on any wall to add protection and beauty. Several standard colours and finishes (e.g., terazzo) are available.
• When deciding what size of wall cap to use, calculate the width measurement by measuring the width of the wall and adding at least 3/4" on each side for overhang. An overhang will allow the water to drip off of the edge and protect the wall beneath. For example, an 8" wall would need at least a 9 5/8" wide coping.
• Overall Dimensions: 300 mm (Width) X 600 mm (Length) X 40/50 mm (Thickness)
• Manufactured by using M-30 grade of concrete by vibro compaction process using jointless moulds so as to get shuttering finish .

FEATURES & SPECIFICATION

• Overall Dimensions: 2000 mm Length X 800 mm Height X 600 mm Bottom Width Inverted V Shape cross-section
• Manufactured by M-30 grade of concrete using vibro-compaction process
• Reinforced with 8 mm dia. Tor steel at 150mm centre to centre both ways

FEATURES & SPECIFICATION

• Overall Dimensions: 3045 mm Length X 840 mm Height X 610 mm Bottom Width
• Manufactured by M-30 grade of concrete using vibro-compaction process
• Reinforced with 16 mm dia. Tor steel at 150mm centre to centre both ways.
• Provided with two number hooks at both ends.

FEATURES & SPECIFICATION

• Manufactured by using M-30 grade of concrete
• Manufactured by vibro compaction process
• Manufactured by using joint less FRP moulds, so at to achieve shuttering finish on five faces
• All below manufactured products are also available with 2mm thick glavanised iron sheet in various sizes.
• All dimension are in MM (Mili meter.)

FEATURES & SPECIFICATION

• Precast concrete wall caps (or coping) can be placed on any wall to add protection and beauty. Several standard colours and finishes (e.g., terazzo) are available.
• When deciding what size of wall cap to use, calculate the width measurement by measuring the width of the wall and adding at least 3/4" on each side for overhang. An overhang will allow the water to drip off of the edge and protect the wall beneath. For example, an 8" wall would need at least a 9 5/8" wide coping.
• Overall Dimensions: 425 mm (Width) X 425 mm (Length) X 50/90 mm (Thickness)
• Manufactured by using M-30 grade of concrete by vibro compaction process using jointless moulds so as to get shuttering finish .

FEATURES & SPECIFICATION

• Overall Dimensions:  300 mm (Width) X 600 mm (Length) X 75/100 mm (Thickness)
• Manufactured by using M-30 grade of concrete by vibro compaction process using jointless moulds so as to get shuttering finish.

FEATURES & SPECIFICATION

• Can be solid or perforated
• Manufactured by M-30 grade of concrete by vibro compaction process using joint less FRP moulds so as to achieve shuttering finish.
• Perforated saucer drains are reinforced, while the plain ones can be reinforced on request

FEATURES & SPECIFICATION

• Covers are provided with hot dip galvanized lifting hooks
• Test Load as per (IS-12592 Part 1) for Extra Heavy Duty is 35 MT, Heavy Duty is 20 MT, Medium Duty is 10 MT, and Light Duty is 2.5MT
• Covers can also be provided with holes for stormwater drainage
• Note: Covers of nonstandard sizes can also be supplied
• Concrete grade of M-30 or higher is used

FEATURES & SPECIFICATION

• Covers are provided with hot dip galvanized lifting hooks
• Test Load as per (IS-12592 Part 1) for Extra Heavy Duty is 35 MT, Heavy Duty is 20 MT, Medium Duty is 10 MT, and Light Duty is 2.5MT
• Covers can also be provided with holes for storm water drainage
• Note: Covers of non standard sizes can also be supplied
• Concrete grade of M-30 or higher is used

FEATURES & SPECIFICATION

• Covers are provided with hot dip galvanized lifting hooks
• Test Load as per (IS-12592 Part 1) for Extra Heavy Duty is 35 MT, Heavy Duty is 20 MT, Medium Duty is 10 MT, and Light Duty is 2.5MT
• Covers can also be provided with holes for storm water drainage
• Note: Covers of non standard sizes can also be supplied
• Concrete grade of M-30 or higher is used

FEATURES & SPECIFICATION

• Manufactured with M - 30 grade of concrete by vibro compaction process
• Suitably reinforced for handling and to withstand light to extra heavy duty loads
• Provided with a tongue and groove joint to create a water tight joint between adjacent units (it is recommended to fill the groove with cement mortar)
• The drain should be installed on a properly compacted base

FEATURES & SPECIFICATION

• Precast concrete wall caps (or coping) can be placed on any wall to add protection and beauty. Several standard colours and finishes (e.g., terazzo) are available.
• When deciding what size of wall cap to use, calculate the width measurement by measuring the width of the wall and adding at least 3/4" on each side for overhang. An overhang will allow the water to drip off of the edge and protect the wall beneath. For example, an 8" wall would need at least a 9 5/8" wide coping.
• Overall Dimensions: 300 mm (Width) X 600 mm (Length) X 40/50 mm (Thickness)
• Manufactured by using M-30 grade of concrete by vibro compaction process using jointless moulds so as to get shuttering finish .

FEATURES & SPECIFICATION

• Overall Dimensions: 2000 mm Length X 800 mm Height X 600 mm Bottom Width Inverted V Shape cross-section
• Manufactured by M-30 grade of concrete using vibro-compaction process
• Reinforced with 8 mm dia. Tor steel at 150mm centre to centre both ways

FEATURES & SPECIFICATION

• Overall Dimensions: 3045 mm Length X 840 mm Height X 610 mm Bottom Width
• Manufactured by M-30 grade of concrete using vibro-compaction process
• Reinforced with 16 mm dia. Tor steel at 150mm centre to centre both ways.
• Provided with two number hooks at both ends.

FEATURES & SPECIFICATION

• Manufactured by using M-30 grade of concrete
• Manufactured by vibro compaction process
• Manufactured by using joint less FRP moulds, so at to achieve shuttering finish on five faces
• All below manufactured products are also available with 2mm thick glavanised iron sheet in various sizes.
• All dimension are in MM (Mili meter.)

FEATURES & SPECIFICATION

• Precast concrete wall caps (or coping) can be placed on any wall to add protection and beauty. Several standard colours and finishes (e.g., terazzo) are available.
• When deciding what size of wall cap to use, calculate the width measurement by measuring the width of the wall and adding at least 3/4" on each side for overhang. An overhang will allow the water to drip off of the edge and protect the wall beneath. For example, an 8" wall would need at least a 9 5/8" wide coping.
• Overall Dimensions: 425 mm (Width) X 425 mm (Length) X 50/90 mm (Thickness)
• Manufactured by using M-30 grade of concrete by vibro compaction process using jointless moulds so as to get shuttering finish .

FEATURES & SPECIFICATION

• Overall Dimensions:  300 mm (Width) X 600 mm (Length) X 75/100 mm (Thickness)
• Manufactured by using M-30 grade of concrete by vibro compaction process using jointless moulds so as to get shuttering finish.