Product Description

• Design Structures : Aerodynamic, floor mounted
• Air Flow Type : Automatic bypass type
• Construction (Exteriors) : Available in two options:-
• Stainless Steel 304gr. Outside & 316gr. S.S.Inside.
• Epoxy power coated 18 & 22 Gauge Galvanized Steel
• Baffle arrangement : 2 Point suction section with baffle to ensure smooth And immediate exhaust of fumes. As per ASHRAE & EN norms.
• Airfoil : Flush powder coated airfoil mounted on the worktop.
• Worktop : Available in following options
• Chemical resistant splash & spiliage proof jet black Granite worktop. Sink, water tap with drain arrangement worktop fitted with oval shaped 100 x 200mm PP cup-sink for drainage.
• Epoxy top (at extra cost)
• Stainless Steel 316gr.
• Sash (Shutter) : Vertical Sliding Counter balanced toughened glass (5mm thick / Polycarbonate fitted in the powder coated Aluminum. Clear sash open height =500mm-675mm According to size & Fume Hood.
• Service Fittings : Remotely operated color coded ( as per international standard) total three services valves with SS breaded flexible hose & brass fittings (1 for water & 2 for gases).
• Lighting : CFL tube light (1x36W) with Polycarbonate enclosed for Better Illumination with less power concumption.
• Electrical utilitie : Four nos electrical sockets 15/5amp & switches, ‘North West / HAVELLS make 50Hz switches have LED to Indicators to show ON position of switches to be Provided. Control panel provided with starter for blower.
• Complete rigid structure to support fume hood.
• Double skin shutter with self closing hinges.
• Digital Air Flow : This device is an accessory for fume hood to indicate the Approximate face velocity of airflow with primary
• Purpose of warning when a low flow condition occurs. Red & LED’s correspond to low & normal flow rates. When flow decreases from normal to low an audible Alarm will also actuate requiring manual Acknowledgement for silence.
• Centrifugal Blowe : Silent high efficiency blower, consisting of continuous Rating motor and chemical resistant impeller. The blower Designed to give face velocity of 80 to 120 feet/minute (FPM) as per ANSI/AIHA Z9.5 at the safe working Height.
• Air suction capacity : Silent 650 CFM confirming to international face velocity Norms and a per fume hood airflow pattern. Fume Hood (Stainless Steel) Frame of S.S.304grade from outside & 316 grade inside.

BOD Incubator is designed for low temperature incubation and determination of Bio Chemical Oxygen Demand (B.O.D). The BOD Incubator comes with a double wall construction. The Inner chamber is made of richly anodized aluminum or highly polished stainless steel with with two / three removable perforated shelves. The exterior chamber of the BOD Incubator is made of thick mild steel sheet duly finished in enamel paint. Outer double wall door is provided with magnetic gasket and lock & key arrangement. The inner door is made out of clear acrylic sheet allowing inspection of material in the chamber without disturbing the chamber temperature. Door operated inner illumination has been provided. The gap between walls of equipment are filled with glass wool for temperature insulation. The cabinet is mounted on castors. The temperature in the BOD Incubator is controlled by a sensitive thermostat from 5oC to 50oC ± 1oC. For lower temperature working, a standard cooling unit with sealed compressor with protective devices has been provided below the chamber for safe and efficient working. Heating arrangement has made within the chamber for higher temperature. Inner air circulating system is provided to achieve uniform temperature in the whole chamber. A control panel is provided with various indicators such as on off switch, L - shaped thermometer, etc. The BOD Incubator is supplied with cord & plug, etc. The equipment is workable on 220V AC 50 Hz single phase.

 

Details : Aluminum / SS Chamber sizes :

• 24" x 18" x 6" - 4 cubic ft.
• 33" x 20" x 16.5" - 6 cubic ft.
• 34.5" x 22.5" x 22.5" -10 cubic ft.
• 36" x 26" x 23" - 12 cubic ft.
• 27.5" x 25.5" x 35.5" -15 cubic ft.

 

Optional accessories :

• Timer 0.24 hours day night cycle.
• Co2/air mixer nozzle is provided.
• Internal illumination with 3 fluorescent tubes.
• Digital temp. Indicator-cum-Controller.
• Micropcessor PID digital temp. Indicator-cum-controller.
• Automatic Voltage Stabilizer 3-5 KVA (recommended must.)

Hot air ovens are suitable for temperatures up to 250C for chemicals, glassware in laboratories, research institutions, industries, hospitals & R & D centers.This suits various applications like heating, drying, sterilizing & baking.All external cases are made of mild steel, often with strong seamless welding & covered with a thick layer of stoved epoxy-polyester paint. This provides a strong, highly scratch & heat resistant surface for a long-lasting attractive finish.Internal surfaces (including the doors ) are manufactured from Stainless Steel, with great care in order to eliminate sharp edges. The Double walled chamber is filled with high-grade insulation to prevent heat loss. Elements are of the sheathed black heat type are put inside beads & placed at the bottom & in both the side ribs are placed for uniform temperature. The door Closes onto an as pesto's-gasket the shelves slide neatly into the fixed runners. 'The fixed ventilators are provided on both sides of the wall. The thermometer is provided on the top of the oven to check the temperature.The oven is mounted on four rubber feet to prevent slipping & this protects the bench surface. Internal surfaces (including the doors) are manufacture fromStainless Steel. The control panel house a main ON/OFF switch indicator lamp & temperature setting knob. The scale is calibrated in 5C Steps.OVEN SIZE: 45X45X45CM60X60X60CM28X28X40

Product Description

• Design Structures : Aerodynamic, floor mounted
• Air Flow Type : Automatic bypass type
• Construction (Exteriors) : Available in two options:-
• Stainless Steel 304gr. Outside & 316gr. S.S.Inside.
• Epoxy power coated 18 & 22 Gauge Galvanized Steel
• Baffle arrangement : 2 Point suction section with baffle to ensure smooth And immediate exhaust of fumes. As per ASHRAE & EN norms.
• Airfoil : Flush powder coated airfoil mounted on the worktop.
• Worktop : Available in following options
• Chemical resistant splash & spiliage proof jet black Granite worktop. Sink, water tap with drain arrangement worktop fitted with oval shaped 100 x 200mm PP cup-sink for drainage.
• Epoxy top (at extra cost)
• Stainless Steel 316gr.
• Sash (Shutter) : Vertical Sliding Counter balanced toughened glass (5mm thick / Polycarbonate fitted in the powder coated Aluminum. Clear sash open height =500mm-675mm According to size & Fume Hood.
• Service Fittings : Remotely operated color coded ( as per international standard) total three services valves with SS breaded flexible hose & brass fittings (1 for water & 2 for gases).
• Lighting : CFL tube light (1x36W) with Polycarbonate enclosed for Better Illumination with less power concumption.
• Electrical utilitie : Four nos electrical sockets 15/5amp & switches, ‘North West / HAVELLS make 50Hz switches have LED to Indicators to show ON position of switches to be Provided. Control panel provided with starter for blower.
• Complete rigid structure to support fume hood.
• Double skin shutter with self closing hinges.
• Digital Air Flow : This device is an accessory for fume hood to indicate the Approximate face velocity of airflow with primary
• Purpose of warning when a low flow condition occurs. Red & LED’s correspond to low & normal flow rates. When flow decreases from normal to low an audible Alarm will also actuate requiring manual Acknowledgement for silence.
• Centrifugal Blowe : Silent high efficiency blower, consisting of continuous Rating motor and chemical resistant impeller. The blower Designed to give face velocity of 80 to 120 feet/minute (FPM) as per ANSI/AIHA Z9.5 at the safe working Height.
• Air suction capacity : Silent 650 CFM confirming to international face velocity Norms and a per fume hood airflow pattern. Fume Hood (Stainless Steel) Frame of S.S.304grade from outside & 316 grade inside.

Uses : For drying and curing of samples at particular temperature and duration To determine the effect of ageing on various physical properties of any type of material like fabric, yarn, paper, rubber, plastic, Powder and metals.

 

Sizes available are :

• 12" x 12" x 12" (28 Ltr.)
• 14" x 14" x 14" (45 Ltr.)
• 18" x 18" x 18" (95 Ltr.)
• 24" x 24" x 24" (224 Ltr.)

• Made of Mild Steel duly powder coated.
• Granite Working Platform.
• High-Speed Centrifugal Blowers.
• Front Sash with counterweights.
• Fluorescent illumination lights.
• Water tap and PP sink.
• Provision for gas and air Connection Storage cupboard.
• 15/5 Amp Switches and Socket.

Working Area Size 90x60x60cm.Working Area Size 120x60x60cm.Working Area Size 120x75x75cm.

Product Description

• Design Structures : Aerodynamic, floor mounted
• Air Flow Type : Automatic bypass type
• Construction (Exteriors) : Available in two options:-
• Stainless Steel 304gr. Outside & 316gr. S.S.Inside.
• Epoxy power coated 18 & 22 Gauge Galvanized Steel
• Baffle arrangement : 2 Point suction section with baffle to ensure smooth And immediate exhaust of fumes. As per ASHRAE & EN norms.
• Airfoil : Flush powder coated airfoil mounted on the worktop.
• Worktop : Available in following options
• Chemical resistant splash & spiliage proof jet black Granite worktop. Sink, water tap with drain arrangement worktop fitted with oval shaped 100 x 200mm PP cup-sink for drainage.
• Epoxy top (at extra cost)
• Stainless Steel 316gr.
• Sash (Shutter) : Vertical Sliding Counter balanced toughened glass (5mm thick / Polycarbonate fitted in the powder coated Aluminum. Clear sash open height =500mm-675mm According to size & Fume Hood.
• Service Fittings : Remotely operated color coded ( as per international standard) total three services valves with SS breaded flexible hose & brass fittings (1 for water & 2 for gases).
• Lighting : CFL tube light (1x36W) with Polycarbonate enclosed for Better Illumination with less power concumption.
• Electrical utilitie : Four nos electrical sockets 15/5amp & switches, ‘North West / HAVELLS make 50Hz switches have LED to Indicators to show ON position of switches to be Provided. Control panel provided with starter for blower.
• Complete rigid structure to support fume hood.
• Double skin shutter with self closing hinges.
• Digital Air Flow : This device is an accessory for fume hood to indicate the Approximate face velocity of airflow with primary
• Purpose of warning when a low flow condition occurs. Red & LED’s correspond to low & normal flow rates. When flow decreases from normal to low an audible Alarm will also actuate requiring manual Acknowledgement for silence.
• Centrifugal Blowe : Silent high efficiency blower, consisting of continuous Rating motor and chemical resistant impeller. The blower Designed to give face velocity of 80 to 120 feet/minute (FPM) as per ANSI/AIHA Z9.5 at the safe working Height.
• Air suction capacity : Silent 650 CFM confirming to international face velocity Norms and a per fume hood airflow pattern. Fume Hood (Stainless Steel) Frame of S.S.304grade from outside & 316 grade inside.

BOD Incubator is designed for low temperature incubation and determination of Bio Chemical Oxygen Demand (B.O.D). The BOD Incubator comes with a double wall construction. The Inner chamber is made of richly anodized aluminum or highly polished stainless steel with with two / three removable perforated shelves. The exterior chamber of the BOD Incubator is made of thick mild steel sheet duly finished in enamel paint. Outer double wall door is provided with magnetic gasket and lock & key arrangement. The inner door is made out of clear acrylic sheet allowing inspection of material in the chamber without disturbing the chamber temperature. Door operated inner illumination has been provided. The gap between walls of equipment are filled with glass wool for temperature insulation. The cabinet is mounted on castors. The temperature in the BOD Incubator is controlled by a sensitive thermostat from 5oC to 50oC ± 1oC. For lower temperature working, a standard cooling unit with sealed compressor with protective devices has been provided below the chamber for safe and efficient working. Heating arrangement has made within the chamber for higher temperature. Inner air circulating system is provided to achieve uniform temperature in the whole chamber. A control panel is provided with various indicators such as on off switch, L - shaped thermometer, etc. The BOD Incubator is supplied with cord & plug, etc. The equipment is workable on 220V AC 50 Hz single phase.

 

Details : Aluminum / SS Chamber sizes :

• 24" x 18" x 6" - 4 cubic ft.
• 33" x 20" x 16.5" - 6 cubic ft.
• 34.5" x 22.5" x 22.5" -10 cubic ft.
• 36" x 26" x 23" - 12 cubic ft.
• 27.5" x 25.5" x 35.5" -15 cubic ft.

 

Optional accessories :

• Timer 0.24 hours day night cycle.
• Co2/air mixer nozzle is provided.
• Internal illumination with 3 fluorescent tubes.
• Digital temp. Indicator-cum-Controller.
• Micropcessor PID digital temp. Indicator-cum-controller.
• Automatic Voltage Stabilizer 3-5 KVA (recommended must.)

Hot air ovens are suitable for temperatures up to 250C for chemicals, glassware in laboratories, research institutions, industries, hospitals & R & D centers.This suits various applications like heating, drying, sterilizing & baking.All external cases are made of mild steel, often with strong seamless welding & covered with a thick layer of stoved epoxy-polyester paint. This provides a strong, highly scratch & heat resistant surface for a long-lasting attractive finish.Internal surfaces (including the doors ) are manufactured from Stainless Steel, with great care in order to eliminate sharp edges. The Double walled chamber is filled with high-grade insulation to prevent heat loss. Elements are of the sheathed black heat type are put inside beads & placed at the bottom & in both the side ribs are placed for uniform temperature. The door Closes onto an as pesto's-gasket the shelves slide neatly into the fixed runners. 'The fixed ventilators are provided on both sides of the wall. The thermometer is provided on the top of the oven to check the temperature.The oven is mounted on four rubber feet to prevent slipping & this protects the bench surface. Internal surfaces (including the doors) are manufacture fromStainless Steel. The control panel house a main ON/OFF switch indicator lamp & temperature setting knob. The scale is calibrated in 5C Steps.OVEN SIZE: 45X45X45CM60X60X60CM28X28X40

Product Description

• Design Structures : Aerodynamic, floor mounted
• Air Flow Type : Automatic bypass type
• Construction (Exteriors) : Available in two options:-
• Stainless Steel 304gr. Outside & 316gr. S.S.Inside.
• Epoxy power coated 18 & 22 Gauge Galvanized Steel
• Baffle arrangement : 2 Point suction section with baffle to ensure smooth And immediate exhaust of fumes. As per ASHRAE & EN norms.
• Airfoil : Flush powder coated airfoil mounted on the worktop.
• Worktop : Available in following options
• Chemical resistant splash & spiliage proof jet black Granite worktop. Sink, water tap with drain arrangement worktop fitted with oval shaped 100 x 200mm PP cup-sink for drainage.
• Epoxy top (at extra cost)
• Stainless Steel 316gr.
• Sash (Shutter) : Vertical Sliding Counter balanced toughened glass (5mm thick / Polycarbonate fitted in the powder coated Aluminum. Clear sash open height =500mm-675mm According to size & Fume Hood.
• Service Fittings : Remotely operated color coded ( as per international standard) total three services valves with SS breaded flexible hose & brass fittings (1 for water & 2 for gases).
• Lighting : CFL tube light (1x36W) with Polycarbonate enclosed for Better Illumination with less power concumption.
• Electrical utilitie : Four nos electrical sockets 15/5amp & switches, ‘North West / HAVELLS make 50Hz switches have LED to Indicators to show ON position of switches to be Provided. Control panel provided with starter for blower.
• Complete rigid structure to support fume hood.
• Double skin shutter with self closing hinges.
• Digital Air Flow : This device is an accessory for fume hood to indicate the Approximate face velocity of airflow with primary
• Purpose of warning when a low flow condition occurs. Red & LED’s correspond to low & normal flow rates. When flow decreases from normal to low an audible Alarm will also actuate requiring manual Acknowledgement for silence.
• Centrifugal Blowe : Silent high efficiency blower, consisting of continuous Rating motor and chemical resistant impeller. The blower Designed to give face velocity of 80 to 120 feet/minute (FPM) as per ANSI/AIHA Z9.5 at the safe working Height.
• Air suction capacity : Silent 650 CFM confirming to international face velocity Norms and a per fume hood airflow pattern. Fume Hood (Stainless Steel) Frame of S.S.304grade from outside & 316 grade inside.

Uses : For drying and curing of samples at particular temperature and duration To determine the effect of ageing on various physical properties of any type of material like fabric, yarn, paper, rubber, plastic, Powder and metals.

 

Sizes available are :

• 12" x 12" x 12" (28 Ltr.)
• 14" x 14" x 14" (45 Ltr.)
• 18" x 18" x 18" (95 Ltr.)
• 24" x 24" x 24" (224 Ltr.)

• Made of Mild Steel duly powder coated.
• Granite Working Platform.
• High-Speed Centrifugal Blowers.
• Front Sash with counterweights.
• Fluorescent illumination lights.
• Water tap and PP sink.
• Provision for gas and air Connection Storage cupboard.
• 15/5 Amp Switches and Socket.

Working Area Size 90x60x60cm.Working Area Size 120x60x60cm.Working Area Size 120x75x75cm.