A Dust particulate monitor is a device that is mounted in the discharge stack of a dust collector and continuously monitors the amount of particulate discharge. The particulate monitor uses a technology known as Triboelectric or Triboelectricity. When two different materials come in contact, it is likely that one will leave with more electrons than it started with and the other will leave with less, this is called Triboelectric Effect. The interaction between the probe and particles produces a charge transfer within the probe. The charge is then converted to an output signal. Dust Particulate Monitoring systems TECHNICAL SPECIFICATION  Measuring Principle Dynamic Detection Principle,   DDP (Scintillation) Operating Wavelength 510 – 540 nm (green LED)Measurement Reading Concentration (mg/m3) Measuring Range 0 – 1000 mg/m3 (user configurable) Path Length (duct diameter) 0.5 – 10 m (flange-to-flange separation) Accuracy + / - 2 %Flue gas flow rate ! 1.0 m/s Resolution 0.1 mg/m3 (display resolution)Damping 1 – 60 s (user selectable)Drift with Temperature POWER AIR REQUIREMENTS  Voltage +24 Vdc (optional 90-260 Vac PSU available)Nominal Current Consumption 400 mAPower Up Current Consumption 400 mAPurge Air Supply Volume 50 – 200 L/min (to each air purge body)Purge Air Quality Suitably filtered, oil free and dry INTERFACE OPTIONS  Serial Comms ModBus RTU via RS485Internal USB (OI)External USB (RX)Analogue Outputs 4.0 – 20 mA (isolated and scalable)Relay Contacts 3 A @ 30 Vdc (signal level and service alarms) PHYSICAL ​Ambient Operating Temperature -20 – +55 °C (air temperature around the equipment)Exhaust Gas Temperature Up to +600 °C (heat insulating gaskets included)Ambient Operating Humidity 0 – 100 %Ingress Protection IP65 for external useMaterials 316 Stainless Steel (powder coated)Dimensions 153 x 120 x 122 mm (measuring head)Weight 2.5 kg per head  Specification : Range 0-1000 Mg/M3 Sensor Base Systems Style Integral &  Remote Remote Sensor Enclosure: Cost Aluminum, Electrostatically powder coating Probe Material: 316 Stainless Steel (Slandered) other materials available Insulator material: Extended High Performance (PFA) Temperature up to 250 C Ceramic (High temperature up to 550 Deg C ) Electronics 18 – 32 V DC () at the unit  230V AC (Controller) Output: 4-20mA & SPDT Relay Probe Insertion length: 3” to 36” ( 7.6 Cm to 91.4 Cm) Installation Weld the supplied fitting into the pipe or Duct and insert Sensor  Sensor Mounting Flanged  ½” Male NPT  Quick release.

• Display5 &1/2 LED Display.
• Meter Size:96 mm X 96 mm X 50 mm
• Panel Cutout92 mm X 92 mm
• Power Supply230 V +/- 10% 50 Hz. AC
• Linearity±1% Of Full Range
• Repeatability±0.5% Of Full Range
• Operating Temp.0 – 70 Deg C Max.
• Operating Pressure0 – 4 Kg/Cm2 Max.
• Protection RatingIP-65 For Sensor.
• Inputs- Flow Sensor(VT-S-04) P.P Sensor.
• FunctionFlow Rate Indicator Cum Totalizer
• ControlON/OFF 2 relay O/Ps.

• Resolution1/0.1 Digits.
• Accuracy± 1 % of Full Scale Value.
• Dual Displayone at Transmitter (Sampler) & other at monitoring unit.(controller).
• Enclosureboth Water Proof & Flame Proof.
• ProtectionIP - 65 For Gas Gr. IIA & IIB. CCOE & CMRI approved.
• Ranges from0 - 200 ppm & 0 - 4000 ppm.

• MaterialPlastic
• Brand NameSheetal Instrumentation
• ColorBlack,Red
• ConditionNew
• ApplicationIndustrial Use
• TypeFlow Sensors
• Accuracy+/- 2%.
• OutputPulses.
• Warranty1year
• Country of OriginIndia

A Dust particulate monitor is a device that is mounted in the discharge stack of a dust collector and continuously monitors the amount of particulate discharge. The particulate monitor uses a technology known as Triboelectric or Triboelectricity. When two different materials come in contact, it is likely that one will leave with more electrons than it started with and the other will leave with less, this is called Triboelectric Effect. The interaction between the probe and particles produces a charge transfer within the probe. The charge is then converted to an output signal. Dust Particulate Monitoring systems TECHNICAL SPECIFICATION  Measuring Principle Dynamic Detection Principle,   DDP (Scintillation) Operating Wavelength 510 – 540 nm (green LED)Measurement Reading Concentration (mg/m3) Measuring Range 0 – 1000 mg/m3 (user configurable) Path Length (duct diameter) 0.5 – 10 m (flange-to-flange separation) Accuracy + / - 2 %Flue gas flow rate ! 1.0 m/s Resolution 0.1 mg/m3 (display resolution)Damping 1 – 60 s (user selectable)Drift with Temperature POWER AIR REQUIREMENTS  Voltage +24 Vdc (optional 90-260 Vac PSU available)Nominal Current Consumption 400 mAPower Up Current Consumption 400 mAPurge Air Supply Volume 50 – 200 L/min (to each air purge body)Purge Air Quality Suitably filtered, oil free and dry INTERFACE OPTIONS  Serial Comms ModBus RTU via RS485Internal USB (OI)External USB (RX)Analogue Outputs 4.0 – 20 mA (isolated and scalable)Relay Contacts 3 A @ 30 Vdc (signal level and service alarms) PHYSICAL ​Ambient Operating Temperature -20 – +55 °C (air temperature around the equipment)Exhaust Gas Temperature Up to +600 °C (heat insulating gaskets included)Ambient Operating Humidity 0 – 100 %Ingress Protection IP65 for external useMaterials 316 Stainless Steel (powder coated)Dimensions 153 x 120 x 122 mm (measuring head)Weight 2.5 kg per head  Specification : Range 0-1000 Mg/M3 Sensor Base Systems Style Integral &  Remote Remote Sensor Enclosure: Cost Aluminum, Electrostatically powder coating Probe Material: 316 Stainless Steel (Slandered) other materials available Insulator material: Extended High Performance (PFA) Temperature up to 250 C Ceramic (High temperature up to 550 Deg C ) Electronics 18 – 32 V DC () at the unit  230V AC (Controller) Output: 4-20mA & SPDT Relay Probe Insertion length: 3” to 36” ( 7.6 Cm to 91.4 Cm) Installation Weld the supplied fitting into the pipe or Duct and insert Sensor  Sensor Mounting Flanged  ½” Male NPT  Quick release.

• Display5 &1/2 LED Display.
• Meter Size:96 mm X 96 mm X 50 mm
• Panel Cutout92 mm X 92 mm
• Power Supply230 V +/- 10% 50 Hz. AC
• Linearity±1% Of Full Range
• Repeatability±0.5% Of Full Range
• Operating Temp.0 – 70 Deg C Max.
• Operating Pressure0 – 4 Kg/Cm2 Max.
• Protection RatingIP-65 For Sensor.
• Inputs- Flow Sensor(VT-S-04) P.P Sensor.
• FunctionFlow Rate Indicator Cum Totalizer
• ControlON/OFF 2 relay O/Ps.

• Resolution1/0.1 Digits.
• Accuracy± 1 % of Full Scale Value.
• Dual Displayone at Transmitter (Sampler) & other at monitoring unit.(controller).
• Enclosureboth Water Proof & Flame Proof.
• ProtectionIP - 65 For Gas Gr. IIA & IIB. CCOE & CMRI approved.
• Ranges from0 - 200 ppm & 0 - 4000 ppm.

• MaterialPlastic
• Brand NameSheetal Instrumentation
• ColorBlack,Red
• ConditionNew
• ApplicationIndustrial Use
• TypeFlow Sensors
• Accuracy+/- 2%.
• OutputPulses.
• Warranty1year
• Country of OriginIndia