SAF Deep Pleat ASHRAE [M6-F9]

Our SAF Deep Pleat ASHRAE is a ruggedly constructed, heavy duty, high efficiency filter. A special dual layer, graded density media ensures extremely high dust holding capacity & therefore lower operating pressure loss. The high efficiency and moisture resistance of the filter keeps the inside clean & protects against moisture and salt.

SAF Deep Pleat HEPA [H10-H14]

Our SAF HEPA (High Efficiency Particulate Air) filter is constructed from high quality wet laid micro-glass media and uses corrugated aluminum separators. The pleat pitch is designed for minimum air flow resistance and the spacer edges are 'safety rolled' to prevent media puncture. The filter is sealed to the frame with a two - part spongy PU resin to ensure zero leakage and zero transit damage.

Mini Pleat ASHRAE [M6-F9]

SAF's Mini Pleat ASHRAE filters offer's various Boons over conventional deep pleat ASHRAE filters, such as higher flow capacities, less space, reduced resistance to flow, and greatly enhanced dust holding capacities. It serves as an excellent final filter for in air intake systems of combustion engines and as a final filter in HVAC systems.

SAF 's premium range of Mini Pleat ULPA filters are Manufactured with dense, corrosion resistant PTFE membrane and protective substrates, this filter is water resistant and meets the requirements of UL 900, Class 1. The PTFE membrane pack assures precision in pleat spacing and height to reduce dead-spots and promote consistent and uniform air distribution throughout the filter. The anodized extruded aluminum frame is available with gasket seal, gel seal or knife edge for fluid grid Usage Zone.

SAF G-Pac Pleated [M5-F7]

The new G-Pac Pleat's advanced pleating technology increases media area per filter, reducing resistance to air flow and maximizing service life. The G-Pac pleats frame is formed with high impact plastic to precise dimensions for a secure fit in either housing or holding frames. The frame is impervious to moisture, rigid, and exceptionally lightweight for safe and easy handing and installation. Pleats are thermo formed at the tips to maintain integrity. Uniformed beads of foamed hot- melt separate the pleats to the most efficient and exacting tolerances to lower air drag across the filter. The media pack is resin bonded on all four sides of the filter frame, eliminating the possibility of air by pass around the filter media

SAF Cell Compact [M5-F9]

'AFi's Cell Compact' mini pleated filters offer substantial advantages over conventional deep pleat ASHRAE filters, not the least of which are higher flow capacities, less space, reduced resistance to flow, and greatly enhanced dust holding capacities. It serves as an excellent final filter for in air intake systems of combustion engines and as a final filter in HVAC systems.

SAF Deep Pleat ASHRAE [M6-F9]

Our SAF Deep Pleat ASHRAE is a ruggedly constructed, heavy duty, high efficiency filter. A special dual layer, graded density media ensures extremely high dust holding capacity & therefore lower operating pressure loss. The high efficiency and moisture resistance of the filter keeps the inside clean & protects against moisture and salt.

SAF Deep Pleat HEPA [H10-H14]

Our SAF HEPA (High Efficiency Particulate Air) filter is constructed from high quality wet laid micro-glass media and uses corrugated aluminum separators. The pleat pitch is designed for minimum air flow resistance and the spacer edges are 'safety rolled' to prevent media puncture. The filter is sealed to the frame with a two - part spongy PU resin to ensure zero leakage and zero transit damage.

Mini Pleat ASHRAE [M6-F9]

SAF's Mini Pleat ASHRAE filters offer's various Boons over conventional deep pleat ASHRAE filters, such as higher flow capacities, less space, reduced resistance to flow, and greatly enhanced dust holding capacities. It serves as an excellent final filter for in air intake systems of combustion engines and as a final filter in HVAC systems.

SAF 's premium range of Mini Pleat ULPA filters are Manufactured with dense, corrosion resistant PTFE membrane and protective substrates, this filter is water resistant and meets the requirements of UL 900, Class 1. The PTFE membrane pack assures precision in pleat spacing and height to reduce dead-spots and promote consistent and uniform air distribution throughout the filter. The anodized extruded aluminum frame is available with gasket seal, gel seal or knife edge for fluid grid Usage Zone.

SAF G-Pac Pleated [M5-F7]

The new G-Pac Pleat's advanced pleating technology increases media area per filter, reducing resistance to air flow and maximizing service life. The G-Pac pleats frame is formed with high impact plastic to precise dimensions for a secure fit in either housing or holding frames. The frame is impervious to moisture, rigid, and exceptionally lightweight for safe and easy handing and installation. Pleats are thermo formed at the tips to maintain integrity. Uniformed beads of foamed hot- melt separate the pleats to the most efficient and exacting tolerances to lower air drag across the filter. The media pack is resin bonded on all four sides of the filter frame, eliminating the possibility of air by pass around the filter media

SAF Cell Compact [M5-F9]

'AFi's Cell Compact' mini pleated filters offer substantial advantages over conventional deep pleat ASHRAE filters, not the least of which are higher flow capacities, less space, reduced resistance to flow, and greatly enhanced dust holding capacities. It serves as an excellent final filter for in air intake systems of combustion engines and as a final filter in HVAC systems.