Post Buy Requirement
SE
Add Review

Our Products

  1. Business And Corporate Gifts 14 Products available
  2. Wires 9 Products available
  3. Microcontroller 3 Products available
  4. Electronic Development Boards 3 Products available
  5. Telecommunication Equipment & System

    2 Products available
  6. Access Control Reader

    2 Products available
  7. Sensors

    2 Products available
  8. Electric & Electronic Active Devices

    1 Products available
  9. Computer Cables, Adapters & Modules

    1 Products available
  10. Others Products 69 Products available

Electric Circuit Components & Parts

We offer the best product range of SERIAL LCD, AVR USB JTAG ICE EMULATOR DEBUG PROGRAMMER, FPGA CPLD USB BLASTER ALTRA PROGRAMMER, 433MHZ RF Wireless Receiver Module & Transmitter Module and 315MHZ RF Wireless Receiver Module & Transmitter Module.

SERIAL LCD

This is the latest evolution of our serial lcd. Included on a single board is a 16x2 lcd and an embedded circuit based around a pic 16f88 and others. The serial lcd is a simple and cost effective solution for interfacing to liquid crystal displays (lcds) based on hd44780 controller. The module takes incoming 9600 bps ttl level signals and display those characters on the lcd screen. Only three wires +5v, gnd and signal are needed to interface to the lcd. Features: operational backspace simple 3 pin interface to control lcd from 9600 baud rate from any microcontroller contrast adjustment preset backlight can be controlled from software full control of lcd from serial data auto-wrapping of displayed data incoming buffer stores up to 80 characters pulse width modulation of backlight allows direct control of backlight brightness and current consumption all surface mount design allows a backpack that is half the size of the original faster boot-up time boot-up display can be turned onoff via firmware user definable splash screen hardware specifications: the serial lcd should only be powered by 5v dc. Higher than 5.5v will cause damage to the lcd. The serial lcd uses 3ma with backlight turned off and 60ma with the backlight activated.
View Complete Details

AVR USB JTAG ICE EMULATOR DEBUG PROGRAMMER

Through the JTAG mouth MCU software and hardware of the simulation, also by the mouth of single-chip processor JTAG download a program or modify a molten silk. The support of the single chip microcomputer simulation models: ATMega16, ATmega16L, ATMega162, ATmega162V, ATmega165, ATmega165V, ATMega169, ATmega169V, ATMega32, ATMega323, ATmega323L, ATmega32L, ATMega64, ATmega64L, ATMega128, ATmega128L, AT90CAN128ATMega16, ATmega16L, ATMega162, ATmega162V, ATmega165, ATmega165V, ATMega169, ATmega169V, ATMega32, ATMega323, ATmega323L, ATmega32L, ATMega64, ATmega64L, ATMega128, ATmega128L, AT90CAN128. Support JTAG simulation method, JTAG program mode, the standard JTAG interface (with ATMEL original). Our production of original version simplified products, with two 74 HC125 as a buffer drive, effectively protect the chip program not be developed, the save unnecessary trouble; Cluster cost-effective products. FEATURES Compatible with AVR JTAG USB emulator device.AVR Studio firmware upgradeable, the Update-JTAG manual will allow the device update to most current firmware and support the device list on latest AVR studio development softwareUSB data transfer speed up the update rate and debug performance.Compatible with AVRISP programmer. Same device support and updateable by AVR Studio3 LEDs for debugger Status.
View Complete Details

FPGA CPLD USB BLASTER ALTRA PROGRAMMER

The Altera USB Blaster is used to program FPGA boards such as the Alterra Cyclone II. FEATURES High quality.Fully compatible with original Altera USB-Blaster.Supported target voltage : 1.0V-5.5V.Support all ALTERA device.Support NiosII embedded core based debug.Supports Quartus II SignalTap? II Logic Analyzer (for logic analysis).High performance, 6 times faster than ByteBlasterII.USB interface with status and Power LED.Support AS, PS and JTAG mode
View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us