Laboratory Apparatus #3824030

Melting point is displayed on the 3 digit mounted on the front panel, The instrument basically consists of a miniature furnace with controllable heating rate arrangement, an air circulating arrangement and a digital temp. indicating circuitry with necessary controls, Temp. at the melting point is latched on the digital display and the furnace is automatically cut-off. The rate of rise in temp. can be precisely controlled by a knob on the front panel. The instrument gives audio & visual indications, on reaching the temp. at which the sample melts. The temp. indicating point of the sample remains displayed on the panel till the clear press switch marked CLEAR is operated. The range of the instruments is 40C to 350C. Readability is 1.0C with accuracy of 1C. The unit works on 230 Volts / 50Hz. A.C.

It's the most ideal "LEAK TEST" instrument for checkingBlister PacksandStrips.It makes the conventional dessicator with a huge vacuum pump, obsolete. The Vacuum Pump ensures that a high level of vacuum is created in the shortest possible time. And the die-pressed, polycarbonate vacuum dessicator sustains the vacuum for a long time. A vacuum gauge is provided to indicate the vacuum level. This is connected to the isolation valve which helps disconnect the source, thereby avoiding the need for running the vacuum pump continuously. While its amazing compactness saves valuable space in process laboratories, a 0-60 minute timer helps the operator attend to other chores at a time!

Paper Electrophoresis Apparatus (Horizontal Migration Cell) is made of transparent, inert acrylic plastic sheet. PLATINUM ELECTRODES OF 99.9% PURITY extend through the entire width of the buffer compartment. It can accommodate six paper strips of 4 cm width or paper/sheet upto 28 cm width on removable special strip carrier placed on the bed of the chamber

For determination of melting points upto 350C. The mounted block is illuminated from below by a lamp fixed in its housing. The aluminium block accept three capillary tubes and mercury thermometer. The temp. is regulated by energy regulator fitted to the unit. The lamp. provides uniform and shadow less regulator fitted to the unit. Supplied without capillary tubes and thermometer.

(B) WITH DIGITAL TEMP. INDICATOR, COOLING FAN

Consists of S.S. holders in mainfold of 3 of 6 to hold 47 m.m. dia, . membrane filters, The tops of the holders are connected to the outlets of the flushing tube with silicone tubing and glass stop cock. A vacuum resistant flask or woulf bottle must be placed between the manifold and vacuum pump. (Supplied without Wolfs Bottle and Vaccum/ Pressure Pump). These units are used for sterlity testing when the membranes filter is to be removed from the holder for incubation in culture media. Filtration areas is 12.5cm and has a holding capacity of 250ml. Though only vacuum is required for filleration, some pressure is required for flushing liquids.

• 3 Branch Sterility Test Unit. (Made from SS-316)
• 6 Branch Sterility Test Unit (Made from SS-316)

Asian Melt Flow Index Apparatus for plastic measures the melt flow index of plastic material. The system consists of a heated extruder tube, an interchangeable jet through which the material under test is extruded, and a piston with dead weights to apply the specified pressure on the material inside the extruder tube. The extruder tube is made from carbon steel and is heated by means of a Bend Heater, which surrounds its outer circumference. A PID controller is provided to indicate & control the temperature of the tube. The heater logged with mineral wool insulation. The assembly is fixed on a rigid stand. The bottom of the tube is lagged with a insulation of PTFE to prevent sticking of the extrudate. The jet through with the extruder is pushed out is made from hardened and ground die steel. It is held at the bottom of the extruder tube. The piston made from silver steel relieved at the upper end is provided to push the extrudate out of the jet. The piston moves inside the cavity of tube. A sleeve to provide to guide the relieved portion of the piston. The top of the piston carries a plate-form for keeping the load on. The plate-form is thermally insulated from the load. The extruder tube assembly is mounted on a metal box. A sheet metal control panel is mounted on the side of the equipment & houses the PID Controller, DIGITAL PRESET TIMER & other electronic components. Cleaning tools for tube cavity and jets & stoppers & cutter for the extrudate are also supplied with the equipments.

A Perspex organ bath with fine thermostatic temperature control; electric stirrer; and complete set of accessories, making it a versatile unit for all research work. Bath 12"x9"x8", with leak proof dovetailed joints, resting in sturdy metal frame; top of the bath carries a 1"x3/8" thick band, for fixing accessories, Inside the bath is a metal sheathed heating element (easily replaceable), controlled by means of a fine adjustable thermostat with sensitivity 5C.

The stirrer unit is completely independent and dips in the bath in one corner, fixing on its special stainless steel upright. A MS junction box is fitted to the bath frame, and carries all the electrical leads and connections, Two pilot lamps indicate functioning of the thermostat and stirrer.

Standard components are :

i) Double set of glass inner vessels.
ii) Oxygen tubes
iii) Warming coils
iv) Two stainless steel capillary levers.
v) Four stainless steel uprights with boss heads,

It is designed to meet the requirements of USP Standards suitable for Method-I & Method -II.It can hold two cylinders, capacity : 50 ml and 250 ml. The mechanism provides simultaneously rotating and tapping motion to the cylinders for packing the sample under test evently and uniformly together.

Features :Easy to Operate all the functions. Two Cylinders holder having easy mechanism to insert and take out. Simultaneous tapping and rotating assures an evenly packed surface. Calculation of test results will be displayed directly on the instrument panel by feeding the correct data. An audible alarm after the test is over The "THERMONIK" Bulk Density is specially designed to study the packing down of powder beds of different pharmaceuticals and chemicals powders, flakes, pellets, granules and other bulk substances. Bulk Density is an essential test required in the process of tablet manufacturing, Capsule filling and cosmetic manufacture. The Bulk density apparatus is equipped with Microcomputer Based 'Digital Display' System. The "TOUCH SWITCHES" are provided on the front panel of the apparatus for setting total number of strokes to the glass cylinders. Each stroke of the cylinder is displayed on the "Digital Display' window on the panel. The Up and down movement of the cylinders stop automatically at the Pre-set number and at the same time an audible Alarm sounds indicating the test is over. The advantage of Micro-Computer based Digital Display over the Old type model with the mechanical Timer is that "Digital Display" of total strokes gives accurate and exact number of Strokes given to the cylinders. The Touch Switches Can be set to any required strokes start right from minimum 1Stroke to 9999 strokes maximum. Specification : Display: 4 Digits LED Power Supply: 230 V/ AC 50 Hz. Dimension: 280 mm x 290 mm x 275 mm Weight: Net Wt 15 kgs. In the new and sophisticated model C-BD 100 Calculator is not required for test results. The results will be displayed directly on the instrument panel by feeding the correct data. Apparatus is suitable for working on 230 Volts, Single Phase A.C. 50Hz. Supplied with a pair of 50 ml glass cylinders and connecting cable. 100ml and 250ml Cylinders will be supplied at extra cost.

A Perspex organ bath with fine thermostatic temperature control; electric stirrer; and complete set of accessories, making it a versatile unit for all research work. Bath 12"x9"x8", with leak proof dovetailed joints, resting in sturdy metal frame; top of the bath carries a 1"x3/8" thick band, for fixing accessories, Inside the bath is a metal sheathed heating element (easily replaceable), controlled by means of a fine adjustable thermostat with sensitivity 5C.

The stirrer unit is completely independent and dips in the bath in one corner, fixing on its special stainless steel upright. A MS junction box is fitted to the bath frame, and carries all the electrical leads and connections, Two pilot lamps indicate functioning of the thermostat and stirrer.

Standard components are :

i) Double set of glass inner vessels.
ii) Oxygen tubes
iii) Warming coils
iv) Two stainless steel capillary levers.
v) Four stainless steel uprights with boss heads,

Used to determine the durability and abrasivness of tablets. A transparent perpex drum (made of imported perspex sheet 6.4 mm thick) 300 mm dia x 35 mm. deep and -white cover disc and nut, also a shaped radial fixed blade which carries the tablets along with it up to the central height and lets them off while the drum is rotating. Thus the tablets rub against each other without any hard impact. The drum rotates at a fixed speed of 30 R.P.M. by a geared motor and the rotation period is controlled by a timer (imported time switch duration I to 15 minutes) per determined end preset. The motor unit is housed in a shaped steel cabinet with shaft extended on one side upon which the drum rotates. Switches with neon indicators and time switch are fitted on a panel and provided work on 220 volts 50 C/s A.C.Digital modelsare also available.

(b) -do- same as above, but with double drum.

For determining neuro-pixicity, muscle tone, balance and motor co-ordination in rats and mice. Consistingof two or three or four compartmentsof 75mm width each with a rotating rod of 25mm diameter having speeds of 5, 10, 15, 20 and 25 rpm with time interval counter in each compartments

POLE CLIMBING APPARATUS SE-346: Our rich industry experience and knowledge help us manufacture and supply an extensive range of Pole Climbing Apparatus. In compliance with international industry standards, we manufacture offered product using high grade raw material that is procured from reliable vendors of the market. This product is highly appreciated by our clients for its easy use and long lasting nature.

Suitable for determination of close cup flash point of petroleum production. It is designed as per IP-33 and IS-1448( part -1) 1985 (P:20). It is suitable for oils whose flashes below 70 c.Supplied with oil cup cover assembly fitted with stirrer, thermometer socket, S.S Water Bath, stand & electric heater is fitted at bottom for operation on 220 volts.

Carbon sulphur apparatus is used to detect percentage of Carbon and sulphur in iron and steel. The scale of apparatus burette is directly calibrated in terms of carbon percentage. The apparatus can detect carbon percentage up to 4.5%. By using interchangeable burettes, the measurement can be taken to 0.25%, 0.5%, 1.5% and 4.5%. Th apparatus furnace attains required temperature rapidly and a high accuracy digital pyrometer indicates the furnace temperature. The equipment can detect carbon or sulphur or both.