SCIENTECH INSTRUMENTS

Kamla Nagar, Delhi

Double wailed chamber has inner made up of thick S.S. and outer wall is of thick PCRC sheet duly Powder Coated. A glass window is provided on the front side for an easy inside view. A high speed stirrer with a motor of 1/20 H.P. is fitted to the unit for continuous stirring and thus maintaining a uniform temperature throughout.A speed regulator & digital indicator controller is provided on the front panel to control speed of the stirrer and temperature of bath. The heating mechanism comprises of set of heaters pertaining to faster and slower heating Controls the temperature with a sensitivity of + 0.1C, from ambient to 100 C. To work on 220/230 volts A.C. supply.

IT IS USEFUL FOR SECTIONING OF BONE TISSUE.The wheel is counted balanced with locking device and has automatic feed and release mechanism. A light cover hinged at back is provided for protection of internal parts from dust. Feed range of 1-50 microns in step of 1 micron each, is controlled smoothly by DIAL CONTROL in the rigid front position. For easy positioning of the object to the knife and for returning the feed to the starting position. the feed crank is located at the left side of the microtome, and the feed pawl automatically ceases to function when the feed reaches the extreme forward position. It incorporates ball and flange type object holder for positioning of the object at desired position, Complete with 120 m.m. knife with back and handle in case, 6 block holders. honing stone, bottle of lubrication oil and dust cover.

Made of perforated steedl plate with square holes. Available in following aperature of 125, 160, 100, 90, 80, 75, 63, 53, 50, 45, 40, 37.5, 31.5, 26.5, 25, 22.4, 19, 16, 13.2, 12.2, 11.2, 10.2, 10, 9, 5, 8, 6.7, 6.3, 5.6, 4.75, 2.8 m.m.

• With brass frame 8' dia
• With G.I. frame 12' dia
• With G.I. frame 18' dia

These are sturdy double walled units with outer chamber made of M.S. sheet duly powder coated / Painted inner made up of anodised aluminium or S.S sheet. The gap between inner and outer chamber is filled with high grade glass wool to avoid thermal losses. Beaded heating elements are placed in ribs, at bottom and sides. Inner chamber is provided with ribs for adjusting perforated selves to convenient height. The door is fitted with glass viewing window to facilitate inspection of sample without disturbing the test temperatture. Temperature is controlled by hydraulic type capillary thermostat from ambient to 90C 0.5C. An L- shaped prismatic thermometer is fitted to unit for reading the chamber temperature. Air ventilators are also provided on the sides of unit. To work on 220/230 volts A.C. supply.

Double walled with inside made of Heavy S.S. and outside of M.S. sheet duly powder coated. The gap etween the two walls is fitted with high grade glass wool to minimize thermal loss. Temperature range from ambient to 250C 2C, is controlled by hydraulic capillary type thermostat. A variable speed strirring arrangement is fitted to the unit for maintaining temperature Plug to work on 220/230 volts A.C. supply.

250 x 250 x 250 m.m. 12 Ltr.
300 x 300 x 250 m.m. 20 Ltr.
355 x 355 x 250 m.m. 26 Ltr.

These units are double walled with inner chamber made up of S.S. sheet and outside of M.S. duly powder oated. The gap between the walls is filled with special grade glass wool in order to avoid thermal loses. A drain plug is also fitted to the unit. The inner chamber fitted with immersion type heating element is covered with perforated removable diffuser tray. The cover is provided with the unit as a standard accessory. Temperature from ambient to 100C is controlled by hydraulic capillary type thermostat with an accuracy of 1C. Supplied complete with 220/230 volts A.C. supply.
WIDTH x HEIGHT x DEPTH

300 x 250 x 15 m.m. (for 2 racks)
330 x 300 x 175 m.m. (for 4 racks)
455 x 300 x 175 m.m. (for 6 racks)
605 x 300 x 175 m.m. (for 8 racks)

• With 4 x 15ml Swingout head. (3500 r.p.m.).
• With 6 x 15ml Swingout head. (3500 r.p.m.).
• With 8 x 15ml Swingout head. (3500 r.p.m.).
• With 4 x 50ml Swingout head. (3500 r.p.m.).
• With 4 x 50ml Swingout head. (3500 r.p.m.).
• With Digital Speed & Digital Timer (3500 r.p.m.).

We offer a wide range of Centrifuges for varying application in Clinical & Pathological Labs, Blood Banks, R & D Establishments, Pharmaceutical and Chemical Industries etc.

Ideal heater for the extractors of Soxhlet and other types. This apparatus i suitable to heat soxhlet flasks of 50- 500 ml. It consists of M.S. sheet housing, two vertical & two horizontal rods With adopters and screws to hold the flasks. To work on 220/230 A.C. Supply.

• Unit of 3 test Mantle Type (Without glass parts)
• Unit of 6 test Mantle Type (Without glass parts)

A highly in demand instrument where water is required to be circulated to some external source through an F.H.P. pump. Most useful for circulating water to Abbe Refractometer, condenser coils etc. Temperature from ambient to 90C is controlled through hydraulic type thermostat with an accuracy of 0.5C. Inner chamber made of S.S. and outer chamber made of M.S. Sheet duly powder coated. Inside bath size 8' x 9" x 10 with a cover at side of size : 10'x7' approx. To work on 220/230 Volts .

It consist of six built in photo senser and 4 digit digital counter to indicate the locometer activity. It measures the spontaneous and indicated activity with digital totalizer. It also incorporates electric shock of upto 100 volts for activating rats. The stimulus is variable from 0 to 100V & indicating on meter.

To determination of Chemical Oxygen Demand. It is a solid state block heated unit with provision for samples to be digested at a time in 38 mm. dia reaction vessels with 20 ml sample size ot heat at temp. of 150C + 1C controlled by solid state digital temp. indicator-cum controller
Micro Processor Based (P.I.D.). It has provision for 15 samples and is supplied with 15 nos. glass reaction vessels and 15 nos. air condensers. Fitted with a 2 hour timer, the samples after being digested for 2 hours can be analysed using calorimeter or conventional titration method. To work on 220/230 volts AC.

It is a double walled bath with inner chamber made of stainless and outer wall made of M.S. sheet duly powder coated/ Painted. The gap between outer and inner walls in filled with special grade glass wool insulation. The concentric rings can be removed to accommodate containers of various sizes. Temperature from ambient to 90C 2C is to controlled by thermostat.

• 300 x 250 x 100 m.m. (6 Holes of 75 m.m. Dia)
• 355 x 405 x 100 m.m. (12 Holes of 75 m.m. Dia)

LaboratoryFume Hoodsare one of the most important components used to protect laboratory personnel from exposure to hazardous chemicals and agents used in the laboratory. When used properly, they can provide an effective backup safety device for the containment and exhaust of toxic, offensive or flammable materials when the containment of an experiment or procedure fails and vapors or dust escape from the apparatus being used. We are one of the foremost Chemical Fume Hood Manufacturers and Stainless Steel Fume Hood Suppliers.
The Cabinet is made of thick ply board & reinforced with teak wood whatever necessary interiors coated with asbestos sheets, coated with epoxy paint or convert FRP lining as per requirements.
Working table is covered with glazed ceramic tiles and provided with necessary water inlet & outlets with sink (stainless steel/prosaleen). Provision of water inlet/outlet, sink will be on request only.
Front door is made of 6mm clear glass in laminated teakwood frame and connected with a counter weight balance through a iron rope. The door will have the provision of vertical sliding facility.
Exhaust blower consists of single phase motor, directly connected with a PVC Exhaust blower consists of single phase motor, directly connected with a PVC impeller and enclosed in a epoxy coated MS casing. The rating, speed & capacity of the Blower sill are designed on the basis of the SIZE & VOLUME of the FUME HOOD.
However the suction velocity of the FUME HOOD will be around 100 cfm per square feet.
The exhaust assembly can be of build-in-type or external mount type. The blower assembly will directly be connected with suitable exhaust ducting, which is made of PVC pipes with suitable bend & joints and rain guard.

• Chemical & Fire resistant Phenolic(FRP) Resin Lining inside the Chamber
• Different choice of worktops suitable for a wide range of applications (S.S/ GRANITE/TILES)
• Clear tempered safety glass sash utilizes counter weights for smooth and effortless operations

Options :

• Compact Ductwork System with Exhaust Fan
• Fume Scrubber
• Wash-Down System
• Electrical Wiring
• Solvent Storage Base Cabinet
• Acid Storage Base Cabinet
• Fire Proof Tiles

OIL BATH HIGH TEMPERATURE SE-137: Double walled with inside made of Heavy S.S. and outside of M.S. sheet duly powder coated. The gap etween the two walls is fitted with high grade glass wool to minimize thermal loss. Temperature range from ambient to 250C 2C, is controlled by hydraulic capillary type thermostat. A variable speed strirring arrangement is fitted to the unit for maintaining temperature Plug to work on 220230 volts A.C. supply.

Most versatile for Biochemical Oxygen Deand determinations. Castor wheel mounted cabinet is double walled with inner chamber S.S. and outer wall of M.S. Sheet duly powder coated. The gap of 75 m.m. between the outer and the inner wall is fitted with special grade glass wool to prevent thermal losses. Triple walled back of the unit is fitted with two air circulatic fans for maintaining temperature uniformity throughout the chamber, Fully view inner glass/Acralic door permits inspection of specimens, without disturbing the same. Lock and key arrangement is provided in the double walled outer door. Unit is fitted with door operated illumination lamp inside the chamber. Refrigeration unit is formed by ISI marked compressor, The front panel is provided withseparate indicator lamps for main, heating and incoming voltage. Supplied complete with 3 shelves, cord and plug to work on 220/230 A.C. supply. Temperature From 5.C to 50.c is controlled by MICRO PROCESSOR ELECTRONIC DIGITAL TEMPERATURE INDICATOR-CUM-CONTROLLER with an accuracy of 0.5C.

Outer wall is made up of M.S. sheet duly painted and inside of S.S. The gap between inner and outer wall is filled with high grade mineral glass wool. Temp. rang from ambient to 70C is controlled by JUMO / EGO GERMAN capillary type thermostat with an accuracy of 0.5 C. The unit is provided with manual tilting device, so as to tilt the tray holding the eggs. To work on 220, 230 volts A.C. supply.

CAPACITY:

50 eggs.
100 eggs.
200 eggs.
250 eggs.

It has a heavy cast iron with rugged construction and two side arms for holding flasks. Fitted with a F.H.P heavy duty motor with variable speed. Can hold flasks from 100 to 1000 ml. Capacity. Supplied with cord and plug to work on 220/230 volts A.C. supply.

• To hold 4 flasks.
• To hold 4 flasks and top platform to hold 4 flasks/bottle.
• To hold 8 flasks.
• To hold 8 flasks and top platform to hold 4 flasks/bottles.

Made out of heavy gauge S.S. with concentric rings. Auto-cut heating elements are fitted. to protect the same when bath gets dry. To work on 220/230 volts A.C. supply.

• 300 x 250 x 100 m.m. (6 Holes of 75 m.m. dia)
• 355 x 405 x 75 m.m. (12 Holes of 75 m.m. dia)

It eliminates the use of fractional weights. These units are provided with air damping device.

Model Capacity Sensitivity
SE-401 200g 1mg

It has outer wall made of M.S. Sheet duly powder coated and inner wall made up of heavy gauge S.S. Sheet. The gap between inner and outer wall is filled with high grade glass wool to avoid thermal loss. Besides outer double walled door, a full view inner glass door allows inspection of test samples without disturbing the inner chamber conditions. Unit is supplied with three adjustable perforated shelves. Temperature range from 5C to 50C 1c is controlled by DUAL SETTING Digital Temperature indicator-cum-controller so as to set two different temperatures for Day and Night. Exterior illumination with flourescent tubes fitted on both sides of the chamber accounts for artificial day light, and the cyclic illumination conditions are regulated by automatic 0-24 hrs. timer, when all the tubes are on temperature from 15C to 50C 1C can be from ambient to 50C and the same is achieved by means of injecting steam. Arrangements for increasing the humidity is provided and not for decreasing.