Sarthak Die Mould Accessories Company

Kharadi, Pune, Maharashtra

Product Features:

• Engineerd with Precision & Perfection
• Quality Excellence is Assured
• Accuracy & Precision in Dimension
• Resistance to Abrasion
• Resistance toCorrosion

Special Features

• Rugged design
• Abrasion resistance
• Longer service life

Latches are simple, low-level system lock (serialization mechanisms) that coordinate multi-user access (concurrency) to shared data structures, objects, and files. Latches protect shared memory resources from corruption when accessed by multiple processes. Specifically, latches protect data structures from the following situations:

• Concurrent modification by multiple sessions
• Being read by one session while being modified by another session
• Deallocation (aging out) of memory while being accessed

Features:

• Preventive to Rust
• Light Weight
• Quality Standards assured
• Eaxy Installation

Guide Bush is manufactured with precision and dimensional accuracies. This shows efficient guiding operation and pushes the bush radial in scroll compressors and other related products. Manufactured with optimum materials of alloys and metals, they are durable and reliable.

• d4 is the maximum diameter (i.e Collar Diameter) of Bush
• TL is the total length of Bush
• Tolerance between Pin & Bush is H7/g6
• Guide diameter tolerance for Pin & Bush to suit in the plate is k6
• Please specify the balance dimension i.e d1, d3, k etc as per requirements with necessary tolerance

Parting locks are used in moulds for pulling the plates to< a desired limit. They act like puler. The unique design and selection of the right material makes the performance of application more better.

Features:

• Place the Parting Locks Bolt on moving side of the Mold
• Install min.4 nos. on one mold, 2 nos. each on both sides of the plate
• After placement of the Parting locks on the plate, turn the bolt to 900 and plastic lock will expand
• Do not apply any lubricant on plastic part. Doing so will reduce the friction and grip
• Use h 7 reamer in hole of the mold plate with 0.1 mm range
• Mould weight < 100 kgs, use 4 nos. of 12 parting lock
• Mould weight < 500 kgs, use 4 nos. of 16 parting lock
• Mould weight < 1000 kgs, use 4 nos. of 20 parting lock
• If more load to be pulled then above limit then use more nos. Of parting locks o be used. I.e. 6 or 8 nos

Air venting system plays an important role in plastic mould, especially in high speed injection. 1. Source of the air in the plastic injection mould

• Air in gating system and mould cavity.
• Some raw materials are not dried absolutely. The air in it is gasified under high temperature.
• As the injection temperature is high, some gases are generated by the decomposition of some instable plastic.
• Some additives in raw material volatilize or occur chemical reaction, and then the gases were generated.

Application:

• For plastic injection moulding
• Applicable for thin wall products
• Pore size range from 0.05 mm to 0.1 mm in diameter
• Increased productivity through fast & easy exchange of air from venting plug
• High venting efficiency
• High thermal conductivity
• Long durability
• Corrosion resistant

• d1 Body Dia

• d2 Head Dia

• K Head Length

• L Body Length

• R Radius

• T1 Max. Dia of taper hole

• T2 Min. Dia of taper hole

• Note:

• Body Dia(d1) 0.04

• T1, T2 will be 0.2.
  
  The molten plastic injected from the injector nozzle will go through a sprue (sprue bush), a runner, and a gate and fill up in the cavity.so learn Sprue bush design is important, because sprue bush is part that contact first time with melted plastic, bad design of sprue bush can make plastic product broken, especially sprue broken and runner broken.