The pH 600 - 1 series of pH Controller and Transmitter provides a reliable method of Monitoring, Controlling & Transmitting 4 - 20mA / RS 485 MODBUS RTU communication for Interfacing to PLC, Data logger, HMI, etc., . This product is suitable to measure pH in water treatment, Electrolytic water cleaning, Chemical Industries, Food Process, Waste Water treatment, Textile Industries & Neutralization process, etc., . This pH Controller & Transmitter can Measured using Industrial Combined pH Sensors, Temperature can be measured using temperature sensor.

Features :

• Economical, Easy to Calibrate and Setup
• Wide range from -2 to 16 pH
• High Accuracy
• Programmable Auto / Manual Temperature Compensation
• Optional Isolated RS 485 communication with MODBUS RTU protocol
• Optional Galvanically Isolated 4 - 20mA Re Trans. Output
• Very High Input Impedance >10 Ohms
• User selectable Automatic and Manual calibration
• User selectable 2 or 3 point buffer calibration
• 2 Relay Outputs with Configurable individual H / L Setting with 6 relay status
• Optional audible inbuilt buzzer Output with front key reset
• Universal Supply Voltage 90 to 270V AC / DC

Specifications :

• Display 4 + 4 Digit 0.5” & 0.39” 7 Seg RED LED Display
• Input Impedance >1012 Ohms
• Range -2 to 16 pH
• Resolution 0.01 pH
• Temperature sensor RTD - PT 100 (3 wire)
• Temp. Compensation Manual / Automatic (-20.0 to +150.0ºC)
• Electrode Input Combined Electrode with BNC Attachment
• Accuracy ± 0.01 pH ± 1 digit
• Set Point - 1 & 2 Two Set Point with 6 Relay Status Selectable
• Relay Output Relay - 1 for Setpoint - 1, Relay - 2 for Setpoint - 2 with 5A Rating
• Relay Hysterisis 0 to 5 pH (user adjustable)(only for High & Low control modes)
• Relay Cyclic delay 0 to 100 seconds (user adjustable)(only for High & Low control modes)
• Alarm Output(optional) inbuilt audible buzzer with front key reset
• Optional Re. Tx. output Galvanically Isolated 4 - 20 mA
• Optional Comm. output Isolated RS 485
• Comm. Protocol MODBUS RTU
• Operating Environment -10 to 50ºC / 10 to 95 % RH Non Condensing
• Power Supply 90 to 270V AC / DC 50Hz
• Dimension 96 x 96 x 85 mm.
• Cutout Dimension 92 x 92 mm
• Weight 500 grams (Approx.)

The TDS 602 - 1 series of TDS Controller and Transmitter provides a reliable method of Monitoring, Controlling & Transmitting 4 - 20mA / RS 485 MODBUS RTU Communication for Interfacing to PLC & Data logger. This product is suitable to measure TDS in water treatment, Electrolytic water cleaning, Chemical Industries, Food Process, Waste Water treatment, Textile Industries & Neutralization process, etc., . This TDS Controller & Transmitter can Measured using Industrial TDS Sensors, Temperature can be measured using temperature sensor.

Features :

• Economical, Easy to Calibrate and Setup
• User selectable 6 ranges from 1ppm to 200ppt
• High Accuracy
• Programmable Auto / Manual Temperature Compensation
• Optional Isolated RS 485 communication with MODBUS RTU protocol
• Optional Galvanically Isolated 4 - 20mA Re Trans. Output
• Adjustable Cell Constant for particular ranges
• Manual single or 2 point Calibration
• 2 Relay Outputs with Configurable individual H / L Setting with 6 relay status
• Optional audible inbuilt buzzer Output with Front key reset
• Universal Supply Voltage 90 to 270V AC / DC

Specification :

• Display 4 + 4 Digit 0.5” & 0.39” 7 Seg RED LED Display
• Cell Constant * 0.01 / 0.1 / 1(user selectable depends on range*)
• Range(any one) 1 - 20ppm, 5 - 200ppm, 10 to 2000ppm, 1 to 20ppt, 5 to 200ppt
• Resolution 0.01ppm to 0.1ppt (depends on range)
• Temp. Compensation Manual / Automatic (-20.0 to +150.0ºC)
• Temp. Sensor RTD - PT 100 (3 wire)
• Temp. Coefficient 0 to 3 % / ºC(user adjustable)
• Electrode Input Conductivity cell on rear panel
• Accuracy ± 1 % of range ± 1 digit
• Set Point - 1 & 2 Two Set Point with 6 Relay Status Selectable
• Relay Output Relay - 1 for Setpoint - 1, Relay - 2 for Setpoint - 2 with 5A Rating
• Relay Hysterisis 0 to 500 counts (user adjustable)(only for High & Low control modes)
• Relay Cyclic delay 0 to 100 seconds (user adjustable)(only for High & Low control modes)
• Alarm Output(optional) inbuilt audible buzzer with front key reset
• Optional Re. Tx. output Galvanically Isolated 4 - 20 mA
• Optional Comm. output Isolated RS 485
• Comm. Protocol MODBUS RTU
• Operating Environment -10 to 50ºC / 10 to 95 % RH Non Condensing
• Power Supply 90 to 270V AC / DC 50Hz
• Dimension 96 x 96 x 85 mm.
• Cutout Dimension 92 x 92 mm
• Weight 500 grams (Approx.)

Features :

• 3 + 3 Digit Seven Segment LED Display
• ØSeconds, Minutes, Hours Configurable
• Selectable Resolution 0.01 / 0.1 / 1
• Relay Output with Selectable Delay Mode
• Front End Reset with Protection
• External Start / Reset Options
• 10 Years Memory Backup
• Universal Supply Voltage 90 to 270V AC / DC

Specification :

• External Input START / RESET ( potential free contact inputs)
• Range 99.9 sec / 99.9, 999 Secs / Mins / Hrs(Selectable)
• Resolution 0.01 Sec / 0.1Min/Hr
• Accuracy ± 0.05 % of FS or 50 msec
• 3 Digit 0.5” RED Seven Segment LED For PV +
• Display 3 Digit 0.39” Green Seven Segment LED For SV
• Relay Output 2 NO , 2 NC 5 A Rated Relay
• Working temperature 0 - 50 ºC
• Power Supply 90 to 270V AC / DC 50Hz
• Dimension 72 x 72 x 65 mm
• Weight 200 grams (Approx.)

SANSEL Model HCAL 1104U – v2 Humidity and Temperature Generator is to perform a rapid & easy calibration of portable instruments, sensors, Transmitter and data logger of different manufacturers. Solid state Heating & Cooling technology with high performance humidification system, generate precision chamber stability & uniformity gradient range from 5 to 60°C(Temp.) / 5 to 95 % RH*(Humd.) / -25 to 40°C(Dew point)

Features

• 7” True colour TFT display with Touch screen
• Control range from 5 to 60°C(Temp.) / 5 to 95 % RH (Humd.)/-25 to 40°C(Dew point)
• Semi Portable & Rugged
• High Resolution 0.01 °C / %RH
• Stability better than ± 0.05°C / 0.2 % RH
• Better uniformity ± 0.2°C / 0.3 % RH
• Fast raising & quick settling
• Improved design to provide better thermal performance in term of control stability & temperature gradients
• Inter changeable front door to suit different manufacturer’s indicator, sensor, transmitters

Accessories

• Basic Instrument
• External Humidifier system-weight 6kg(approx.)
• Desiccant cells – 2nos
• Molecular sieve Desiccant – 2kg
• Interchangeable Acrylic door (plain)
• Spare fuses
• Instruction manual
• Mains card
• Traceable calibration certificate

Optional

• Precision Portable Hygrometer with sensor – Model : HTD 200
• Additional Molecular sieve Desiccant
• Additional Interchangeable Acrylic door (custom special holes)
• Carrying case

SANSEL make digital ORP(Oxidation Reduction Potential)/ Redox meter is a precise and rugged instrument Carefully designed for the most accurate measurement of pH in Laboratories and industries. The instruments are completely IC version using “MOFSET” input “OP - AMP” and CMOS ICS. It is a met al cabinet of elegant shape. All the controls that are in regular use have been incorporated in the front panel for operational easy. The instrument is capable of measuring millivolts with auto. Polarity for redox potentials and potentiometric tirations. This instrument Operates from 180V to 230V AC 50Hz.

Features :

• Highly reliable and accurate meter.
• Very responsive combination glass ORP electrode.
• Latest ICs used for quick sensing and high accuracy.
• Input is compactable for any type of electrode.
• CAL adjustment controls are provided on front for recalibration of instrument.

Accessories :

• Basic Instrument
• ORP Electrode
• Electrode Clamp & stand set
• Instruction manual

Clarity of water is extremely important in products destined for human consumption. Suspension free water is also considered necessary for industries manufacturing beverage, food products etc. Similarly, minimum limits of turbidity are required to be observed in drinking water & sewage disposals. SANSEL Digital Nephelometer Model DN 1000 are ideal instruments for measurement of suspensions. They consist of a light source focused on a test tube containing the sample solution under test. The light, reflected at right angle to the focused light by the suspension in the solution, is detected by the photo electric detector, amplified and displayed on a 3½ digit LED display.

Features :

• 3 ½ digit 7 segment LED
• 2 Range Selection
• Light Emitting Diode (LED) Light Source
• Zero & SPAN Calibration From Front Panel
• Compact Size
• Power ON/OFF Indicating Switch
• 230V AC Operating Supply

Accessories :

• Basic Instrument
• Glass Test Tube – 4 nos
• Power cord
• Instruction manual

We are a leading service provider for calibration of various types of parameters in all industries and our lab is accredited by (NABL)National Accreditation Board for Testing and Calibration laboratories from Chennai, Tamil Nadu, India.

Type of Instruments CalibratedGaugesVernier CaliperExternal Micrometer
Height gaugePlunger dial guageDepth gaugeSnap gauge, etc.

Features :

• 6 Digit Seven Segment LED Display
• Wide Range 999999 Counts
• 3 to 30V DC Input Pulse from any type Sensor
• Allows Maximum 3.5 kHz Input Pulse Speed
• Low / Medium / High Speed Input Pulse selection
• Front End Reset with Protection
• External Reset Options
• 10 Years Memory Backup
• 12 V DC Sensor Supply
• Universal Supply Voltage 90 to 270V AC / DC

Specification :

• 3 - 30V DC from Proximity Sensor, Photoelectric Non Contact Sensor, Encoder,
• Potential Free Contacts, Limit Switch etc., Input
• Input Speed 3.5 kHz (Max.)
• Range 0 - 999999 counts
• Resolution 1 count /pulse
• Sensor Supply 12V DC (±10%) 50mA
• Display 6 Digit 0.5” / 0.3” seven Segment Red Led
• Working temperature 0 - 50 ºC
• Power Supply 90 to 270V AC / DC 50Hz
• Dimension 36 x 72 x 65 mm / 48 x 96 x 65 mm
• Weight 200 grams (Approx.)

Features :

• 4 Digit Seven Segment LED Display
• Wide Range 0 - 9999 RPM
• 3 to 30V DC Input Pulse from any type Sensor
• Allows Maximum 3.5 kHz Input Pulse Speed
• 12 V DC Sensor Supply
• Universal Supply Voltage 90 to 270V AC / DC

Specifications :

• Input 3 - 30V DC from Proximity Sensor, Photoelectric Non Contact Sensor, Encoder,
• Potential Free Contacts, Limit Switch etc., Input
• Input Speed 3.5 kHz (Max.)
• Range 0 - 9999 RPM
• Resolution 0.001, 0.01, 0.1, 1 RPM (Auto Ranging)
• Sensor Supply 12V DC (±10%) 50mA
• Accuracy ± 0.05 % (± 1 count)
• Display 4 Digit 0.5”seven Segment Red Led
• Working temperature 0 - 50 ºC
• Power Supply 90 to 270V AC / DC 50Hz
• Dimension 36 x 72 x 65 mm
• Weight 200 grams (Approx.)

Features :

• View the Count Display From Long Distance 3 to 30V DC Input From any type of Pulse 0/P Sensor
• 4" & 8" Available in Different Segment Sizes (1" & 2" on Request)
• Different type of Mounting Wall, Selling, Panel, "L" Clamping
• 6 Digit Seven Segment LED Display
• Wide Range 999999 Counts
• Allows Maximum 3.5 kHz Input Pulse Speed
• NPN PNP , LIMIT Switch, etc., differnet type of Input selection
• Front End Reset with Protection
• External Reset Options
• 10 Years Memory Backup
• 12 V DC Sensor Supply
• Supply Voltage 230V AC

Features :

• 16 Characters LCD Display
• mV / mA / Volt Analog Inputs
• Wide Input Ranges ± 75mV / ± 10V
• Wide Display Ranges - 199999 to +199999
• Parameter & Unit Display User Front Configurable
• 2 Relay Outputs with Configurable H / L Setting(Optional)
• Re Transmission Output (Optional)
• 24 V DC Sensor Supply
• Universal Supply Voltage 90 to 270V AC / DC

Features :

• 4 Digit Seven Segment LED Display
• Wide Range 0 - 9999 RPM / RPS / RPH
• 3 to 30V DC Input Pulse from any type Sensor
• opto isolated Re Transmission analog output 4-20mA or 0-10 V DC
• Allows Maximum 3.5 kHz Input Pulse Speed
• RPM / Rate / Frequency Front Key Scalable.
• 2 Relay Output with Front Key Set table Hi & Lo Set points
• Power ON Delay & Hysterisis for Relay Output is Provided
• 12 V DC Sensor Supply
• Universal Supply Voltage 90 to 270V AC / DC

Specification :

• Input  Input 3 - 30V DC from Proximity Sensor, Photoelectric Non Contact Sensor, Encoder,
• Potential Free Contacts, Limit Switch etc., Input Speed 3.5 kHz (Max.)
• Range 0 - 9999 RPM / RPS / RPH
• Resolution 0.001, 0.01, 0.1, 1 RPM / RPS / RPH (selectable)
• Relay Output 2 NO , 2 NC 5A Rated Relays(power ON Delay & Hysterisis provided)
• Re transmission output 4-20mA/0-10 V DC
• communication output RS 485
• Sensor Supply 12V DC (±10%) 50mA
• Accuracy ± 0.05 % (± 1 count)
• Display 4 Digit 0.5”seven Segment Red Led
• Working temperature 0 - 50 ºC
• Power Supply 90 to 270V AC / DC 50Hz
• Dimension 96 x96 x 65 mm
• Weight 200 grams (Approx.)

SANSEL offers PROCESS INDICATORs are extremely versatile Indicators that can be used for a wide variety of applications. These INSTRUMENT offer extreme reliability and low cost for Process measurement and logging. PI 542A is a Microprocessor based instrumentation ensures accurate readings for all LinearParameters. A number of programmable features including In-line calibration are standard. All the parameters are saved in a non volatile EEPROM memory which doesn't needs any external battery.PI 542A can offer relay outputs for signals exceeding set points. Programmable Re Transmission output models are also available in addition to the industry standard 4 -20mA or 0 - 10V DC output. Optional RS 485 (2 wire ) output also provided for PC communication with PC Interface software & also with MODBUS RTU protocol.

Features

• 4 Digit 7 segment RED LED display
• High Accuracy
• Compact Size
• 24 Bit ADC Resolution
• Selectable Inputs RTD , all types of thermocouples , mA, mV , Voltage , ohms.
• Wide Selectable Range between -1999 to 9999 counts
• Easy Field Configurable with Front Key Calibration
• No Hardware Selection For the Input Signals
• Optional Opto Isolated Re Transmission Output.
• Optional RS 485 (2 wire) Output for PC communication
• Optional PC software with Monitoring, Logging, Report & Graph
• Optional MODBUS RTU protocol
• 24V DC External Sensor Supply
• Programmable Decimal Point & Display Noise Filter
• Universal Supply Voltage 90 to 270 AC / DC

Specification

• Display 4 Digit 7 segment RED LED
• Analog Inputs 0 - 20 mA, 0 to 75 mV, -10 to 10 V DC, 0 - 400 Ù (H & L Limit Programmable)
• Temperature Inputs RTD - PT 100, Thermocouple - J, K, R, S, T, B, N, E
• Analog Display Range* - 1999 to 9999 (H & L Limit Programmable)
• Temperature Range RTD - PT 100 (-199.9 to 850.0°C / -199.9 to 1562°F)
• (H & L Limit Programmable) RTD - PT 1000 (-50.0 to 400.0°C / -58.0 to 752.0°F)
• TC - J (- 200.0 to 200°C / -328.0 to 2192°F)
• TC - K (- 200.0 to 1372°C / -327.8 to 2501°F)
• TC - R (- 40.0 to 1768°C / -40.0 to 3214°F)
• TC - S (- 40.0 to 1768°C / -40.0 to 3214°F)
• TC - T (- 200.0 to 400°C / -328.0 to 752°F)
• TC - B (300.0 to 1820°C / 572.0 to 3308°F)
• TC - N (-200.0 to 1300°C / -327.8 to 2372°F)
• TC - E ( -200.0 to 999.9°C / -327.8 to 1832°F)
• Unit selection °C / °F (for RTD & TC inputs)
• Analog Resolution 0.001 / 0.01 / 0.1 / 1 (Selectable)
• Temperature Resolution 0.01(for RTD-PT 100 input(°C) only) / 0.1 / 1 °C / °F
• Accuracy ± 0.1 % of FS
• Filter Constant 1 - 100 % (Adjustable)
• Relay Output**(optional) 2 Relay
• Re Transmission**(optional) Opto Isolated Analog Output 4 - 20 mA or 0 - 10V DC
• PC Communication** RS 485 (2 wire)(optional)
• PC Software**(optional) Monitoring, Data Logging, Report & Graph
• Sensor Supply(external) 24 V DC ±10% @ 100 mA
• (5A rated) with Four Relay Status Selection, Hysterisis, Cyclic Delay
• Operating Environment 0 - 50ºC / 5 to 95 % RH Non Condensing
• Power Supply 90 to 270 V AC / DC / 50 / 60 Hz
• Over All Dimension 48(H) X 96(W) X 110(D) mm
• Cut out Dimension 44(H) X 90(W) mm
• Housing Panel Mountable ABC Plastic
• Weight 250 grams (Approx.)

Fetaures

• 4 Digit Seven Segment LED Display
• Seconds, Minutes, Hours Configurable
• Selectable Resolution 0.01 / 0.1 / 1
• 2 Relay Outputs with Selectable Delay Mode
• Front End Reset with Protection
• External Start / hold / Reset Options
• 10 Years Memory Backup
• Universal Supply Voltage 90 to 270V AC / DC

Specification

• External Input START / HOLD / RESET ( potential free contact inputs)
• Weight 200 grams (Approx.)
• Dimension 72 x 72 x 110 mm
• Power Supply 90 to 270V AC / DC 50Hz
• Working temperature 0 - 50 ºC
• Relay Output 2 NO , 2 NC 5 A Rated Relay
• Display 4 Digit 0.5” Seven Segment LED RED
• Accuracy ± 0.05 Of Selected Range or 50msec (whichever Is First)
• Resolution 0.01 Sec/Min/Hr
• Range 99.59, 999.9, 9999 Secs / Mins / Hrs(Programmable)

Features

• 6 Digit Seven Segment LED Display
• Wide Range 999999 Counts
• 3 to 30V DC Input Pulse from any type Sensor
• Allows Maximum 3.5 kHz Input Pulse Speed
• Low / Medium / High Speed Input Pulse selection
• 2 Relay Output with Front Key Set table 2 High Set points
• Front End Reset with Protection
• Cumulative Count Display
• 10 Years Memory Backup
• 12 V DC Sensor Supply
• Universal Supply Voltage 90 to 270V AC / DC

Specification

• 3 - 30V DC from Proximity Sensor, Photoelectric Non Contact Sensor, Encoder,
• Potential Free Contacts, Limit Switch etc., Input
• Input Speed 3.5 kHz (Max.)
• Range 0 - 999999 counts
• Resolution 1 count /pulse
• Relay Output 2 NO , 2 NC 5 A Rated Relays
• Sensor Supply 12V DC (±10%) 50mA
• Display 6 Digit 0.39”seven Segment Red Led
• Working temperature 0 - 50 ºC
• Power Supply 90 to 270V AC / DC 50Hz
• Dimension 72 x 72 x 65 mm
• Weight 200 grams (Approx.)

Features :

• 4 Digit Seven Segment LED Display
• Wide Range 0 - 9999 RPM / RPS / RPH
• 3 to 30V DC Input Pulse from any type Sensor
• Allows Maximum 3.5 kHz Input Pulse Speed
• RPM / Rate / Frequency Front Key Scalable.
• 2 Relay Output with Front Key Set table Hi & Lo Set points
• Power ON Delay & Hysterisis for Relay Output is Provided
• 12 V DC Sensor Supply
• Universal Supply Voltage 90 to 270V AC / DC

Specifications

• Input 3 - 30V DC from Proximity Sensor, Photoelectric Non Contact Sensor, Encoder,
• Potential Free Contacts, Limit Switch etc., Input
• Input Speed 3.5 kHz (Max.)
• Range 0 - 9999 RPM / RPS / RPH
• Resolution 0.001, 0.01, 0.1, 1 RPM / RPS / RPH (selectable)
• Relay Output 2 NO , 2 NC 5A Rated Relays(power ON Delay & Hysterisis provided)
• Sensor Supply 12V DC (±10%) 50mA
• Accuracy ± 0.05 % (± 1 count)
• Display 4 Digit 0.5”seven Segment Red Led
• Working temperature 0 - 50 ºC
• Power Supply 90 to 270V AC / DC 50Hz
• Dimension 72 x 72 x 65 mm
• Weight 200 grams (Approx.)

SANSEL Model TCAL 1402 / -20 Miniature calibrator bath are one of the smallest dry well calibrator in the world, which are ideally suited were necessary for fast calibration in process industries to calibrate Thermocouple, RTD, Indicator with sensor & transmitter with sensor. Temperature range of the TCAL 1402 / -20 covers from -15°C* to 75°C. These equipment are light weight, fast raising, quick settling, better stability & uniformity. TCAL 1402 / -20 Miniature calibrator bath’s temperature are adjusted simply using 4 keys on the controller, can be very quickly controlled the actual and set temperature can be displayed simultaneously on a 4+4 digit high brightness LCD. TCAL 1402 / -20 having interchangeable inserts to suit for calibration of different diameter of sensors (upto 16mm). Additional Inserts(optional) with special drillings are available to order.

Features :

• Wide temperature range -15* to 75°C
• Light weight - Less than 8 kg (Approx.)
• World class performance
• Fast calibration save time & money
• Simple, Convenient & easy operation
• High Bright LCD Display
• Rugged & most compact for onsite carry
• Inter changeable insert to suit different diameter sensor
• Supplied with rexein carry bag
• ISO / IEC 17025 Standard Accredited Calibration Certificate

Accessories

• Basic Instrument
• Standard well insert
• Well tool
• Spare fuses
• Instruction manual
• Mains card
• Carry bag
• Traceable calibration certificate

Optional

• Master Indicator with sensor
• Additional well insert
• Carrying case

SANSEL Model TCAL 1402 / 500 Miniature calibrator bath are one of the smallest dry well calibrator in the world, which are ideally suited were necessary for fast calibration in process industries to calibrate Thermocouple, RTD, Indicator with sensor & transmitter with sensor. Temperature range of the TCAL 1402 / 500 covers from Ambient + 5°C to 500°C. These equipment are light weight, fast raising, quick settling, better stability & uniformity. TCAL 1402 / 500 Miniature calibrator bath’s temperature are adjusted simply using 4 keys on the controller, can be very quickly controlled the actual and set temperature can be displayed simultaneously on a 4+4 digit high brightness LCD. TCAL 1402 / 500 having interchangeable inserts to suit for calibration of different diameter of sensors (upto 20mm). Additional Inserts(optional) with special drillings are available to order.

Features :

• Wide temperature range Amb.+5 to 500°C
• Light weight - Less than 2 kg (Approx.)
• World class performance
• Fast calibration save time & money
• Simple, Convenient & easy operation
• High Bright LCD Display
• Rugged & most compact for onsite carry
• Inter changeable insert to suit different diameter sensor
• Supplied with rexein carry bag
• ISO / IEC 17025 Standard Accredited Calibration Certificate

Accessories

• Basic Instrument
• Standard well insert
• Well tool
• Spare fuses
• Instruction manual
• Mains card
• Carry bag
• Traceable calibration certificate

Optional

• Master Indicator with sensor
• Additional well insert
• Carrying case

These are Master Thermocouple without Cold Junction. This range is based on popular Standard Thermocouple range, Sensitivity & Length.
MTC are highly accurate and stable Thermocouple with minimum uncertainties. It offer wide temperature range which is ideal for all industrial applications. The size, length and Thermocouple Material are such that give the best and most stable results.

Features :

• Temperature range upto 1200 & 1500 deg C
• 6mm O.D & available different Dimensions
• Outer Sheath SS 316 / Inconel / High Alumina Tube
• High Accuracy & Stability
• Manufactured & Tested under strict quality control standards
• Cycled to Stability
• Fast Response
• Low Drift

SANSEL Model TCAL 1401 / -30 Dry well Temperature calibrator are high performance for industrial atmosphere and covering temperature range from -30* to 100°C. Which are ideally suited onsite calibration of thermocouple, RTDs, Indicator with sensors & 4-20mA signal transmitter with indicator in Food, Pharmaceutical and all types of process industries. Having it’s advantage of user friendly, light weight, portable, fast settling, better uniformity and accuracy over a wide temperature range. TCAL 1401 / -30 having interchangeable inserts to suit for calibration of different diameter of sensors (upto 16mm). Additional Inserts(optional) with special drillings are available to order.

Features :

• High Bright 4 + 4 digit 7 seg LCD Display with 4 keys
• Portable & Rugged
• Range from -30* to 100°C
• No Liquids, Safe dry Calibration
• Micro Controller Based Linearized High Accuracy
• Stable to ± 0.1°C
• Axial + Radial uniformity - better than ± 0.15°C
• Inter changeable insert to suit different diameter sensor - up to 22 mm
• ISO / IEC 17025 Standard Accredited Calibration Certificate

Accessories

• Basic Instrument
• Standard well insert
• Well tool
• Spare fuses
• Instruction manual
• Mains card
• Carry bag
• Traceable calibration certificate

Optional

• Master Indicator with sensor
• Additional well insert
• Carrying case

Features :

•  Large 2.8" TFT display with Touch screen
•  Ranges from -40 to 85 DegC / 0 to 100% RH / psychometric Converted Dew point
•  More resolution 0.01 DegC / 0.01 % RH
•  High Accuracy : ±0.2 DegC / ±0.8 % RH
•  Inbuilt rechargeable polymer Li-ion battery
•  Alarm facility
•  Comfortable and anti-slip grip
•  Portable & Rugged with carrying case
•  ISO/IEC 17025 Accredited Calibration certificate
• Optional High temperature sensors available on request for temperature ranges -50 to 100 DegC & -100 to 200 DegC

SSPRT is Highly Accurate Platinum Resistance Thermometer(PT 100) offer the temperature range of - 80 to 660ºC. SSPRT gives the benefit of high accuracy and low drift in a solid metal case. Wire wound resistance element give good stability with low temperature coefficient and high accuracy.
SSPRT is constructed with a 6 mm outer diameter of Inconel sheath of high durability. SSPRT is available in different accuracies and length. A special powder mixture is filled into the sensor capsule to support the element from mechanical shocks.

Features :

• Temperature range from -80 to 660 deg C
• 6mm O.D & available different Dimensions
• Outer Sheath SS 316 / Inconel / High Alumina Tube
• High Accuracy & Stability
• Manufactured & Tested under strict quality control standards
• Cycled to Stability
• Fast Response
• Low Drift

Specifications :

• Type PT 100 (four wire)
• Temperature Range -80 to 660
• Element PT 100
• Accuracy * Class A, 1/3, 1/5, 1/10 DIN
• Sheath Diameter 6mm
• Sheath Length 300mm, 450mm, 600mm
• Cable Length 1000mm or as Required
• Outer Sheath SS-316
• End Connection Flying Lead

Features :

• View the Count Display From Long Distance 4" , 8" Available in Different Segment Sizes (1" & 2" on Request)
• Different type of Mounting Wall, Selling, Panel, "L" Clamping
• 4 Digit Seven Segment LED Display • Seconds, Minutes, Hours Configurable
• Selectable Resolution 0.01 / 0.1 / 1
• 2 Relay Outputs with Selectable Delay Mode
• Front End Reset with Protection
• External Start / hold / Reset Options
• 10 Years Memory Backup )
• Supply Voltage 230V AC

We are a leading service provider for calibration of various types of parameters in all industries and our lab is accredited by (NABL)national accreditation board for testing and calibration laboratories from Chennai, Tamil Nadu, India.

Very Low Pressure ± 25 mbar
Type of Instruments CalibratedManometerLow pressure Transducer/TransmitterGaugesDifferential Pressure Indicator/TranmitterPressure Data LoggerPressure switchLow pressure Calibrators, etc.,

Absolute Pressure: 0.60 bar to 2 bar
Type of Instruments CalibratedBarometersAneroid barometerAbsolute gaugesAbsolute pressure sensor/TranmitterAbsolute pressure indicator/ controllerLogger and Calibrators etc

Vacuum: -0.1 bar to -0.99 bar
Type of Instruments CalibratedVacuum GaugeVacuum Tranduer/TransmitterVacuum Indicator/Controller/SwitchVacuum LoggerCalibrators etc.,

Pressure(Hydraulic and Pneumatic) 1 bar to 1000 bar and 0.1 bar to 35 bar
Type of Instruments CalibratedPressure CalibratorsPressure TransducerPressure TransmitterDigital Pressure GaugesPressure ControllerPnueumatic pressure gaugesHydraulic Pressure gaugesDifferential pressure indicators, etc.,

Mass/Weight 1 mg to 50 kg
Type of Instruments Calibrated(Accuracy class: E2, F1, F2, M1, M2, ETC., )Standard weight boxWeights, etc., Weighing Scale and Balance 1mg to 300 KgMicro balanceAnalytical balanceDigital balanceWeighing Scale

Volume 1µl to 5l
Type of Instruments CalibratedPipetteBuretteFlaskbeakerAll types of measuring cylinder

Acoustic Pressure : Range 94 & 114 DB
Type of instruments Calibratedsound level meter, etc., Contact RPM/Tachometer: 100 RPM to 10000 RPMNon - Contact RPM/Tachometer: 12 RPM to 99950 RPMType of Instruments CalibartedContact & Non contact type RPM IndicatorContact & Non contact type TachometerCentrifugal, etc., Dimensional(Basic Instrument, Gauge, etc., )Vernier CalipersExternal MicrometerPlunger Dail GaugeLever Type DailBore GaugeHeight GaugesDepth MicrometerDepth GaugesThickness GaugesSnap GaugeFeeler gaugeInternal Micrometerwidth GaugeDial Caliper GaugeMicrometer SettingPlain Plug GaugePistol CaliperThread Measuring WiresMeasuring Pin

We are a leading service provider for calibration of various types of parameters in all industries and our lab is accredited by (NABL)National Accreditation Board for Testing and Calibration laboratories from Chennai, Tamil Nadu, India.

Temperature(Contact) Range from -80 deg C to 1500 deg c

Type of Instruments Calibrated:Digital ThermometerGlass ThermometerDry block Calibrators
Thermocouple and RTD probesThermistorsTemperature RecorderTemperature Scanner/Data loggerTemperature Indicator with sensorTemperature GaugeTemperature TransmitterTemperature bath, etc., Mapping and Validation for single or multi pointFreezerincubatorovenfurnanceStorage roomsclean roomsdryercold roomsEnvironmental chambersHumidity Indicator/chamber, etc., Temperature(Non-Contact)Range from 0 deg c to 1500 deg c

Type of Instruments Calibrated
Non-Contact PyrometersIR thermometerBlack Body Source, ect., Humidity: Range from 5 to 60 deg c & 10 to 95%

Type of Instruments CalibratedHumidity sensors/TransmitterHumidity/Temperature loggerAnalog hygrometerdigital thermal hygrometerThermo hygro graphHumidity chamber etc., Note: Price May vary based on quantity and instruments

The pH 600 - 1 series of pH Controller and Transmitter provides a reliable method of Monitoring, Controlling & Transmitting 4 - 20mA / RS 485 MODBUS RTU communication for Interfacing to PLC, Data logger, HMI, etc., . This product is suitable to measure pH in water treatment, Electrolytic water cleaning, Chemical Industries, Food Process, Waste Water treatment, Textile Industries & Neutralization process, etc., . This pH Controller & Transmitter can Measured using Industrial Combined pH Sensors, Temperature can be measured using temperature sensor.

Features :

• Economical, Easy to Calibrate and Setup
• Wide range from -2 to 16 pH
• High Accuracy
• Programmable Auto / Manual Temperature Compensation
• Optional Isolated RS 485 communication with MODBUS RTU protocol
• Optional Galvanically Isolated 4 - 20mA Re Trans. Output
• Very High Input Impedance >10 Ohms
• User selectable Automatic and Manual calibration
• User selectable 2 or 3 point buffer calibration
• 2 Relay Outputs with Configurable individual H / L Setting with 6 relay status
• Optional audible inbuilt buzzer Output with front key reset
• Universal Supply Voltage 90 to 270V AC / DC

Specifications :

• Display 4 + 4 Digit 0.5” & 0.39” 7 Seg RED LED Display
• Input Impedance >1012 Ohms
• Range -2 to 16 pH
• Resolution 0.01 pH
• Temperature sensor RTD - PT 100 (3 wire)
• Temp. Compensation Manual / Automatic (-20.0 to +150.0ºC)
• Electrode Input Combined Electrode with BNC Attachment
• Accuracy ± 0.01 pH ± 1 digit
• Set Point - 1 & 2 Two Set Point with 6 Relay Status Selectable
• Relay Output Relay - 1 for Setpoint - 1, Relay - 2 for Setpoint - 2 with 5A Rating
• Relay Hysterisis 0 to 5 pH (user adjustable)(only for High & Low control modes)
• Relay Cyclic delay 0 to 100 seconds (user adjustable)(only for High & Low control modes)
• Alarm Output(optional) inbuilt audible buzzer with front key reset
• Optional Re. Tx. output Galvanically Isolated 4 - 20 mA
• Optional Comm. output Isolated RS 485
• Comm. Protocol MODBUS RTU
• Operating Environment -10 to 50ºC / 10 to 95 % RH Non Condensing
• Power Supply 90 to 270V AC / DC 50Hz
• Dimension 96 x 96 x 85 mm.
• Cutout Dimension 92 x 92 mm
• Weight 500 grams (Approx.)

The TDS 602 - 1 series of TDS Controller and Transmitter provides a reliable method of Monitoring, Controlling & Transmitting 4 - 20mA / RS 485 MODBUS RTU Communication for Interfacing to PLC & Data logger. This product is suitable to measure TDS in water treatment, Electrolytic water cleaning, Chemical Industries, Food Process, Waste Water treatment, Textile Industries & Neutralization process, etc., . This TDS Controller & Transmitter can Measured using Industrial TDS Sensors, Temperature can be measured using temperature sensor.

Features :

• Economical, Easy to Calibrate and Setup
• User selectable 6 ranges from 1ppm to 200ppt
• High Accuracy
• Programmable Auto / Manual Temperature Compensation
• Optional Isolated RS 485 communication with MODBUS RTU protocol
• Optional Galvanically Isolated 4 - 20mA Re Trans. Output
• Adjustable Cell Constant for particular ranges
• Manual single or 2 point Calibration
• 2 Relay Outputs with Configurable individual H / L Setting with 6 relay status
• Optional audible inbuilt buzzer Output with Front key reset
• Universal Supply Voltage 90 to 270V AC / DC

Specification :

• Display 4 + 4 Digit 0.5” & 0.39” 7 Seg RED LED Display
• Cell Constant * 0.01 / 0.1 / 1(user selectable depends on range*)
• Range(any one) 1 - 20ppm, 5 - 200ppm, 10 to 2000ppm, 1 to 20ppt, 5 to 200ppt
• Resolution 0.01ppm to 0.1ppt (depends on range)
• Temp. Compensation Manual / Automatic (-20.0 to +150.0ºC)
• Temp. Sensor RTD - PT 100 (3 wire)
• Temp. Coefficient 0 to 3 % / ºC(user adjustable)
• Electrode Input Conductivity cell on rear panel
• Accuracy ± 1 % of range ± 1 digit
• Set Point - 1 & 2 Two Set Point with 6 Relay Status Selectable
• Relay Output Relay - 1 for Setpoint - 1, Relay - 2 for Setpoint - 2 with 5A Rating
• Relay Hysterisis 0 to 500 counts (user adjustable)(only for High & Low control modes)
• Relay Cyclic delay 0 to 100 seconds (user adjustable)(only for High & Low control modes)
• Alarm Output(optional) inbuilt audible buzzer with front key reset
• Optional Re. Tx. output Galvanically Isolated 4 - 20 mA
• Optional Comm. output Isolated RS 485
• Comm. Protocol MODBUS RTU
• Operating Environment -10 to 50ºC / 10 to 95 % RH Non Condensing
• Power Supply 90 to 270V AC / DC 50Hz
• Dimension 96 x 96 x 85 mm.
• Cutout Dimension 92 x 92 mm
• Weight 500 grams (Approx.)

Features :

• 3 + 3 Digit Seven Segment LED Display
• ØSeconds, Minutes, Hours Configurable
• Selectable Resolution 0.01 / 0.1 / 1
• Relay Output with Selectable Delay Mode
• Front End Reset with Protection
• External Start / Reset Options
• 10 Years Memory Backup
• Universal Supply Voltage 90 to 270V AC / DC

Specification :

• External Input START / RESET ( potential free contact inputs)
• Range 99.9 sec / 99.9, 999 Secs / Mins / Hrs(Selectable)
• Resolution 0.01 Sec / 0.1Min/Hr
• Accuracy ± 0.05 % of FS or 50 msec
• 3 Digit 0.5” RED Seven Segment LED For PV +
• Display 3 Digit 0.39” Green Seven Segment LED For SV
• Relay Output 2 NO , 2 NC 5 A Rated Relay
• Working temperature 0 - 50 ºC
• Power Supply 90 to 270V AC / DC 50Hz
• Dimension 72 x 72 x 65 mm
• Weight 200 grams (Approx.)

SANSEL Model HCAL 1104U – v2 Humidity and Temperature Generator is to perform a rapid & easy calibration of portable instruments, sensors, Transmitter and data logger of different manufacturers. Solid state Heating & Cooling technology with high performance humidification system, generate precision chamber stability & uniformity gradient range from 5 to 60°C(Temp.) / 5 to 95 % RH*(Humd.) / -25 to 40°C(Dew point)

Features

• 7” True colour TFT display with Touch screen
• Control range from 5 to 60°C(Temp.) / 5 to 95 % RH (Humd.)/-25 to 40°C(Dew point)
• Semi Portable & Rugged
• High Resolution 0.01 °C / %RH
• Stability better than ± 0.05°C / 0.2 % RH
• Better uniformity ± 0.2°C / 0.3 % RH
• Fast raising & quick settling
• Improved design to provide better thermal performance in term of control stability & temperature gradients
• Inter changeable front door to suit different manufacturer’s indicator, sensor, transmitters

Accessories

• Basic Instrument
• External Humidifier system-weight 6kg(approx.)
• Desiccant cells – 2nos
• Molecular sieve Desiccant – 2kg
• Interchangeable Acrylic door (plain)
• Spare fuses
• Instruction manual
• Mains card
• Traceable calibration certificate

Optional

• Precision Portable Hygrometer with sensor – Model : HTD 200
• Additional Molecular sieve Desiccant
• Additional Interchangeable Acrylic door (custom special holes)
• Carrying case

A large number of salts such as carbonates, bicarbonates, chloride, sulphates, phosphates & nitrates of calcium, magnesium, sodium, potassium, iron and manganese etc., are found dissolved in natural water. Similarly coastal marine water contains substantial quantity of these salts. A high content of dissolved solids elevates the density of water, influences Osmoregulation of fresh water organism and reduces solubility of gases thereby reducing the utility of water for drinking, irrigation and industrial purposes. Therefore, determination of Total Dissolved solids is one of the important parameters in water analysis. SANSEL make digital TDS meter TDS 100 is extremely useful for fast and accurate determination of Total Dissolved Solids in a liquid. The use of solid state technology and IC circuitry makes this instrument versatile and reliable. The multi position selector switch quickly sets the digital display to the desired test range. The instrument is ideal for testing of natural water, drinking water, waste water, brine solution, sea water and soluble salts, etc.,

Features :

• Highly reliable and accurate meter.
• Very responsive Platinum Conductivity cell.
• Latest ICs used for quick sensing and high accuracy.
• Input is compactable for any type of electrode(1.0 cell constant).
• Cell adjustment controls are provided on front of instrument.
• Check adjustment controls are provided on rear of instrument

Accessories :

• Basic Instrument
• Platinum Conductivity Cell
• Electrode Clamp & stand set
• Instruction manual

Optional

• Imported certified Standard Solution (Extra charge)

SANSEL make digital Conductivity(EC) meter DCM 200 is extremely useful for fast and accurate determination of Conductivity in a liquid. The use of solid state technology and IC circuitry makes this instrument versatile and reliable. The multi position selector switch quickly sets the digital display to the desired test range. The instrument is ideal for testing of natural water, drinking water, waste water, brine solution, sea water and soluble salts, etc.,

Features :

• Highly reliable and accurate meter.
• Very responsive Platinum Conductivity cell.
• Latest ICs used for quick sensing and high accuracy.
• Input is compactable for any type of electrode(1.0 cell constant).
• Cell adjustment controls are provided on front of instrument.
• Check adjustment controls are provided on rear of instrument.

Accessories :

• Basic Instrument
• Platinum Conductivity Cell
• Electrode Clamp & stand set
• Instruction manual

Optional

• Imported certified Standard Solution (Extra charge)

SANSEL make digital ORP(Oxidation Reduction Potential)/ Redox meter is a precise and rugged instrument Carefully designed for the most accurate measurement of pH in Laboratories and industries. The instruments are completely IC version using “MOFSET” input “OP - AMP” and CMOS ICS. It is a met al cabinet of elegant shape. All the controls that are in regular use have been incorporated in the front panel for operational easy. The instrument is capable of measuring millivolts with auto. Polarity for redox potentials and potentiometric tirations. This instrument Operates from 180V to 230V AC 50Hz.

Features :

• Highly reliable and accurate meter.
• Very responsive combination glass ORP electrode.
• Latest ICs used for quick sensing and high accuracy.
• Input is compactable for any type of electrode.
• CAL adjustment controls are provided on front for recalibration of instrument.

Accessories :

• Basic Instrument
• ORP Electrode
• Electrode Clamp & stand set
• Instruction manual

Clarity of water is extremely important in products destined for human consumption. Suspension free water is also considered necessary for industries manufacturing beverage, food products etc. Similarly, minimum limits of turbidity are required to be observed in drinking water & sewage disposals. SANSEL Digital Nephelometer Model DN 1000 are ideal instruments for measurement of suspensions. They consist of a light source focused on a test tube containing the sample solution under test. The light, reflected at right angle to the focused light by the suspension in the solution, is detected by the photo electric detector, amplified and displayed on a 3½ digit LED display.

Features :

• 3 ½ digit 7 segment LED
• 2 Range Selection
• Light Emitting Diode (LED) Light Source
• Zero & SPAN Calibration From Front Panel
• Compact Size
• Power ON/OFF Indicating Switch
• 230V AC Operating Supply

Accessories :

• Basic Instrument
• Glass Test Tube – 4 nos
• Power cord
• Instruction manual

We are a leading service provider for calibration of various types of parameters in all industries and our lab is accredited by (NABL)National Accreditation Board for Testing and Calibration laboratories from Chennai, Tamil Nadu, India.

Type of Instruments CalibratedGaugesVernier CaliperExternal Micrometer
Height gaugePlunger dial guageDepth gaugeSnap gauge, etc.

Features :

• 6 Digit Seven Segment LED Display
• Wide Range 999999 Counts
• 3 to 30V DC Input Pulse from any type Sensor
• Allows Maximum 3.5 kHz Input Pulse Speed
• Low / Medium / High Speed Input Pulse selection
• Front End Reset with Protection
• External Reset Options
• 10 Years Memory Backup
• 12 V DC Sensor Supply
• Universal Supply Voltage 90 to 270V AC / DC

Specification :

• 3 - 30V DC from Proximity Sensor, Photoelectric Non Contact Sensor, Encoder,
• Potential Free Contacts, Limit Switch etc., Input
• Input Speed 3.5 kHz (Max.)
• Range 0 - 999999 counts
• Resolution 1 count /pulse
• Sensor Supply 12V DC (±10%) 50mA
• Display 6 Digit 0.5” / 0.3” seven Segment Red Led
• Working temperature 0 - 50 ºC
• Power Supply 90 to 270V AC / DC 50Hz
• Dimension 36 x 72 x 65 mm / 48 x 96 x 65 mm
• Weight 200 grams (Approx.)

Features :

• 4 Digit Seven Segment LED Display
• Wide Range 0 - 9999 RPM
• 3 to 30V DC Input Pulse from any type Sensor
• Allows Maximum 3.5 kHz Input Pulse Speed
• 12 V DC Sensor Supply
• Universal Supply Voltage 90 to 270V AC / DC

Specifications :

• Input 3 - 30V DC from Proximity Sensor, Photoelectric Non Contact Sensor, Encoder,
• Potential Free Contacts, Limit Switch etc., Input
• Input Speed 3.5 kHz (Max.)
• Range 0 - 9999 RPM
• Resolution 0.001, 0.01, 0.1, 1 RPM (Auto Ranging)
• Sensor Supply 12V DC (±10%) 50mA
• Accuracy ± 0.05 % (± 1 count)
• Display 4 Digit 0.5”seven Segment Red Led
• Working temperature 0 - 50 ºC
• Power Supply 90 to 270V AC / DC 50Hz
• Dimension 36 x 72 x 65 mm
• Weight 200 grams (Approx.)

Features :

• View the Count Display From Long Distance 3 to 30V DC Input From any type of Pulse 0/P Sensor
• 4" & 8" Available in Different Segment Sizes (1" & 2" on Request)
• Different type of Mounting Wall, Selling, Panel, "L" Clamping
• 6 Digit Seven Segment LED Display
• Wide Range 999999 Counts
• Allows Maximum 3.5 kHz Input Pulse Speed
• NPN PNP , LIMIT Switch, etc., differnet type of Input selection
• Front End Reset with Protection
• External Reset Options
• 10 Years Memory Backup
• 12 V DC Sensor Supply
• Supply Voltage 230V AC

Features :

• 16 Characters LCD Display
• mV / mA / Volt Analog Inputs
• Wide Input Ranges ± 75mV / ± 10V
• Wide Display Ranges - 199999 to +199999
• Parameter & Unit Display User Front Configurable
• 2 Relay Outputs with Configurable H / L Setting(Optional)
• Re Transmission Output (Optional)
• 24 V DC Sensor Supply
• Universal Supply Voltage 90 to 270V AC / DC

Features :

• 4 Digit Seven Segment LED Display
• Wide Range 0 - 9999 RPM / RPS / RPH
• 3 to 30V DC Input Pulse from any type Sensor
• opto isolated Re Transmission analog output 4-20mA or 0-10 V DC
• Allows Maximum 3.5 kHz Input Pulse Speed
• RPM / Rate / Frequency Front Key Scalable.
• 2 Relay Output with Front Key Set table Hi & Lo Set points
• Power ON Delay & Hysterisis for Relay Output is Provided
• 12 V DC Sensor Supply
• Universal Supply Voltage 90 to 270V AC / DC

Specification :

• Input  Input 3 - 30V DC from Proximity Sensor, Photoelectric Non Contact Sensor, Encoder,
• Potential Free Contacts, Limit Switch etc., Input Speed 3.5 kHz (Max.)
• Range 0 - 9999 RPM / RPS / RPH
• Resolution 0.001, 0.01, 0.1, 1 RPM / RPS / RPH (selectable)
• Relay Output 2 NO , 2 NC 5A Rated Relays(power ON Delay & Hysterisis provided)
• Re transmission output 4-20mA/0-10 V DC
• communication output RS 485
• Sensor Supply 12V DC (±10%) 50mA
• Accuracy ± 0.05 % (± 1 count)
• Display 4 Digit 0.5”seven Segment Red Led
• Working temperature 0 - 50 ºC
• Power Supply 90 to 270V AC / DC 50Hz
• Dimension 96 x96 x 65 mm
• Weight 200 grams (Approx.)

SANSEL offers PROCESS INDICATORs are extremely versatile Indicators that can be used for a wide variety of applications. These INSTRUMENT offer extreme reliability and low cost for Process measurement and logging. PI 542A is a Microprocessor based instrumentation ensures accurate readings for all LinearParameters. A number of programmable features including In-line calibration are standard. All the parameters are saved in a non volatile EEPROM memory which doesn't needs any external battery.PI 542A can offer relay outputs for signals exceeding set points. Programmable Re Transmission output models are also available in addition to the industry standard 4 -20mA or 0 - 10V DC output. Optional RS 485 (2 wire ) output also provided for PC communication with PC Interface software & also with MODBUS RTU protocol.

Features

• 4 Digit 7 segment RED LED display
• High Accuracy
• Compact Size
• 24 Bit ADC Resolution
• Selectable Inputs RTD , all types of thermocouples , mA, mV , Voltage , ohms.
• Wide Selectable Range between -1999 to 9999 counts
• Easy Field Configurable with Front Key Calibration
• No Hardware Selection For the Input Signals
• Optional Opto Isolated Re Transmission Output.
• Optional RS 485 (2 wire) Output for PC communication
• Optional PC software with Monitoring, Logging, Report & Graph
• Optional MODBUS RTU protocol
• 24V DC External Sensor Supply
• Programmable Decimal Point & Display Noise Filter
• Universal Supply Voltage 90 to 270 AC / DC

Specification

• Display 4 Digit 7 segment RED LED
• Analog Inputs 0 - 20 mA, 0 to 75 mV, -10 to 10 V DC, 0 - 400 Ù (H & L Limit Programmable)
• Temperature Inputs RTD - PT 100, Thermocouple - J, K, R, S, T, B, N, E
• Analog Display Range* - 1999 to 9999 (H & L Limit Programmable)
• Temperature Range RTD - PT 100 (-199.9 to 850.0°C / -199.9 to 1562°F)
• (H & L Limit Programmable) RTD - PT 1000 (-50.0 to 400.0°C / -58.0 to 752.0°F)
• TC - J (- 200.0 to 200°C / -328.0 to 2192°F)
• TC - K (- 200.0 to 1372°C / -327.8 to 2501°F)
• TC - R (- 40.0 to 1768°C / -40.0 to 3214°F)
• TC - S (- 40.0 to 1768°C / -40.0 to 3214°F)
• TC - T (- 200.0 to 400°C / -328.0 to 752°F)
• TC - B (300.0 to 1820°C / 572.0 to 3308°F)
• TC - N (-200.0 to 1300°C / -327.8 to 2372°F)
• TC - E ( -200.0 to 999.9°C / -327.8 to 1832°F)
• Unit selection °C / °F (for RTD & TC inputs)
• Analog Resolution 0.001 / 0.01 / 0.1 / 1 (Selectable)
• Temperature Resolution 0.01(for RTD-PT 100 input(°C) only) / 0.1 / 1 °C / °F
• Accuracy ± 0.1 % of FS
• Filter Constant 1 - 100 % (Adjustable)
• Relay Output**(optional) 2 Relay
• Re Transmission**(optional) Opto Isolated Analog Output 4 - 20 mA or 0 - 10V DC
• PC Communication** RS 485 (2 wire)(optional)
• PC Software**(optional) Monitoring, Data Logging, Report & Graph
• Sensor Supply(external) 24 V DC ±10% @ 100 mA
• (5A rated) with Four Relay Status Selection, Hysterisis, Cyclic Delay
• Operating Environment 0 - 50ºC / 5 to 95 % RH Non Condensing
• Power Supply 90 to 270 V AC / DC / 50 / 60 Hz
• Over All Dimension 48(H) X 96(W) X 110(D) mm
• Cut out Dimension 44(H) X 90(W) mm
• Housing Panel Mountable ABC Plastic
• Weight 250 grams (Approx.)

Fetaures

• 4 Digit Seven Segment LED Display
• Seconds, Minutes, Hours Configurable
• Selectable Resolution 0.01 / 0.1 / 1
• 2 Relay Outputs with Selectable Delay Mode
• Front End Reset with Protection
• External Start / hold / Reset Options
• 10 Years Memory Backup
• Universal Supply Voltage 90 to 270V AC / DC

Specification

• External Input START / HOLD / RESET ( potential free contact inputs)
• Weight 200 grams (Approx.)
• Dimension 72 x 72 x 110 mm
• Power Supply 90 to 270V AC / DC 50Hz
• Working temperature 0 - 50 ºC
• Relay Output 2 NO , 2 NC 5 A Rated Relay
• Display 4 Digit 0.5” Seven Segment LED RED
• Accuracy ± 0.05 Of Selected Range or 50msec (whichever Is First)
• Resolution 0.01 Sec/Min/Hr
• Range 99.59, 999.9, 9999 Secs / Mins / Hrs(Programmable)

Features

• 6 Digit Seven Segment LED Display
• Wide Range 999999 Counts
• 3 to 30V DC Input Pulse from any type Sensor
• Allows Maximum 3.5 kHz Input Pulse Speed
• Low / Medium / High Speed Input Pulse selection
• 2 Relay Output with Front Key Set table 2 High Set points
• Front End Reset with Protection
• Cumulative Count Display
• 10 Years Memory Backup
• 12 V DC Sensor Supply
• Universal Supply Voltage 90 to 270V AC / DC

Specification

• 3 - 30V DC from Proximity Sensor, Photoelectric Non Contact Sensor, Encoder,
• Potential Free Contacts, Limit Switch etc., Input
• Input Speed 3.5 kHz (Max.)
• Range 0 - 999999 counts
• Resolution 1 count /pulse
• Relay Output 2 NO , 2 NC 5 A Rated Relays
• Sensor Supply 12V DC (±10%) 50mA
• Display 6 Digit 0.39”seven Segment Red Led
• Working temperature 0 - 50 ºC
• Power Supply 90 to 270V AC / DC 50Hz
• Dimension 72 x 72 x 65 mm
• Weight 200 grams (Approx.)

Features :

• 4 Digit Seven Segment LED Display
• Wide Range 0 - 9999 RPM / RPS / RPH
• 3 to 30V DC Input Pulse from any type Sensor
• Allows Maximum 3.5 kHz Input Pulse Speed
• RPM / Rate / Frequency Front Key Scalable.
• 2 Relay Output with Front Key Set table Hi & Lo Set points
• Power ON Delay & Hysterisis for Relay Output is Provided
• 12 V DC Sensor Supply
• Universal Supply Voltage 90 to 270V AC / DC

Specifications

• Input 3 - 30V DC from Proximity Sensor, Photoelectric Non Contact Sensor, Encoder,
• Potential Free Contacts, Limit Switch etc., Input
• Input Speed 3.5 kHz (Max.)
• Range 0 - 9999 RPM / RPS / RPH
• Resolution 0.001, 0.01, 0.1, 1 RPM / RPS / RPH (selectable)
• Relay Output 2 NO , 2 NC 5A Rated Relays(power ON Delay & Hysterisis provided)
• Sensor Supply 12V DC (±10%) 50mA
• Accuracy ± 0.05 % (± 1 count)
• Display 4 Digit 0.5”seven Segment Red Led
• Working temperature 0 - 50 ºC
• Power Supply 90 to 270V AC / DC 50Hz
• Dimension 72 x 72 x 65 mm
• Weight 200 grams (Approx.)

The most time-consuming part of carrying out a microbial count is the actual counting process on petri dishes. Colony counters facilitate this task and as a result are essential in every bacteriological laboratory. Their particular advantages are the easy, rapid and reliable counting of bacterial colonies with very simple handling. SANSEL colony counter Model CC 100 is easy to use and allows fatigue-free and safe work thanks to its problem-free counting mechanism: Marking the colonies on the petri dish with the marker pen activates the counter.

Fearures :

• Long Life Electronic Pen
• 110 mm Dia Magnifying Glass
• Audible Buzzer Indication for Each Count
• Uniform Glare free illumination
• Wolffhugel Glass Grid with Focusing Facility
• x 1.7 Surface Magnification
• 230V AC Operating Supply

Accessories :

• Basic Instrument
• Magnifier
• Magnifier stand set
• Electronic Marker Pen
• Instruction manual

SANSEL Model TCAL 1402 / -20 Miniature calibrator bath are one of the smallest dry well calibrator in the world, which are ideally suited were necessary for fast calibration in process industries to calibrate Thermocouple, RTD, Indicator with sensor & transmitter with sensor. Temperature range of the TCAL 1402 / -20 covers from -15°C* to 75°C. These equipment are light weight, fast raising, quick settling, better stability & uniformity. TCAL 1402 / -20 Miniature calibrator bath’s temperature are adjusted simply using 4 keys on the controller, can be very quickly controlled the actual and set temperature can be displayed simultaneously on a 4+4 digit high brightness LCD. TCAL 1402 / -20 having interchangeable inserts to suit for calibration of different diameter of sensors (upto 16mm). Additional Inserts(optional) with special drillings are available to order.

Features :

• Wide temperature range -15* to 75°C
• Light weight - Less than 8 kg (Approx.)
• World class performance
• Fast calibration save time & money
• Simple, Convenient & easy operation
• High Bright LCD Display
• Rugged & most compact for onsite carry
• Inter changeable insert to suit different diameter sensor
• Supplied with rexein carry bag
• ISO / IEC 17025 Standard Accredited Calibration Certificate

Accessories

• Basic Instrument
• Standard well insert
• Well tool
• Spare fuses
• Instruction manual
• Mains card
• Carry bag
• Traceable calibration certificate

Optional

• Master Indicator with sensor
• Additional well insert
• Carrying case

Features :

•  Multi colour TFT display
•  Easy touch screen to configure & copy the datas
•  8 , 16 , 24 , 32 Channel Inputs with fixed & Universal Inputs
•  Analog Inputs like Thermocouple , RTD, mA, mV , V
•  Internal Memory for Datas upto 25, 000 records
•  USB 2.0 for PEN drive data transfer
•  Parallel port provided for direct printout the storage datas
•  PC Interface through RS 485 or RS 232 or USB or Ethernet (TCP/IP)
•  Common Alarm Output with H/L Settings for all channels
•  Easy Mounting , Compact Size and rugged
•  Supply 230V AC

“SANSEL” series TCAL 1501 / 250 is a micro controller based precision “Liquid temperature calibrator” generates true reference temperature. The temperature controller of the calibrators uses a auto tune FUZZY PID controller algorithm. This response closely follows the heating curve of an actual thermal system. Place the Thermometers, Thermocouples & RTDs to be calibrated in the calibrator. Set the temperature from the 4.3 inch true TFT display with touch screen. Both Block and set temperature can be read. When stabilization occurs, Simply read the temperature and re-calibrate the Thermometer, sensor etc, . or comparison with master RTDs reading.

Features :

• Wide range
• Easy to read colour TFT display
• Suitable to cover different size of sensor
• Fast and quick settling time
• High resolution and better stability
• Inbuilt magnetic stirrer for better uniformity
• No hazardous liquid
• Easy to carry for onsite application
• Inbuilt measuring facility
• NABL Calibration Certificate

Specifications :

• Display 4.3 inch true TFT display with touch screen
• Working Range Ambient to 250 °C / ( 32 to 300° F )
• Resolution 0.01 °C
• Stability ± 0.03 °C
• Accuracy better than ± 0.3 °C
• Uniformity ± 0.1 °C
• Measure inputs RTD-PT 50, PT 100, PT500, PT1000 / TC -J, K, R, S, T, E, B, N/mA/mV/ ohms
• Chamber dia x depth 80 x 140mm
• Testing dia depth 60 x 120 mm
• Temperature Medium Silicon Oil
• Multi Hole Well Provided for Different Types of Sensors
• Dimension in mm 340 x 175 x 425 (L* W * H) (Approx.)
• Power Supply 230V AC ± 10% / 50Hz (Optional 110V AC)

Accessories :

• Basic Instrument
• Cable for Thermostat Switch Test
• Cable for Thermocouple(TC) test probe
• Cable for RTD test probe
• Aluminum Dummy cover
• Teflon top cover
• Thermometer stand set
• Silicon oil – 1 liters
• SS insert bucket
• Stir magnet(2 nos)
• Instruction Manual
• Traceable Calibration Certificate
• Mains Card
• Spare Fuses

SANSEL Model TCAL 1402 / 500 Miniature calibrator bath are one of the smallest dry well calibrator in the world, which are ideally suited were necessary for fast calibration in process industries to calibrate Thermocouple, RTD, Indicator with sensor & transmitter with sensor. Temperature range of the TCAL 1402 / 500 covers from Ambient + 5°C to 500°C. These equipment are light weight, fast raising, quick settling, better stability & uniformity. TCAL 1402 / 500 Miniature calibrator bath’s temperature are adjusted simply using 4 keys on the controller, can be very quickly controlled the actual and set temperature can be displayed simultaneously on a 4+4 digit high brightness LCD. TCAL 1402 / 500 having interchangeable inserts to suit for calibration of different diameter of sensors (upto 20mm). Additional Inserts(optional) with special drillings are available to order.

Features :

• Wide temperature range Amb.+5 to 500°C
• Light weight - Less than 2 kg (Approx.)
• World class performance
• Fast calibration save time & money
• Simple, Convenient & easy operation
• High Bright LCD Display
• Rugged & most compact for onsite carry
• Inter changeable insert to suit different diameter sensor
• Supplied with rexein carry bag
• ISO / IEC 17025 Standard Accredited Calibration Certificate

Accessories

• Basic Instrument
• Standard well insert
• Well tool
• Spare fuses
• Instruction manual
• Mains card
• Carry bag
• Traceable calibration certificate

Optional

• Master Indicator with sensor
• Additional well insert
• Carrying case

SANSEL Model TCAL 1402 / 300 Miniature calibrator bath are one of the smallest dry well calibrator in the world, which are ideally suited were necessary for fast calibration in process industries to calibrate Thermocouple, RTD, Indicator with sensor & transmitter with sensor. Temperature range of the TCAL 1402 / 300 covers from Ambient + 5°C to 300°C. These equipment are light weight, fast raising, quick settling, better stability & uniformity. TCAL 1402 / 300 Miniature calibrator bath’s temperature are adjusted simply using 4 keys on the controller, can be very quickly controlled the actual and set temperature can be displayed simultaneously on a 4+4 digit high brightness LCD. TCAL 1402 / 300 having interchangeable inserts to suit for calibration of different diameter of sensors (upto 20mm). Additional Inserts(optional) with special drillings are available to order.

Features :

• Wide temperature range Amb. to 300°C
• Light weight - Less than 2 kg (Approx.)
• World class performance
• Fast calibration save time & money
• Simple, Convenient & easy operation
• High Bright LCD Display
• Rugged & most compact for onsite carry
• Inter changeable insert to suit different diameter sensor
• Supplied with rexein carry bag
• ISO / IEC 17025 Standard Accredited Calibration Certificate

Accessories

• Basic Instrument
• Standard well insert
• Well tool
• Spare fuses
• Instruction manual
• Mains card
• Carry bag
• Traceable calibration certificate

Optional

• Master Indicator with sensor
• Additional well insert
• Carrying case

These are Master Thermocouple without Cold Junction. This range is based on popular Standard Thermocouple range, Sensitivity & Length.
MTC are highly accurate and stable Thermocouple with minimum uncertainties. It offer wide temperature range which is ideal for all industrial applications. The size, length and Thermocouple Material are such that give the best and most stable results.

Features :

• Temperature range upto 1200 & 1500 deg C
• 6mm O.D & available different Dimensions
• Outer Sheath SS 316 / Inconel / High Alumina Tube
• High Accuracy & Stability
• Manufactured & Tested under strict quality control standards
• Cycled to Stability
• Fast Response
• Low Drift

SANSEL Model TCAL 1401 / -30 Dry well Temperature calibrator are high performance for industrial atmosphere and covering temperature range from -30* to 100°C. Which are ideally suited onsite calibration of thermocouple, RTDs, Indicator with sensors & 4-20mA signal transmitter with indicator in Food, Pharmaceutical and all types of process industries. Having it’s advantage of user friendly, light weight, portable, fast settling, better uniformity and accuracy over a wide temperature range. TCAL 1401 / -30 having interchangeable inserts to suit for calibration of different diameter of sensors (upto 16mm). Additional Inserts(optional) with special drillings are available to order.

Features :

• High Bright 4 + 4 digit 7 seg LCD Display with 4 keys
• Portable & Rugged
• Range from -30* to 100°C
• No Liquids, Safe dry Calibration
• Micro Controller Based Linearized High Accuracy
• Stable to ± 0.1°C
• Axial + Radial uniformity - better than ± 0.15°C
• Inter changeable insert to suit different diameter sensor - up to 22 mm
• ISO / IEC 17025 Standard Accredited Calibration Certificate

Accessories

• Basic Instrument
• Standard well insert
• Well tool
• Spare fuses
• Instruction manual
• Mains card
• Carry bag
• Traceable calibration certificate

Optional

• Master Indicator with sensor
• Additional well insert
• Carrying case

Features :

•  Large 2.8" TFT display with Touch screen
•  Ranges from -40 to 85 DegC / 0 to 100% RH / psychometric Converted Dew point
•  More resolution 0.01 DegC / 0.01 % RH
•  High Accuracy : ±0.2 DegC / ±0.8 % RH
•  Inbuilt rechargeable polymer Li-ion battery
•  Alarm facility
•  Comfortable and anti-slip grip
•  Portable & Rugged with carrying case
•  ISO/IEC 17025 Accredited Calibration certificate
• Optional High temperature sensors available on request for temperature ranges -50 to 100 DegC & -100 to 200 DegC

SSPRT is Highly Accurate Platinum Resistance Thermometer(PT 100) offer the temperature range of - 80 to 660ºC. SSPRT gives the benefit of high accuracy and low drift in a solid metal case. Wire wound resistance element give good stability with low temperature coefficient and high accuracy.
SSPRT is constructed with a 6 mm outer diameter of Inconel sheath of high durability. SSPRT is available in different accuracies and length. A special powder mixture is filled into the sensor capsule to support the element from mechanical shocks.

Features :

• Temperature range from -80 to 660 deg C
• 6mm O.D & available different Dimensions
• Outer Sheath SS 316 / Inconel / High Alumina Tube
• High Accuracy & Stability
• Manufactured & Tested under strict quality control standards
• Cycled to Stability
• Fast Response
• Low Drift

Specifications :

• Type PT 100 (four wire)
• Temperature Range -80 to 660
• Element PT 100
• Accuracy * Class A, 1/3, 1/5, 1/10 DIN
• Sheath Diameter 6mm
• Sheath Length 300mm, 450mm, 600mm
• Cable Length 1000mm or as Required
• Outer Sheath SS-316
• End Connection Flying Lead

Features :

• View the Count Display From Long Distance 4" , 8" Available in Different Segment Sizes (1" & 2" on Request)
• Different type of Mounting Wall, Selling, Panel, "L" Clamping
• 4 Digit Seven Segment LED Display • Seconds, Minutes, Hours Configurable
• Selectable Resolution 0.01 / 0.1 / 1
• 2 Relay Outputs with Selectable Delay Mode
• Front End Reset with Protection
• External Start / hold / Reset Options
• 10 Years Memory Backup )
• Supply Voltage 230V AC

We are a leading service provider for calibration of various types of parameters in all industries and our lab is accredited by (NABL)national accreditation board for testing and calibration laboratories from Chennai, Tamil Nadu, India.

Very Low Pressure ± 25 mbar
Type of Instruments CalibratedManometerLow pressure Transducer/TransmitterGaugesDifferential Pressure Indicator/TranmitterPressure Data LoggerPressure switchLow pressure Calibrators, etc.,

Absolute Pressure: 0.60 bar to 2 bar
Type of Instruments CalibratedBarometersAneroid barometerAbsolute gaugesAbsolute pressure sensor/TranmitterAbsolute pressure indicator/ controllerLogger and Calibrators etc

Vacuum: -0.1 bar to -0.99 bar
Type of Instruments CalibratedVacuum GaugeVacuum Tranduer/TransmitterVacuum Indicator/Controller/SwitchVacuum LoggerCalibrators etc.,

Pressure(Hydraulic and Pneumatic) 1 bar to 1000 bar and 0.1 bar to 35 bar
Type of Instruments CalibratedPressure CalibratorsPressure TransducerPressure TransmitterDigital Pressure GaugesPressure ControllerPnueumatic pressure gaugesHydraulic Pressure gaugesDifferential pressure indicators, etc.,

Mass/Weight 1 mg to 50 kg
Type of Instruments Calibrated(Accuracy class: E2, F1, F2, M1, M2, ETC., )Standard weight boxWeights, etc., Weighing Scale and Balance 1mg to 300 KgMicro balanceAnalytical balanceDigital balanceWeighing Scale

Volume 1µl to 5l
Type of Instruments CalibratedPipetteBuretteFlaskbeakerAll types of measuring cylinder

Acoustic Pressure : Range 94 & 114 DB
Type of instruments Calibratedsound level meter, etc., Contact RPM/Tachometer: 100 RPM to 10000 RPMNon - Contact RPM/Tachometer: 12 RPM to 99950 RPMType of Instruments CalibartedContact & Non contact type RPM IndicatorContact & Non contact type TachometerCentrifugal, etc., Dimensional(Basic Instrument, Gauge, etc., )Vernier CalipersExternal MicrometerPlunger Dail GaugeLever Type DailBore GaugeHeight GaugesDepth MicrometerDepth GaugesThickness GaugesSnap GaugeFeeler gaugeInternal Micrometerwidth GaugeDial Caliper GaugeMicrometer SettingPlain Plug GaugePistol CaliperThread Measuring WiresMeasuring Pin

We are a leading service provider for calibration of various types of parameters in all industries and our lab is accredited by (NABL)National Accreditation Board for Testing and Calibration laboratories from Chennai, Tamil Nadu, India.

Temperature(Contact) Range from -80 deg C to 1500 deg c

Type of Instruments Calibrated:Digital ThermometerGlass ThermometerDry block Calibrators
Thermocouple and RTD probesThermistorsTemperature RecorderTemperature Scanner/Data loggerTemperature Indicator with sensorTemperature GaugeTemperature TransmitterTemperature bath, etc., Mapping and Validation for single or multi pointFreezerincubatorovenfurnanceStorage roomsclean roomsdryercold roomsEnvironmental chambersHumidity Indicator/chamber, etc., Temperature(Non-Contact)Range from 0 deg c to 1500 deg c

Type of Instruments Calibrated
Non-Contact PyrometersIR thermometerBlack Body Source, ect., Humidity: Range from 5 to 60 deg c & 10 to 95%

Type of Instruments CalibratedHumidity sensors/TransmitterHumidity/Temperature loggerAnalog hygrometerdigital thermal hygrometerThermo hygro graphHumidity chamber etc., Note: Price May vary based on quantity and instruments