SAMS Engineering

Jafferkhanpet, Chennai, Tamil Nadu

It is essential to decide the wear rate at design stage, in doing so it is necessary to develop such an equipment which will serve the purpose of material testing. The purpose of friction and wear test

Product Code :SAMS DYN - 032

The Centrifugal Compressor Test Rig consists of a centrifugal blower driven by a variable speed electric motor. A motor controller is used to regulate the blower speed. Ducts are fitted to inlet & outlet of the blower. A damper in inlet duct is provided to regulate the intake air flow of the blower. A Pitot tube with differential manometer is used to measure the air flow rate. Two manometers are provided to measure intake & discharge pressure of air.

Product Code : SAMS AE - 002

In this test rig, performance of a Propeller can be investigated. The propeller is mounted on a shaft of DC motor. The load cell arrangement is used to measure the thrust force produced by the propeller.

Product Code : SAMS AE - 005

The setup consists of single cylinder, four stroke, VCR (Variable Compression Ratio) Diesel engine connected to eddy current type dynamometer for loading. The compression ratio can be changed without stopping the engine and without altering the combustion chamber

The setup consists of single cylinder, four stroke, VCR (Variable Compression Ratio) Petrol engine connected to eddy current type dynamometer for loading. The compression ratio can be changed without stopping the engine and without altering the combustion chamber

Performance Test

Heat Balance Test

Engine: 5 HP at 1500 RPM coupled with loading device on a common base plate.

To carry out the following experiments, Experiment to be performed: Morse Test.

Engine: 10HP at 1500RPM coupled with loading device on a common base plate.

Different Types of Loading:

Rope Brake Dynamometer Hydraulic Dynamometer Electrical Dynamometer

Product Code : SAMS THR - 006

Measuring tank & stop watch.

Basic piping-1

Orificemeter & venturimeter

Differential manometer

Product Code : SAMS HYD - 004

Francis turbine is a reaction turbine which was developed by an English born American engineer Sir J.B Francis. the water enter the turbine though the outer periphery of the runner in The redial direction & leaves the runner in axial direction & hence it is called a mixed flow turbine As the water flow to the the runner a part of pressure energy goes on changing in to kinetic energy. Thus the water though the runner is completely enclosed in a air tight casing & the casing & runner is always full of water.

Product Code : SAMS HYD - 006

Semi Circular Sectioned hollow ship model, provision for loading as Cargo and warship, fine arrangement for accurate angle measurement extra weight in Metric Unit for tilting coupled.

Product Code : SAMS HYD - 008

To study the Volumetric Efficiency of Compressor. Both Single stage compressor and Two stage compressor can be used. The setup consists of 6 channel digital temperature indicator with an energy meter and U Tube Manometer.

Product Code : SAMS HTL - 008

To study the Volumetric Efficiency of Compressor. Both Single stage compressor and Two stage compressor can be used. The setup consists of 6 channel digital temperature indicator with an energy meter and U Tube Manometer.

Product Code : SAMS HTL - 009

To determine the COP of given plant. The apparatus consists of a compressor, condenser, dryer, digital temperature indicator, sensor, pressure gauge & vacuum gauge. Eco-friendly R 134A is used as refrigerants in our Air Conditioning Test Rig. Our Air Conditioning Test Rig is highly useful in conducting experiments on a vapor compression air conditioning unit.

Product Code : SAMS R/AC - 001

To study the Volumetric Efficiency of Compressor. Both Single stage compressor and Two stage compressor can be used. The setup consists of 6 channel digital temperature indicator with an energy meter and U Tube Manometer.

Product Code : SAMS R/AC - 002

The Ice Plant Test rig works on simple compression refrigeration cycle and uses R134-a or R404-A as a refrigerant. These are environment friendly. It is also useful to understand working of vapour compression system, its performance and controls used. The arrangement of parts such that, all the parts are visible and working can be easily understood

Product Code : SAMS R/AC - 005

The Vortex Tube Test Rig is one of the non- conventional methods of cooling which has no moving parts. It requires only source of compressed air. Through this tube, when air is admitted at high pressure, from one end, hot sir is discharged and from the other end, cold air comes out. The test rig is designed such that all the performance can be evaluated.

Product Code : SAMS R/AC - 00

To Study The Shock Absorber

To plot the transmissibility curve of shock absorber

Product Code : SAMS AUTO - 002

It Consists of Column Frame, Pneumatic Cylinder, FRL, Double Acting Solenoid Valve, Load Measuring Sensor, Displacement Measuring Sensor, etc, . It used to test the all type of Compression Coil Spring in Two & Three Wheeler.

Product Code : SAMS AUTO - 003

These products are specially designed by our engineers to improve two and three wheeler design knowledge and troubleshooting technique to the students

Product Code : SAMS AUTO - 004