The apparatus is designed to help in conducting various experiments to illustrate and verify the principles and relations involved in the study of vibrations. Following experiments can be performed with this unit.

Product Code :SAMS DYN - 007

EEE Journal Bearing apparatus for investigating the distribution of pressure in slide bearings illustrates the principle of hydrodynamic lubrication. The distribution of pressure and the carrying capacity can be determined on a sliding bearing model at different bearing loads and speeds. The sliding bearing consists of a bearing journal driven by an electrical motor and the freely moving bearing housing. The bearing is loaded with different, interchangeable weights. The setup contains manometer tubes, dc motor, dc drive to control speed, set of weights, oil tank, Journal bearing along with the shaft.

Product Code :SAMS DYN - 011

The Pin And Disc wear Apparatus consists of a steel disc whose top surface is case hardened and ground. The disc is rotated by a single ph. Induction motor at 3 different speeds. The test pin is inserted in a pin guide so that one end of pin touches the rotating disc. The pin guide is mounted on a cantilever to which spring balance is attached.

Product Code :SAMS DYN - 021

This apparatus is useful for measurement of power transmitted for various input power conditions with varied belt tension. Belt slip or creep also can be measured. The apparatus consists of a variable speed D.C. Motor, driving pulley and driven pulley of equal diameters. The pulleys are mounted on input shaft (motor shaft) and output shaft. The driven pulley can slide on the base only with bearing block to change the initial tension in belt

Product Code :SAMS DYN - 024

Average surface heat transfer coefficient for a pipe losing heat by forced convection to air flowing through it can be obtained for different air flow and heat flow rates. The unit consists of a circular pipe, loosing heat by forced convection to air, being forced through it. Constant heat flux is added to pipe by an electrical heater, provided with input control. The pipe surface temperature is measured at various points along length of pipe using thermocouples. Temperature of air at inlet and outlet of test section is measured using temperature indicator.

Product Code : SAMS AE - 004

Working Section : Made of two laminated glass / acrylic sheets which are closely spaced and fixed in a leak proof moulding

Flow table : Width = minimum 300mm, Length = minimum 500mm,

Dye Tank With Flow Control : Stainless steel tank with minimum 1L capacity Dye injection facility

Sump Tank : Stainless steel tank with minimum 40L capacity

Water circulation : Suitable capacity pumpProduct Code : SAMS DYN - 002

Conforming to the specifications and tolerance in accordance to I.S.-1199 and latest I.S.-7320. Consists of slump cone frustums in shape 10cm. diam at top, 20cms. At bottom and 30cms, high fitted with foot piece and handle, one portable base plate having cleats to accommodate cone and tamping rod 16mm diam x 60cms. Long bullet at one end graduated 0-30cms in one millimeter division

Product Code : SAMS CVL - 006

Conforming to the specifications and tolerance in accordance to I.S.-2720, Part-XVI used for the determination of the laboratory C.B.R. consists of : - 01.) Load Frame Hand operated capacity 50 KN (5000 kgs.) with high and low rate of travel of the lead screw. 02.).C.B.R. Mould:-Conforming to the specifications and tolerance in accordance to I.S.-9669-1980 made of chromium steel 150mm.

Product Code : SAMS CVL - 011

Conforming to the specifications and tolerance in accordance to I.S. 4031, 5516, 1727 &4828. The equipment is used for the determination of the fineness of the cement in terms of specific surface expressed as total surface area in square centimeters per gram of cement. This is variable flow type air parameters. The equipment consists of one each permeability cell 12.5mm.

Product Code : SAMS CVL - 012

The test is applicable to hot mix designs using bitumen and aggregates upto a maximum size of 25mm. In this method, the resistance to plastic deformation of cylindrical specimen of bitumenous mixture is measured when the same is loaded at periphery at 5 cm per min. This test procedure is used in designing and evaluating bitumenous paving mixes.

Product Code : SAMS CVL - 015

Apparatus consist of four spring steel columns which are put along a vertical wooden board. These four columns have different end conditions as below: 1. Both ends pinned 2. Both ends fixed 3. One end pinned and other fixed 4. One end fixed and other end free Apparatus will be supplied complete with a supporting stand and a set of weights.

Product Code : SAMS AM - 002

Apparatus consists of a steel bar which is used to make the different curved member Viz. circle, semicircle with straight arm, a quadrant of a circle and quadrant of a circle with straight arm. The bottom ends of the members are fixed to the base. Under the application of load at free end, its horizontal and vertical deflection can be measured with the help of dial gauges.

Product Code : SAMS AM - 003

Apparatus consists of a three parallel bar suspension system with elastic beam at their upper and lower ends. The upper ends of the two outer suspension rods are tied to a vertical wooden board while central suspension rod may be tied to the center of another elastic beam supported at two outer ends only. Apparatus to be supplied should be complete with a supporting stand and a set of weights.

Product Code : SAMS AM - 004

Apparatus consists of a mild steel beam 2.5cm X 3mm in cross section and 100cm long, pinned to two supports 70cm apart situated symmetrically. One of the ends can be fixed or given a known slope by applying a known moment at the end with the help of suspended loads. At the other end also a known moment can be applied. Vertical loads can be applied at various points along the span of the beam. A Dial gauge with 25mm travel ( with a magnetic base) may be supplied with the apparatus.

Product Code : SAMS AM - 005

Apparatus consists of two mild steel cables 0.5cm diameter in cross section and 150cm long, pinned to two supports 90cm apart situated symmetrically. One of the ends can be converted to a roller by applying a known load at the end with the help of suspended pulley system. Vertical loads can be applied at various points along the span of the beam. A dial gauge with 25mm travel (with a magnetic base) will be supplied with the apparatus.

Product Code : SAMS AM - 006

Apparatus made up of M.S. plate of rectangular section of 3mm thick X 40cm wide. Frame is provided with a provision to achieve different end conditions viz. hinged, roller & fixed. The size of portal will be 40cm X 60 cm. Portal may also have a provision for pulley arrangement and hook arrangement for horizontal loading at different positions. A dial gauge with 25mm travel (with a magnetic base) is supplied with the apparatus. Apparatus will be supplied complete with a supporting stand and a set of weights.

Product Code : SAMS AM - 007

Apparatus consists of three suspension members (spring balances) of different stiffness which are jointed at a point to form the redundant joint. The upper end of the suspension members being tied in a position to a vertical wooden board. Arrangement is provided to apply a vertical load at the joint and to measure its horizontal and vertical displacement on a paper and also elongations and forces in the suspension members by the help of dial gauges. Two dial gauges with 25mm travel (with magnetic bases) are supplied with the apparatus.

Product Code : SAMS AM - 008

Apparatus consists of a mild steel angle of size 1" X 1" X 1/8" or an equivalent metric units of length 80 cm is tied as a cantilever beam. The beam should be fixed at one end such that the rotation of 45degree intervals are given and clamped such that the principal axis of its cross-section may be inclined at any angle with the horizontal and vertical planes. Also arrangement will be provided to apply vertical load at the free end of the cantilever and to measure horizontal and vertical deflection of the free end.

Product Code : SAMS AM - 009

Low cost effective teaching

Self contained

Bench mounted

Product Code : SAMS AM - 010

This item is similar to the wall type but is intended for use in laboratories where wall space is limited. At thick plywood piece of thickness 12 mm having substantial metal stand with 2 set of z-pulley and 3 set of ( 50 x 5 gm) slotted weights.

Product Code : SAMS AM - 011

Sudden expansion-1/2to 1

Sudden expansion-1/2to 1

Differential manometer.

Measuring tank 400 x 300 x 300mm

Product Code : SAMS HYD - 002

Types of notch : 600 v notch , rectangular notch, Trapezoidal.

Flow channel : 250 x 250x 1250 mm with notches fitting arrangement

Pipes and Valves : 1 G.I. piping and 1 Brass valves.

Water storage Unit : Sump Tank 900 x 400 x 400 mm M.S. tank with F.R.P. coating. Or S.S. tank.

Product Code : SAMS HYD - 003

A pitot tube made up of small copper tube is held in a pipe line. A screw type arrangement is provided to raise or lower this pitot tube. The open end is connected to a manometer.

Product Code : SAMS HYD - 010

A hydraulic flume of c/s 200x300 mm & 6000 mm length with transparent window on either sides of 1000 mm length.

Sliding gates one at upstream and other at the downstream side.

Screw jack for change of the slope of the flume.

A Sump tank of sufficient capacity.

Product Code : SAMS HYD - 011

To determine the thermal conductivity of liquids by guarded hot plate. The apparatus consists of a main heater and a radial guard heater sandwiched between copper plates. The specimen in the form of slabs of equal thickness are placed on either sides of heaters and cooling plates through which water is circulated are on the other sides of the specimen. The radial guard heater ensures all heat of the main heater to pass axially through the specimens which is collected by cooling plates

Product Code : SAMS HTL - 001

The apparatus is designed to determine total thermal resistance and thermal conductivity of lagged pipe. Lagging of pipes is required to prevent leakages of heat. In Lagged pipe Apparatus, three concentric pipes are arranged between two supports. The gap between the pipes are filled compactly by two different insulating materials and heater is provided at the centre of inner pipe. Temperature at various points is measured with Temperature Indicator.

Product Code : SAMS HTL - 002

It is designed to study the temperature distribution along the length of a vertical pipe in natural convection. The unit consists of a vertical brass pipe heated by a cartridge heater inside it. It is fitted in an enclosure to provide undisturbed natural convection currents. Thermocouples are attached on the pipe to measure local temperatures. Heater input is measured on voltmeter and ammeter.

Product Code : SAMS HTL - 003

Average surface heat transfer coefficient for a pipe losing heat by forced convection to air flowing through it can be obtained for different air flow and heat flow rates. The unit consists of a circular pipe, loosing heat by forced convection to air, being forced through it. Constant heat flux is added to pipe by an electrical heater, provided with input control. The pipe surface temperature is measured at various points along length of pipe using thermocouples. Temperature of air at inlet and outlet of test section is measured using temperature indicator.

Product Code : SAMS HTL - 004

The apparatus is designed to calculate the heat transfer rate from the fin and the fin effectiveness in natural & forced convection. The apparatus consist of a pin type fin heated by a band heater at one end. It consists of a channel in which the pin fin is tested in both natural as well as forced convection. A centrifugal blower draws air over the fin. The blower is operated to touch the pin fin in forced convection only Thermocouples are attached along the length of fin to note down the longitudinal temperature gradient.

Product Code : SAMS HTL - 005

The apparatus is used to determine the Radiation Stefan Boltzmann constant. The apparatus consists of a hemisphere surrounded by hot water. Hot water is obtained from a hot water tank with instant heater. When the blackened disc is inserted at the center of hemisphere, heat is transferred into the disc from hemisphere by radiation and its temperature begins to rise, and from temperature raise rate, Stefan Boltzmann constant is determined.

Product Code : SAMS HTL - 006

To study the Volumetric Efficiency of Compressor. Both Single stage compressor and Two stage compressor can be used. The setup consists of 6 channel digital temperature indicator with an energy meter and U Tube Manometer.

Product Code : SAMS HTL - 010

To study the Volumetric Efficiency of Compressor. Both Single stage compressor and Two stage compressor can be used. The setup consists of 6 channel digital temperature indicator with an energy meter and U Tube Manometer.

Product Code : SAMS HTL - 011

This method is intended for the determination of the open flash point and fire point of petroleum products except when the clean and open cup is specified. The Apparatus consists of brass test cup with handle removable cover, with spring operated rotating shutter for smooth operation, having a pilot jet, stirrer with flexible shaft.

Product Code : SAMS FTL - 004

This apparatus is used for determination of flash and fire pt. of petroleum products except fuel oils and those having an open cup flash below 790C. The apparatus consists of a cup, heating plate specific dimensions, thermometer clip and test flame attachment with service 1 joints for passing over test liquids surface in the prescribed manner. Heating is controlled by means of energy regulator fitted to apparatus Suitable for operation on 220 V. AC.

Product Code : SAMS FTL - 005

This is used for determining drop point of greases as per IP 31, 132 & ASTM-D-566. It is an indication of the critical temperature of the solid or semi solid to the liquid state. The apparatus consists of brass sleeve and case with metal cup and a glass boiling tube with cork fitted to a bath (Beaker) is provided. A FHP Motorized stirrer and electrical heater with energy regulator control is also provided.

Product Code : SAMS FTL - 007

The complete instrument comprises of stove hammer finished shield, stainless steel bath with electrical heating arrangements, suitable to operate on , 220 volts A.C Mains or gas heating arrangements, with tap, silver plated oil cup with precision stain less steel jet, cup cover, ball valve, thermometer clip, stirrer and M.S sheet stand With leveling screws.

Product Code : SAMS FTL - 010

This apparatus is used for determination of flash and fire pt of petroleum products except fuel oils and those having an open cup flash below 790C. The apparatus consists of a cup, heating plate specific dimensions, thermometer clip and test flame attachment with service 1 joints for passing over test liquids surface in the prescribed manner.

Product Code : SAMS FTL - 014

The apparatus has been designed to introduce students to the fundamental characteristics of the behavior of the particle system, in particular the relationship between the drag coefficient of falling particles and Reynolds number

Product Code : SAMS MTL - 004

This apparatus is useful for determining the harden ability of steels by end quench test. The test consists of heating a standard size specimen to a given temperature for a specific period of time, followed by a water quenching of one end under specified conditions and measuring the hardness at various points from quenched end along the length of test piece.

Product Code : SAMS MET - 003

Non-destructive testing (NDT) is a wide group of analysis techniques used in science and industry to evaluate the properties of a material, component or system without causing damage

Product Code : SAMS NDT - 002

Conforming to the specifications and tolerance in accordance to I.S.2720 part-v and latest I.S.9259.Consists of a hard rubber base carrying a sliding carriage assembly to which a brass cup is hinged. The cup is raised and allowed to fall through a height of 1cm by the help of a lead screw provided at the back of the sliding carriage.

Conforming to the specifications and tolerance in accordance to I.S.-2720 consists of followings:-Glass plate 20cm x 15cm. with ground edge, Stainless steel spatula 2cm. wide and 8cms. Long with wooden handle, Brass rod 3mm. dia, Measuring cylinder 25 ml x 0.5 ml graduations.

Conforming to the specifications and tolerance in accordance to I.S.-2720 Pt.-XV. The equipment consists of followings: - Loading Unit:-maximum capacity 20kg/cm.sq. Consisting of loading yoke connected to a lever arm with a counterbalancing adjustment and having a lever ration 1: 10. The whole assembly being mounted on a steel frame. Consolidation cell assembly.

Conforming to the Specifications and tolerance in accordance to I.S.-2720 Part-XXVIII consists of :- Small sand pouring cylinder 3 liter capacity mounted above a pouring cone and separated as a shutter hole. Cylindrical Calibrating container internal diam 100mm and internal depth 150mm fitted with a flendge 5 cm. wide. Metal Tray 30cms square and 4 cms. Deep with a 10cms. Hole in the centre.

Conforming to the Specifications and tolerance in accordance to I.S.-2720 Part-XXVIII consists of :- Small sand pouring cylinder 3 liter capacity mounted above a pouring cone and separated as a shutter hole. Cylindrical Calibrating container internal diam 100mm and internal depth 150mm fitted with a flendge 5 cm. wide. Metal Tray 30cms square and 4 cms. Deep with a 10cms. Hole in the centre.

Conforming to the Specifications and tolerance in accordance to I.S.-2720 Part-XXVIII consists of :- Small sand pouring cylinder 3 liter capacity mounted above a pouring cone and separated as a shutter hole. Cylindrical Calibrating container internal diam 100mm and internal depth 150mm fitted with a flendge 5 cm. wide. Metal Tray 30cms square and 4 cms. Deep with a 10cms. Hole in the centre

The apparatus is designed to help in conducting various experiments to illustrate and verify the principles and relations involved in the study of vibrations. Following experiments can be performed with this unit.

Product Code :SAMS DYN - 007

EEE Journal Bearing apparatus for investigating the distribution of pressure in slide bearings illustrates the principle of hydrodynamic lubrication. The distribution of pressure and the carrying capacity can be determined on a sliding bearing model at different bearing loads and speeds. The sliding bearing consists of a bearing journal driven by an electrical motor and the freely moving bearing housing. The bearing is loaded with different, interchangeable weights. The setup contains manometer tubes, dc motor, dc drive to control speed, set of weights, oil tank, Journal bearing along with the shaft.

Product Code :SAMS DYN - 011

The Pin And Disc wear Apparatus consists of a steel disc whose top surface is case hardened and ground. The disc is rotated by a single ph. Induction motor at 3 different speeds. The test pin is inserted in a pin guide so that one end of pin touches the rotating disc. The pin guide is mounted on a cantilever to which spring balance is attached.

Product Code :SAMS DYN - 021

This apparatus is useful for measurement of power transmitted for various input power conditions with varied belt tension. Belt slip or creep also can be measured. The apparatus consists of a variable speed D.C. Motor, driving pulley and driven pulley of equal diameters. The pulleys are mounted on input shaft (motor shaft) and output shaft. The driven pulley can slide on the base only with bearing block to change the initial tension in belt

Product Code :SAMS DYN - 024

Average surface heat transfer coefficient for a pipe losing heat by forced convection to air flowing through it can be obtained for different air flow and heat flow rates. The unit consists of a circular pipe, loosing heat by forced convection to air, being forced through it. Constant heat flux is added to pipe by an electrical heater, provided with input control. The pipe surface temperature is measured at various points along length of pipe using thermocouples. Temperature of air at inlet and outlet of test section is measured using temperature indicator.

Product Code : SAMS AE - 004

Working Section : Made of two laminated glass / acrylic sheets which are closely spaced and fixed in a leak proof moulding

Flow table : Width = minimum 300mm, Length = minimum 500mm,

Dye Tank With Flow Control : Stainless steel tank with minimum 1L capacity Dye injection facility

Sump Tank : Stainless steel tank with minimum 40L capacity

Water circulation : Suitable capacity pumpProduct Code : SAMS DYN - 002

Conforming to the specifications and tolerance in accordance to I.S.-1199 and latest I.S.-7320. Consists of slump cone frustums in shape 10cm. diam at top, 20cms. At bottom and 30cms, high fitted with foot piece and handle, one portable base plate having cleats to accommodate cone and tamping rod 16mm diam x 60cms. Long bullet at one end graduated 0-30cms in one millimeter division

Product Code : SAMS CVL - 006

Conforming to the specifications and tolerance in accordance to I.S.-2720, Part-XVI used for the determination of the laboratory C.B.R. consists of : - 01.) Load Frame Hand operated capacity 50 KN (5000 kgs.) with high and low rate of travel of the lead screw. 02.).C.B.R. Mould:-Conforming to the specifications and tolerance in accordance to I.S.-9669-1980 made of chromium steel 150mm.

Product Code : SAMS CVL - 011

Conforming to the specifications and tolerance in accordance to I.S. 4031, 5516, 1727 &4828. The equipment is used for the determination of the fineness of the cement in terms of specific surface expressed as total surface area in square centimeters per gram of cement. This is variable flow type air parameters. The equipment consists of one each permeability cell 12.5mm.

Product Code : SAMS CVL - 012

The test is applicable to hot mix designs using bitumen and aggregates upto a maximum size of 25mm. In this method, the resistance to plastic deformation of cylindrical specimen of bitumenous mixture is measured when the same is loaded at periphery at 5 cm per min. This test procedure is used in designing and evaluating bitumenous paving mixes.

Product Code : SAMS CVL - 015

Apparatus consist of four spring steel columns which are put along a vertical wooden board. These four columns have different end conditions as below: 1. Both ends pinned 2. Both ends fixed 3. One end pinned and other fixed 4. One end fixed and other end free Apparatus will be supplied complete with a supporting stand and a set of weights.

Product Code : SAMS AM - 002

Apparatus consists of a steel bar which is used to make the different curved member Viz. circle, semicircle with straight arm, a quadrant of a circle and quadrant of a circle with straight arm. The bottom ends of the members are fixed to the base. Under the application of load at free end, its horizontal and vertical deflection can be measured with the help of dial gauges.

Product Code : SAMS AM - 003

Apparatus consists of a three parallel bar suspension system with elastic beam at their upper and lower ends. The upper ends of the two outer suspension rods are tied to a vertical wooden board while central suspension rod may be tied to the center of another elastic beam supported at two outer ends only. Apparatus to be supplied should be complete with a supporting stand and a set of weights.

Product Code : SAMS AM - 004

Apparatus consists of a mild steel beam 2.5cm X 3mm in cross section and 100cm long, pinned to two supports 70cm apart situated symmetrically. One of the ends can be fixed or given a known slope by applying a known moment at the end with the help of suspended loads. At the other end also a known moment can be applied. Vertical loads can be applied at various points along the span of the beam. A Dial gauge with 25mm travel ( with a magnetic base) may be supplied with the apparatus.

Product Code : SAMS AM - 005

Apparatus consists of two mild steel cables 0.5cm diameter in cross section and 150cm long, pinned to two supports 90cm apart situated symmetrically. One of the ends can be converted to a roller by applying a known load at the end with the help of suspended pulley system. Vertical loads can be applied at various points along the span of the beam. A dial gauge with 25mm travel (with a magnetic base) will be supplied with the apparatus.

Product Code : SAMS AM - 006

Apparatus made up of M.S. plate of rectangular section of 3mm thick X 40cm wide. Frame is provided with a provision to achieve different end conditions viz. hinged, roller & fixed. The size of portal will be 40cm X 60 cm. Portal may also have a provision for pulley arrangement and hook arrangement for horizontal loading at different positions. A dial gauge with 25mm travel (with a magnetic base) is supplied with the apparatus. Apparatus will be supplied complete with a supporting stand and a set of weights.

Product Code : SAMS AM - 007

Apparatus consists of three suspension members (spring balances) of different stiffness which are jointed at a point to form the redundant joint. The upper end of the suspension members being tied in a position to a vertical wooden board. Arrangement is provided to apply a vertical load at the joint and to measure its horizontal and vertical displacement on a paper and also elongations and forces in the suspension members by the help of dial gauges. Two dial gauges with 25mm travel (with magnetic bases) are supplied with the apparatus.

Product Code : SAMS AM - 008

Apparatus consists of a mild steel angle of size 1" X 1" X 1/8" or an equivalent metric units of length 80 cm is tied as a cantilever beam. The beam should be fixed at one end such that the rotation of 45degree intervals are given and clamped such that the principal axis of its cross-section may be inclined at any angle with the horizontal and vertical planes. Also arrangement will be provided to apply vertical load at the free end of the cantilever and to measure horizontal and vertical deflection of the free end.

Product Code : SAMS AM - 009

Low cost effective teaching

Self contained

Bench mounted

Product Code : SAMS AM - 010

This item is similar to the wall type but is intended for use in laboratories where wall space is limited. At thick plywood piece of thickness 12 mm having substantial metal stand with 2 set of z-pulley and 3 set of ( 50 x 5 gm) slotted weights.

Product Code : SAMS AM - 011

Sudden expansion-1/2to 1

Sudden expansion-1/2to 1

Differential manometer.

Measuring tank 400 x 300 x 300mm

Product Code : SAMS HYD - 002

Types of notch : 600 v notch , rectangular notch, Trapezoidal.

Flow channel : 250 x 250x 1250 mm with notches fitting arrangement

Pipes and Valves : 1 G.I. piping and 1 Brass valves.

Water storage Unit : Sump Tank 900 x 400 x 400 mm M.S. tank with F.R.P. coating. Or S.S. tank.

Product Code : SAMS HYD - 003

A pitot tube made up of small copper tube is held in a pipe line. A screw type arrangement is provided to raise or lower this pitot tube. The open end is connected to a manometer.

Product Code : SAMS HYD - 010

A hydraulic flume of c/s 200x300 mm & 6000 mm length with transparent window on either sides of 1000 mm length.

Sliding gates one at upstream and other at the downstream side.

Screw jack for change of the slope of the flume.

A Sump tank of sufficient capacity.

Product Code : SAMS HYD - 011

To determine the thermal conductivity of liquids by guarded hot plate. The apparatus consists of a main heater and a radial guard heater sandwiched between copper plates. The specimen in the form of slabs of equal thickness are placed on either sides of heaters and cooling plates through which water is circulated are on the other sides of the specimen. The radial guard heater ensures all heat of the main heater to pass axially through the specimens which is collected by cooling plates

Product Code : SAMS HTL - 001

The apparatus is designed to determine total thermal resistance and thermal conductivity of lagged pipe. Lagging of pipes is required to prevent leakages of heat. In Lagged pipe Apparatus, three concentric pipes are arranged between two supports. The gap between the pipes are filled compactly by two different insulating materials and heater is provided at the centre of inner pipe. Temperature at various points is measured with Temperature Indicator.

Product Code : SAMS HTL - 002

It is designed to study the temperature distribution along the length of a vertical pipe in natural convection. The unit consists of a vertical brass pipe heated by a cartridge heater inside it. It is fitted in an enclosure to provide undisturbed natural convection currents. Thermocouples are attached on the pipe to measure local temperatures. Heater input is measured on voltmeter and ammeter.

Product Code : SAMS HTL - 003

Average surface heat transfer coefficient for a pipe losing heat by forced convection to air flowing through it can be obtained for different air flow and heat flow rates. The unit consists of a circular pipe, loosing heat by forced convection to air, being forced through it. Constant heat flux is added to pipe by an electrical heater, provided with input control. The pipe surface temperature is measured at various points along length of pipe using thermocouples. Temperature of air at inlet and outlet of test section is measured using temperature indicator.

Product Code : SAMS HTL - 004

The apparatus is designed to calculate the heat transfer rate from the fin and the fin effectiveness in natural & forced convection. The apparatus consist of a pin type fin heated by a band heater at one end. It consists of a channel in which the pin fin is tested in both natural as well as forced convection. A centrifugal blower draws air over the fin. The blower is operated to touch the pin fin in forced convection only Thermocouples are attached along the length of fin to note down the longitudinal temperature gradient.

Product Code : SAMS HTL - 005

The apparatus is used to determine the Radiation Stefan Boltzmann constant. The apparatus consists of a hemisphere surrounded by hot water. Hot water is obtained from a hot water tank with instant heater. When the blackened disc is inserted at the center of hemisphere, heat is transferred into the disc from hemisphere by radiation and its temperature begins to rise, and from temperature raise rate, Stefan Boltzmann constant is determined.

Product Code : SAMS HTL - 006

To study the Volumetric Efficiency of Compressor. Both Single stage compressor and Two stage compressor can be used. The setup consists of 6 channel digital temperature indicator with an energy meter and U Tube Manometer.

Product Code : SAMS HTL - 010

To study the Volumetric Efficiency of Compressor. Both Single stage compressor and Two stage compressor can be used. The setup consists of 6 channel digital temperature indicator with an energy meter and U Tube Manometer.

Product Code : SAMS HTL - 011

This method is intended for the determination of the open flash point and fire point of petroleum products except when the clean and open cup is specified. The Apparatus consists of brass test cup with handle removable cover, with spring operated rotating shutter for smooth operation, having a pilot jet, stirrer with flexible shaft.

Product Code : SAMS FTL - 004

This apparatus is used for determination of flash and fire pt. of petroleum products except fuel oils and those having an open cup flash below 790C. The apparatus consists of a cup, heating plate specific dimensions, thermometer clip and test flame attachment with service 1 joints for passing over test liquids surface in the prescribed manner. Heating is controlled by means of energy regulator fitted to apparatus Suitable for operation on 220 V. AC.

Product Code : SAMS FTL - 005

This is used for determining drop point of greases as per IP 31, 132 & ASTM-D-566. It is an indication of the critical temperature of the solid or semi solid to the liquid state. The apparatus consists of brass sleeve and case with metal cup and a glass boiling tube with cork fitted to a bath (Beaker) is provided. A FHP Motorized stirrer and electrical heater with energy regulator control is also provided.

Product Code : SAMS FTL - 007

The complete instrument comprises of stove hammer finished shield, stainless steel bath with electrical heating arrangements, suitable to operate on , 220 volts A.C Mains or gas heating arrangements, with tap, silver plated oil cup with precision stain less steel jet, cup cover, ball valve, thermometer clip, stirrer and M.S sheet stand With leveling screws.

Product Code : SAMS FTL - 010

This apparatus is used for determination of flash and fire pt of petroleum products except fuel oils and those having an open cup flash below 790C. The apparatus consists of a cup, heating plate specific dimensions, thermometer clip and test flame attachment with service 1 joints for passing over test liquids surface in the prescribed manner.

Product Code : SAMS FTL - 014

The apparatus has been designed to introduce students to the fundamental characteristics of the behavior of the particle system, in particular the relationship between the drag coefficient of falling particles and Reynolds number

Product Code : SAMS MTL - 004

This apparatus is useful for determining the harden ability of steels by end quench test. The test consists of heating a standard size specimen to a given temperature for a specific period of time, followed by a water quenching of one end under specified conditions and measuring the hardness at various points from quenched end along the length of test piece.

Product Code : SAMS MET - 003

Non-destructive testing (NDT) is a wide group of analysis techniques used in science and industry to evaluate the properties of a material, component or system without causing damage

Product Code : SAMS NDT - 002

Conforming to the specifications and tolerance in accordance to I.S.2720 part-v and latest I.S.9259.Consists of a hard rubber base carrying a sliding carriage assembly to which a brass cup is hinged. The cup is raised and allowed to fall through a height of 1cm by the help of a lead screw provided at the back of the sliding carriage.

Conforming to the specifications and tolerance in accordance to I.S.-2720 consists of followings:-Glass plate 20cm x 15cm. with ground edge, Stainless steel spatula 2cm. wide and 8cms. Long with wooden handle, Brass rod 3mm. dia, Measuring cylinder 25 ml x 0.5 ml graduations.

Conforming to the specifications and tolerance in accordance to I.S.-2720 Pt.-XV. The equipment consists of followings: - Loading Unit:-maximum capacity 20kg/cm.sq. Consisting of loading yoke connected to a lever arm with a counterbalancing adjustment and having a lever ration 1: 10. The whole assembly being mounted on a steel frame. Consolidation cell assembly.

Conforming to the Specifications and tolerance in accordance to I.S.-2720 Part-XXVIII consists of :- Small sand pouring cylinder 3 liter capacity mounted above a pouring cone and separated as a shutter hole. Cylindrical Calibrating container internal diam 100mm and internal depth 150mm fitted with a flendge 5 cm. wide. Metal Tray 30cms square and 4 cms. Deep with a 10cms. Hole in the centre.

Conforming to the Specifications and tolerance in accordance to I.S.-2720 Part-XXVIII consists of :- Small sand pouring cylinder 3 liter capacity mounted above a pouring cone and separated as a shutter hole. Cylindrical Calibrating container internal diam 100mm and internal depth 150mm fitted with a flendge 5 cm. wide. Metal Tray 30cms square and 4 cms. Deep with a 10cms. Hole in the centre.

Conforming to the Specifications and tolerance in accordance to I.S.-2720 Part-XXVIII consists of :- Small sand pouring cylinder 3 liter capacity mounted above a pouring cone and separated as a shutter hole. Cylindrical Calibrating container internal diam 100mm and internal depth 150mm fitted with a flendge 5 cm. wide. Metal Tray 30cms square and 4 cms. Deep with a 10cms. Hole in the centre