Multifunctional electronic motor protection: Overload, Earth Fault, Thermistor, Single phasing, Phase unbalance, Stall protection etc.Flexible software for motor control: Built-in software logic like DOL, Star-Delta, Reversing Starter, eliminates complete control wiring.Detailed operating, service and diagnostics data: Provides details of motor load, fault messages, motor stopstart times, overload trips etc.Parameterization done via RS- 485 port through PCPG & Direct Communication via PROFIBUS DP. Benefits to customerReduced plant breakdowns & increased productivityPredictive Maintenance & Increased UPTIMECost SavingsEasy diagnosticsFaster commissioning plant start-up

Solar DCDB - is used to protect the system if there is any fault during failure on DC side. A very crucial part of SPV system as there should be adequate protection on DC side. The DCDB incorporates isolatorBreaker to switch off the system during fault, there is a meter which tells you exact PV array voltage and current you are getting. It also have surge protection to save your system from any surges occurred due to fault or other phenomenon. These panel are customized as per the design of the solar plant.It is Used where the DC current rating is very high and incoming and outgoing of the DC current is need to be fused. High Quality DC BusmanEq fuses are used for incoming and outgoing through Buss bar. Surge Protection is provided in this panel in order to absorb excess surges in the system. Outdoor Type panels are also available- Picture ENAM securities outdoor panel

PCCMCC panels are made up of 1416 SWG CRCA material semi bolted structure firmly supported. Ensures desired breaking capacities, temperature rise & IP protection. Enough Space for incoming & outgoing Cable termination. Outgoing terminals are stud type as standard practice. All starters are Type Two Co-ordinated. CT terminals, Cable Alley Illumination Lamp, Space Heaters with Thermostats are standard features of our Panel boards.

All boards are combination of 14 & 1618 SWG sheet steel, free standing, extensible, totally enclosed, dust tight, vermin-proof cubicle, flush dead front and of modular construction suitable for 3 phase 415V 4 wire 50 Hertz system TN-S neutrals grounding. All boards are accessible from the front or as shown on Drgs and specified in the equipment data sheet, considering ease of maintenance of switch fuses, bus bars, cable terminations, meters etc. Cables entries can be both from top as well as bottom. All panels are CNC machine pressed with punched openings for meters etc. mounted on a 75mm high base channel frame. All sheet steel are made rust free through a process of degreasing, derusting, phosphating, activation etc. The panels are finished with powder coating of approved color. Engraved plasticaluminum labels are provided indicating the feeder details, and capacity and danger signs. The boards accommodate air insulated bus bars, ACB, MCCBs, SF units with HRC fuses, starters, meters, relays, contactors etc. are arranged in suitable tiers. The switch board are fully compartmentalized in vertical tiers housing the feeder switches in totally enclosed independent compartments. Each compartment is self- sufficient with switch unit, fuses, contactors, relays, indicating lamps and optionally inter-locked door with facility for padlocking. Each switch or MCCB or ACB will have provision for locking in the OFF position for life safety. Each feeder will terminate in an independent labelled terminal block. All power terminals above 16 sq mm are stud or bus bar type. All terminations are shrouded in an approved manner.

Fully compartmentalized, Drawout Modules are with-drawable with 3, distinct position viz Test, Service 8 Isolation, Drawout Modules of same size are fully interchangeable, Totally enclosed, vermin-proof & dust proof Vertical Busbar system, Automatic safety shutter for the vertical bus-bar, Main bus-bars are easily approachable from the top, Self-aligning & self-disconnecting power &auxiliary Control contacts, Vertical bus-bars are provided with contact Element for Drawout contacts, Spring Loaded Earth Contacts, Swivelling lever- guide for easy withdrawal of the modules without any additional tools, Feeder & cable alley doors open in opposite, Feeder & cable alley doors open in opposite.

Multifunctional electronic motor protection: Overload, Earth Fault, Thermistor, Single phasing, Phase unbalance, Stall protection etc.Flexible software for motor control: Built-in software logic like DOL, Star-Delta, Reversing Starter, eliminates complete control wiring.Detailed operating, service and diagnostics data: Provides details of motor load, fault messages, motor stopstart times, overload trips etc.Parameterization done via RS- 485 port through PCPG & Direct Communication via PROFIBUS DP. Benefits to customerReduced plant breakdowns & increased productivityPredictive Maintenance & Increased UPTIMECost SavingsEasy diagnosticsFaster commissioning plant start-up

Solar DCDB - is used to protect the system if there is any fault during failure on DC side. A very crucial part of SPV system as there should be adequate protection on DC side. The DCDB incorporates isolatorBreaker to switch off the system during fault, there is a meter which tells you exact PV array voltage and current you are getting. It also have surge protection to save your system from any surges occurred due to fault or other phenomenon. These panel are customized as per the design of the solar plant.It is Used where the DC current rating is very high and incoming and outgoing of the DC current is need to be fused. High Quality DC BusmanEq fuses are used for incoming and outgoing through Buss bar. Surge Protection is provided in this panel in order to absorb excess surges in the system. Outdoor Type panels are also available- Picture ENAM securities outdoor panel

PCCMCC panels are made up of 1416 SWG CRCA material semi bolted structure firmly supported. Ensures desired breaking capacities, temperature rise & IP protection. Enough Space for incoming & outgoing Cable termination. Outgoing terminals are stud type as standard practice. All starters are Type Two Co-ordinated. CT terminals, Cable Alley Illumination Lamp, Space Heaters with Thermostats are standard features of our Panel boards.

All boards are combination of 14 & 1618 SWG sheet steel, free standing, extensible, totally enclosed, dust tight, vermin-proof cubicle, flush dead front and of modular construction suitable for 3 phase 415V 4 wire 50 Hertz system TN-S neutrals grounding. All boards are accessible from the front or as shown on Drgs and specified in the equipment data sheet, considering ease of maintenance of switch fuses, bus bars, cable terminations, meters etc. Cables entries can be both from top as well as bottom. All panels are CNC machine pressed with punched openings for meters etc. mounted on a 75mm high base channel frame. All sheet steel are made rust free through a process of degreasing, derusting, phosphating, activation etc. The panels are finished with powder coating of approved color. Engraved plasticaluminum labels are provided indicating the feeder details, and capacity and danger signs. The boards accommodate air insulated bus bars, ACB, MCCBs, SF units with HRC fuses, starters, meters, relays, contactors etc. are arranged in suitable tiers. The switch board are fully compartmentalized in vertical tiers housing the feeder switches in totally enclosed independent compartments. Each compartment is self- sufficient with switch unit, fuses, contactors, relays, indicating lamps and optionally inter-locked door with facility for padlocking. Each switch or MCCB or ACB will have provision for locking in the OFF position for life safety. Each feeder will terminate in an independent labelled terminal block. All power terminals above 16 sq mm are stud or bus bar type. All terminations are shrouded in an approved manner.

Fully compartmentalized, Drawout Modules are with-drawable with 3, distinct position viz Test, Service 8 Isolation, Drawout Modules of same size are fully interchangeable, Totally enclosed, vermin-proof & dust proof Vertical Busbar system, Automatic safety shutter for the vertical bus-bar, Main bus-bars are easily approachable from the top, Self-aligning & self-disconnecting power &auxiliary Control contacts, Vertical bus-bars are provided with contact Element for Drawout contacts, Spring Loaded Earth Contacts, Swivelling lever- guide for easy withdrawal of the modules without any additional tools, Feeder & cable alley doors open in opposite, Feeder & cable alley doors open in opposite.