This is a double walled serological bath with outer and inner wall made of stainless steel. The gap between the walls is filled with glasswool to minimize loss of temperature. A thermostat, at any point from 50C, controls the temperature automaticallyabove room temperature to 600C with an accuracy of + 0.50C and operates on single phase AC current. A built-in pilot lamp is also provided indicate the working of thermostat.Kahn racks to hold 40 tubes, are available at extra cost. The racks are made of stainless steel or brass.

Double walled construction, inner and outer chamber made of stainless steel with concentric rings and lids, with thermostatic control.Temperature range: 50C above ambient to 950CAccuracy: + 20CThe bath can be raised to boiling temperature with thermostat set at maximum.

Universal Water BathConstruction :

This water bath made from single wall made of stainless steel. It is designed to meet almost all requirements of Pathological, Microbiological, Chemical, Physical and other Laboratories.

Made of stainless steel with built in constant level arrangement, concentric rings and stainless steel lid Suitable for use on 230 Volts AC single phase supply.

Rectangular Water Bath

Single walled made of stainless steel with concentric rings and a lid are provided on hole. The bath has a built-in constant level arrangement.Suitable for use on 230 Volts AC single phase supply

For annealing, pre-heating, baking or any other heat processing where overhead handling equipment is used. Temperatures to 5250C. Full opening door exposes entire workspace for easy loading. Constructed for long hard continuous use. Ideal for severs service applications - load capacities up to 4000 lbs

STANDARD FEATURES

Controls

• Digital, microprocessor based, thermocouple actuated, indicating temperature controller
• Modulating burner on gas ovens.
• Motor control pushbuttons and on off heat switch
• Easy-to-see pilot lights

Safety Equipment - electric Oven

• Adjustable, thermocouple actuated, manual reset excess temperature controller
• Separate heating element control contactors
• Recirculating blower air flow safety switch

Safety Equipment - Gas Oven

• Adjustable, thermocouple actuated, manual reset excess temperature controller.
• Electronic flame safeguard protection
• Powered forced exhauster for combustion venting
• Exhauster air flow safety switch
• Recirculating blower air flow safety switch
• Purge timer
• High gas pressure switch
• Low gas pressure switch
• Latch-type manual reset main gas valve
• Testing device to test tight closure of main gas valve
• Solenoid blocking valve up to 400, 000 BTU/HR heat input; motorized backup valve and vent valve over 400, 000 BTU/Hr

Construction

• Adjustable patented opposed louvers on full coverage supply and return ductwork
• Automatic air operated door
• " steel plate top prevents loading damage
• Wear bars at sides of workspace
• Reinforced floor with removable grate
• 10 lbs./cf. density industrial rockwool insulation
• Aluminized steel interior
• Aluminized steel exterior with enamel finish
• Brushed stainless steel control panel face
• Adjustable fresh air intake and exhaust dampers
• High temperature door gasket with stainless steel spring insert
• All welded construction
• Low profile minimizes interference with loading equipment
• 1 year limited warranty

Every oven fully assembled and individually factory tested

Gas Models

- 1, 000 BTU natural gas at 6" water column pressure, 1" NPT inlet- Other gas characteristics availableControl panel as detailed above and safety devices as listed on the front of this bulletin. Automatic preignition purge period and pushbutton electric ignition contributes to ease of operation. Modulating gas burner is protected with electronic flame safety relay.These electric or gas ovens come in four sizes. They feature full horizontal airflow with adjustable patented opposed louvers for balanced airflow. The horizontal airflow pattern allows heated air to pass between stacked parts for uniform heating. High volume recirculating blowers are specifically designed for heating heavy loads.The removable grating on the oven floor protects the oven from impact during loading and distributes concentrated loads across the entire oven floor. The grating allows for air movement beneath the work for uniform processing.The LA and LC series have the heat chamber located to the rear of the workspace. ON the LB and LD Series, the heat chamber is located to the right side of the workspace to position the supply and return ductwork at the front and rear of the workspace respectively. This provides the shortest distance between ducts, which minimizes the temperature differential across the workspace.1000oF Models Only.

Insulated with 2" of 10500C insulating block backed up with 6750C industrial rockwool. 16 gauge aluminized steelwork space interior; 304 stainless steel heat chamber interior with stainless steel recirculating blower. Gas models include stainless steel exhauster.

ADDITIONAL EQUIPMENT AVAILABLE

• Programmable Temperature Controller, microprocessor based, digital indicating, thermocouple actuated, in lieu of standard controller.PTC3
• Recording Thermometer, thermocouple actuated, 24-hour, 10" diameter circular chart used in conjunction with standard controller.RT
• Programmable Recording Temperature Controller, microprocessor based, thermocouple actuated digital display, 24-hour, 10" diameter circular chart, in lieu of standard controller.PRTC3
• Digital Timing System, incorporated into standard temperature controller, 99 hour 59 minute range, starts timing when temperature reaches set point and shuts down oven at end of set time.DTS3
• Shut Down Timer, with continuous "hold" feature.1, 5, 10 or 30 hour range.SDT
• Batch Timer, for uniformly timing batch operations. Continuous alarm with door interlock; alarms at end of preset time period until door is opened or timer reset. 1, 5, 10 or 30 hour range.BT
• Automatic Door Switch turns off blower and heat when door is opened. Restores blower and heat on electric models blower only on gas models when door is closed.
• Powered Forced Exhausters

Whether in biotechnology, zoology & botany, whether in the pharmaceutical, cosmetic, food industry, or medicines, test at temperatures between room temperature & 0C are gaining importance. Here it is not only a question of excellent thermosetting accuracy but only a unrestricted time - dependent programming, of optimum, reproducibility & of documentation of the important test processes. In close co-operation with discerning users we have included these set new standards but also impress with a particularly high level of functionality.

CONSTRUCTION

The outer cabinet & inner chamber is manufactured from High Quality Polished Stainless Steel & regular models from quality mild steel finished with hardwearing powder coated. The cabinet is insulated with best quality fiber glasswool or polyurethane foam.

Double walled insulated door allows full access to the working chamber

HEATING AND COOLING

Heating is achieved by Low Surface Temperature Heaters. And they are located in side duct close to circulation fan. Hermetically sealed compressor coupled with evaporation coil and fan cooled condenser provides cooling below ambient temperature.

CONTROL SYSTEM

State of the Art Microprocessor based temperature controller controls temperature. Temperature is independently sensed by PT-100 Sensor. Microprocessor takes care of any overshooting or undershooting of temperature. Control system also controls automatically cooling and heating devices i.e. Heaters and Compressors. Cyclic Temperature Programming is also available as an option. The Controller Optionally allows taking printouts of temperature with real time clocks.

AIR CIRCULATION

A powerful fan located in the side duct of the working chamber re-circulates the internal atmosphere. A perforated false floor ensures an even vertical airflow throughout the working chamber. The air traveling upwards is extracted by a Fan and is guided through the side duct comprises of an electric heater, a heat exchanger (cooling coil). Day - Night Simulation

This is a double walled serological bath with outer and inner wall made of stainless steel. The gap between the walls is filled with glasswool to minimize loss of temperature. A thermostat, at any point from 50C, controls the temperature automaticallyabove room temperature to 600C with an accuracy of + 0.50C and operates on single phase AC current. A built-in pilot lamp is also provided indicate the working of thermostat.Kahn racks to hold 40 tubes, are available at extra cost. The racks are made of stainless steel or brass.

Double walled construction, inner and outer chamber made of stainless steel with concentric rings and lids, with thermostatic control.Temperature range: 50C above ambient to 950CAccuracy: + 20CThe bath can be raised to boiling temperature with thermostat set at maximum.

Universal Water BathConstruction :

This water bath made from single wall made of stainless steel. It is designed to meet almost all requirements of Pathological, Microbiological, Chemical, Physical and other Laboratories.

Made of stainless steel with built in constant level arrangement, concentric rings and stainless steel lid Suitable for use on 230 Volts AC single phase supply.

Rectangular Water Bath

Single walled made of stainless steel with concentric rings and a lid are provided on hole. The bath has a built-in constant level arrangement.Suitable for use on 230 Volts AC single phase supply

For annealing, pre-heating, baking or any other heat processing where overhead handling equipment is used. Temperatures to 5250C. Full opening door exposes entire workspace for easy loading. Constructed for long hard continuous use. Ideal for severs service applications - load capacities up to 4000 lbs

STANDARD FEATURES

Controls

• Digital, microprocessor based, thermocouple actuated, indicating temperature controller
• Modulating burner on gas ovens.
• Motor control pushbuttons and on off heat switch
• Easy-to-see pilot lights

Safety Equipment - electric Oven

• Adjustable, thermocouple actuated, manual reset excess temperature controller
• Separate heating element control contactors
• Recirculating blower air flow safety switch

Safety Equipment - Gas Oven

• Adjustable, thermocouple actuated, manual reset excess temperature controller.
• Electronic flame safeguard protection
• Powered forced exhauster for combustion venting
• Exhauster air flow safety switch
• Recirculating blower air flow safety switch
• Purge timer
• High gas pressure switch
• Low gas pressure switch
• Latch-type manual reset main gas valve
• Testing device to test tight closure of main gas valve
• Solenoid blocking valve up to 400, 000 BTU/HR heat input; motorized backup valve and vent valve over 400, 000 BTU/Hr

Construction

• Adjustable patented opposed louvers on full coverage supply and return ductwork
• Automatic air operated door
• " steel plate top prevents loading damage
• Wear bars at sides of workspace
• Reinforced floor with removable grate
• 10 lbs./cf. density industrial rockwool insulation
• Aluminized steel interior
• Aluminized steel exterior with enamel finish
• Brushed stainless steel control panel face
• Adjustable fresh air intake and exhaust dampers
• High temperature door gasket with stainless steel spring insert
• All welded construction
• Low profile minimizes interference with loading equipment
• 1 year limited warranty

Every oven fully assembled and individually factory tested

Gas Models

- 1, 000 BTU natural gas at 6" water column pressure, 1" NPT inlet- Other gas characteristics availableControl panel as detailed above and safety devices as listed on the front of this bulletin. Automatic preignition purge period and pushbutton electric ignition contributes to ease of operation. Modulating gas burner is protected with electronic flame safety relay.These electric or gas ovens come in four sizes. They feature full horizontal airflow with adjustable patented opposed louvers for balanced airflow. The horizontal airflow pattern allows heated air to pass between stacked parts for uniform heating. High volume recirculating blowers are specifically designed for heating heavy loads.The removable grating on the oven floor protects the oven from impact during loading and distributes concentrated loads across the entire oven floor. The grating allows for air movement beneath the work for uniform processing.The LA and LC series have the heat chamber located to the rear of the workspace. ON the LB and LD Series, the heat chamber is located to the right side of the workspace to position the supply and return ductwork at the front and rear of the workspace respectively. This provides the shortest distance between ducts, which minimizes the temperature differential across the workspace.1000oF Models Only.

Insulated with 2" of 10500C insulating block backed up with 6750C industrial rockwool. 16 gauge aluminized steelwork space interior; 304 stainless steel heat chamber interior with stainless steel recirculating blower. Gas models include stainless steel exhauster.

ADDITIONAL EQUIPMENT AVAILABLE

• Programmable Temperature Controller, microprocessor based, digital indicating, thermocouple actuated, in lieu of standard controller.PTC3
• Recording Thermometer, thermocouple actuated, 24-hour, 10" diameter circular chart used in conjunction with standard controller.RT
• Programmable Recording Temperature Controller, microprocessor based, thermocouple actuated digital display, 24-hour, 10" diameter circular chart, in lieu of standard controller.PRTC3
• Digital Timing System, incorporated into standard temperature controller, 99 hour 59 minute range, starts timing when temperature reaches set point and shuts down oven at end of set time.DTS3
• Shut Down Timer, with continuous "hold" feature.1, 5, 10 or 30 hour range.SDT
• Batch Timer, for uniformly timing batch operations. Continuous alarm with door interlock; alarms at end of preset time period until door is opened or timer reset. 1, 5, 10 or 30 hour range.BT
• Automatic Door Switch turns off blower and heat when door is opened. Restores blower and heat on electric models blower only on gas models when door is closed.
• Powered Forced Exhausters

Whether in biotechnology, zoology & botany, whether in the pharmaceutical, cosmetic, food industry, or medicines, test at temperatures between room temperature & 0C are gaining importance. Here it is not only a question of excellent thermosetting accuracy but only a unrestricted time - dependent programming, of optimum, reproducibility & of documentation of the important test processes. In close co-operation with discerning users we have included these set new standards but also impress with a particularly high level of functionality.

CONSTRUCTION

The outer cabinet & inner chamber is manufactured from High Quality Polished Stainless Steel & regular models from quality mild steel finished with hardwearing powder coated. The cabinet is insulated with best quality fiber glasswool or polyurethane foam.

Double walled insulated door allows full access to the working chamber

HEATING AND COOLING

Heating is achieved by Low Surface Temperature Heaters. And they are located in side duct close to circulation fan. Hermetically sealed compressor coupled with evaporation coil and fan cooled condenser provides cooling below ambient temperature.

CONTROL SYSTEM

State of the Art Microprocessor based temperature controller controls temperature. Temperature is independently sensed by PT-100 Sensor. Microprocessor takes care of any overshooting or undershooting of temperature. Control system also controls automatically cooling and heating devices i.e. Heaters and Compressors. Cyclic Temperature Programming is also available as an option. The Controller Optionally allows taking printouts of temperature with real time clocks.

AIR CIRCULATION

A powerful fan located in the side duct of the working chamber re-circulates the internal atmosphere. A perforated false floor ensures an even vertical airflow throughout the working chamber. The air traveling upwards is extracted by a Fan and is guided through the side duct comprises of an electric heater, a heat exchanger (cooling coil). Day - Night Simulation