Coil heaters are typically used in area which has a higher watt density requirement. The Basic construction of these heaters involves swaging of compacted MgO, Nickel Chromium wire into a Chrome Nickel steel tube. These heaters when swaged to provide maximum support for the resistance wire, eliminating the effects of vibration and shock.

• Standard stock size from 250 w to 1200 w
• Temp upto 750 deg C
• With J type or K type T/C
• Highly non corrosive
• Various cross sections available

• Hot runner nozzles and bushing
• Tube extrusion
• Pipe forming

These heaters are made of Nicrohome wire sealed inside a Steel tubular high temperature grade pipe, which is compacted along with high grade MGO allowing it to withstand high insulation resistance, later the element are brazed to a Cast Iron Flange/ Brass flange / S.S.Flange / and are provided with a Thermostat pocket, earthing terminal, & cap.

These heaters are designed to provide efficient heating which ensures that the Oil flash point is not achieved in case of non failure of temp. controller or sensor.

• Avaliable in s.s.304, s.s.316
• Incoloy, Sheathed elements, Brass
• S.S. or M.S. flanges available
• Lower watt density for effective heating
• Standard stock size available

• Furnances, Oil tanks, For fuel oil heating, oil circulating, for systems which supply hot oil to plastic & chemicals processes
• Oil jacketted kettles and similar equipments

Oil drum heater is heating on the surface of drum to make the concentration and viscosity of the liquid and coagulum inside decreased uniformly. In this way It will be easy to take out the liquid and coagulum in any season.

The flexible drum heater has an Inside Ni-Cr Alloy heating wires. Outside is silicon rubber insulation material for Fast heating and long working life. Ni-Cr Alloy heating wire is wound around the alkali-free fiber-glass. Main insulation material is silicon rubber which is of high heat-resistance and insulation. These drum heater is soft and flexible resulting in snug fit over the drums.

• Temperature controller on the surface of heating band
• The temperature range can be set between 30-150C normally
• Maxi heat-resistance 250C
• Suggested operating temperature < 200C
• Insulation resistance > 50M
• Dielectric strength: > 1500V /min
• Can be used on both HDPE and metal drums

• Fats
• Gelatin
• Glucose
• Grease
• Lubricating Oils
• Paints
• Petroleum Jelly
• Phenols
• Plastics
• Vegetable Oils
• Varnishes
• Waxes

We are offering immersion heaters.These are mainly for water, oil, alkaline, etc applications made as per customer requirement. The length and the wattage will vary as per the need.

Coil heaters are typically used in area which has a higher watt density requirement. The Basic construction of these heaters involves swaging of compacted MgO, Nickel Chromium wire into a Chrome Nickel steel tube. These heaters when swaged to provide maximum support for the resistance wire, eliminating the effects of vibration and shock.

• Standard stock size from 250 w to 1200 w
• Temp upto 750 deg C
• With J type or K type T/C
• Highly non corrosive
• Various cross sections available

• Hot runner nozzles and bushing
• Tube extrusion
• Pipe forming

These heaters are made of Nicrohome wire sealed inside a Steel tubular high temperature grade pipe, which is compacted along with high grade MGO allowing it to withstand high insulation resistance, later the element are brazed to a Cast Iron Flange/ Brass flange / S.S.Flange / and are provided with a Thermostat pocket, earthing terminal, & cap.

These heaters are designed to provide efficient heating which ensures that the Oil flash point is not achieved in case of non failure of temp. controller or sensor.

• Avaliable in s.s.304, s.s.316
• Incoloy, Sheathed elements, Brass
• S.S. or M.S. flanges available
• Lower watt density for effective heating
• Standard stock size available

• Furnances, Oil tanks, For fuel oil heating, oil circulating, for systems which supply hot oil to plastic & chemicals processes
• Oil jacketted kettles and similar equipments

Oil drum heater is heating on the surface of drum to make the concentration and viscosity of the liquid and coagulum inside decreased uniformly. In this way It will be easy to take out the liquid and coagulum in any season.

The flexible drum heater has an Inside Ni-Cr Alloy heating wires. Outside is silicon rubber insulation material for Fast heating and long working life. Ni-Cr Alloy heating wire is wound around the alkali-free fiber-glass. Main insulation material is silicon rubber which is of high heat-resistance and insulation. These drum heater is soft and flexible resulting in snug fit over the drums.

• Temperature controller on the surface of heating band
• The temperature range can be set between 30-150C normally
• Maxi heat-resistance 250C
• Suggested operating temperature < 200C
• Insulation resistance > 50M
• Dielectric strength: > 1500V /min
• Can be used on both HDPE and metal drums

• Fats
• Gelatin
• Glucose
• Grease
• Lubricating Oils
• Paints
• Petroleum Jelly
• Phenols
• Plastics
• Vegetable Oils
• Varnishes
• Waxes

We are offering immersion heaters.These are mainly for water, oil, alkaline, etc applications made as per customer requirement. The length and the wattage will vary as per the need.