S.S.Sanitary & Pipe Store

Saraswati Vihar, Delhi

The material that is used for the production complies with high quality standards and quality-proved by the experts. Also, we make sure that the raw material is sourced from the trusted places. Ductile Iron Pipes have higher tensile strength, yield strength, ductility and impact resistance which are the reasons why the use of Ductile Iron Pipes has grown up at a rapid rate over the last 50 years or so.

External Coatings :

• Metallic Zinc coating having an average mass of 130gm/sq.m with finishing layer
• Metallic Zinc-alloy coating having a minimum mass of 200 g/m2 with finishing layer
• Extruded polyethylene self adhesive tape wrapping at factory/at site
• Reinforced cement mortar coating having a nominal thickness of at least 5 mm
• Fusion bonded epoxy coating
• Polyurethane coating

Linings :

• Cement mortar lining & thicker mortar lining as per the customer requirement
• Cement mortar lining with seal coat
• Two pack of epoxy lining as a supplement to cement mortar lining
• Polyurethane lining
• We keep ready stock of K7 and K9 grade in our warehouse .

Standard : IS : 8329

Connection : Push On Joints

We manufacture Centrifugally Cast (Spun) Iron Pressure Pipes confirming to IS: 1536:2001. The Cast Iron Socket & Spigot pressure pipes reign supremacy over other types of pipes. Moreover C I S&S Pressure Pipes are usable as best carriers of :

• Water for Irrigation.
• Drinking and Industrial purposes.
• Sludge.
• Brines & Liquid in Chemical Industries.
• Crude & Refined Oil.
• Ash Handling.
• Plumbing etc.

Classification : Pipes have been classified in this standard as LA, A and B according to their thickness. Class LA pipes have been taken as basis for evolving the series of pipes. Class A allows a 10 percent increase in thickness over Class LA. Class B allows a 20 percent increase in thickness over Class LA. For Special uses, Classes C, D, or E may be derived after allowing corresponding increases of thickness of 30, 40 or 50 percent respectively.


Pressure Pipes Special Aspects :

• Ability to withstand high pressure.
• Inherent toughness.
• Resistant to Corrosion.
• Non-Absorbent.
• Higher Tensile Strength.
• Firm & easy jointing.
• Easy Machinability.
• Easy Handling & Laying.
• Low Maintenance Cost.
• Pressure Pipes Testing at Works

Mechanical Test : Mechanical tests shall be carried out, during manufacture. Tests for every four hours of production shall be conducted. The results obtained shall be taken to represent all the pipes of all sizes made during that period.

Details :

• Model Number - Class LA , A , B , C , D
• Material - Cast Iron
• Diameter - 80mm to 600mm
• Thickness - As Per Is Standards
• Length - As per Customer Requirements
• Standard - IS : 1536

We stringently make complete arrangements for the vigil examination of the inputs used for the products. By this, we are capable of bringing forth reliable products that are presented after complete inspection and examination by the experts.

Specifications :

• Pipes & Fittings - As per IS 15905 Marked
• Stainless Steel Coupling with EPDM Rubber - ASTM - 1277, IS - 15905.
• Stainless steel Coupling are use for joining

Uses :

• Cast Iron Hubless Pipes & Fittings are used in Gravity Drainage System for following purposes
• Soil Waste Ventilation Rain Water

Range & Nominal Sizes :

• Hubless Pipes & Fittings are manufactured and available in complete range as per product catalouge and in following nominal sizes, ( pipe length : 3000 mm max.)
• 50mm 75 mm 100 mm 150 mm 200 mm 250mm 300mm

Material : Cast Iron used for manufacturing Hubless Pipes & Fittings confirms to: IS 210, ISO 185 & grade FG 200.

Important Features :

• Durable & Life Long
• High Impact Strength
• Longer Length, Less Joints
• Easy To Install
• Smooth Finish & Elegant Look
• No Leakages, No Blockages
• Fire Proof & Temperature Resistant
• Cost Effective
• Easy Availability
• Environment Friendly

Details :

• Type - Hubless
• Material - Cast Iron
• Diameter - 50MM TO 300MM DN
• Thickness - As per is Standards
• Length - 300MM TO 3000MM
• Standard - IS 15905

We are staffed with a team of professionals who hold immense knowledge in this domain. We promise to deliver the orders within the postulated time frame as we are backed by excellent logistics facility. The Pipes are manufactured in the standard length of 3M, cut pipes are also available Pipes and Fittings are coated internally by Black Bitumen Paint and externally by Red Primer and Anti rust Enamel Paint.

Material : Grey Cast Iron

Usage :

• Discharge of Soil and Waste
• Discharge of Rainwater
• Ventilation

Details :

• Type - Centrifugally Spun Cast
• Material - Cast Iron
• Length - 300MM TO 3000MM
• Application - Plumbing
• Standard - IS : 3989
• Diameter - 50MM TO 300MM DN
• Produced in 50mm, 75mm, 100mm, 150mm, 200mm, 250mm, 300mm nominal diameter

The company has installed all the in-house facility wherein we maintain a large stock for meeting quick and massive requirements of the clients. Sternly packed and delivered safely to the customers' provided address and that too in the committed time span.

Range :

• Size - 80 mm to 1000 mm
• Length - up to 5.5m. available in mix length.
• IS 7181 - Ci Flanges are casted with the pipe itself.
• These pipes are manufactured to a maximum of 2.75 mtrs length only.
• The pipes are internally & externally coated with Bitumen paint.

Application :

• Ash Disposal in Power Plants.
• Sand Stowing operations in Mines.
• Fire Fighting Systems.
• Sugar Industries for Spray pond, SO2 piping & Injection Piping.
• For Laying in Hilly Areas / Slopes, even exceeding the Angle of Repose.
• Treatment Plants-Potable Water, Effluent and Waste Treatment.
• Chemicals Industry application for cooler pipes for conducting various chemical fluids like Sulphuric Acid, Brines, Alkalies, etc.
• Cast Iron Double Flanged Pipes are widely used in Soda Ash Plants, Fertilizer Plants, Sulphuric Acid Plants.
• Water Supply - Overhead Water Tanks, Pumping stations, Underground Mains, River Crossing, Hill Tracks, Sandy area, etc.
• Vertical Pipe Lines: for overhead Tanks / Elevated Service Reservoirs (EDR'S).

• Disengagement Requirements :
  • Application where pipelines are disengaged / dismantled for cleaning like in treatment plants for water, Effluent, Sewage and pump houses.
  • Temporary installations, applications where pipelines are transferred. from one location to other - require Flange Pipes like temporary pipelines required for Dewatering mines or heavily inundated areas.

Over Ground and & Exposed Installation : Flanged Pipes are most suitable for over ground pipelines like portions of Pipelines on Pillars / Pedestals for Rivers / Canal or Road crossing.

Type : Flanged

Material : Cast Iron

Keeping pace with the contemporary market trends, we ensure on-time and safe delivery of the orders. Our raw materials are essential bottleneck assets and thus these are carefully selected by our expert quality auditors after checking against varied quality parameters.

Range :

• Size - 80 mm to 1000 mm
• Length - up to 5.5m. available in mix length.
• IS 7181 - Ci Flanges are casted with the pipe itself.
• These pipes are manufactured to a maximum of 2.75 mtrs length only.
• The pipes are internally & externally coated with Bitumen paint.

Application :

• Ash Disposal in Power Plants.
• Sand Stowing operations in Mines.
• Fire Fighting Systems.
• Sugar Industries for Spray pond, SO2 piping & Injection Piping.
• For Laying in Hilly Areas / Slopes, even exceeding the Angle of Repose.
• Treatment Plants-Portable Water, Effluent and Waste Treatment.
• Chemicals Industry application for cooler pipes for conducting various chemical fluids like Sulphuric Acid, Brines, Alkalies, etc.
• Cast Iron Double Flanged Pipes are widely used in Soda Ash Plants, Fertilizer Plants, Sulphuric Acid Plants.
• Water Supply - Overhead Water Tanks, Pumping stations, Underground Mains, River Crossing, Hill Tracks, Sandy area, etc.
• Vertical Pipe Lines: for overhead Tanks / Elevated Service Reservoirs (EDR'S).

• Disengagement Requirements :
  • Application where pipelines are disengaged / dismantled for cleaning like in treatment plants for water, Effluent, Sewage and pump houses.
  • Temporary installations, applications where pipelines are transferred. from one location to other: require Flange Pipes like temporary pipelines required for De-Watering mines or heavily inundated areas.

Over Ground and & Exposed Installation : Flanged Pipes are most suitable for over ground pipelines like portions of Pipelines on Pillars / Pedestals for Rivers / Canal or Road crossing .

Type : Flanged

Material : Cast Iron