GST : 07FEEPS7094H1ZW
Verified
Write a Review
Our Products
Measuring Instruments
2 Products available
ASTM D6926, D5581; AASTHO T245 (only for UTAS-0071); BS-598
The UTAS-0670 and UTAS-0676 Marshall Manual Assemblies are used to prepare Marshall specimens manually.
The Compaction Assemblies consist of a Marshall Compaction Hammer and a Wooden Compaction Pedestal. The Pedestals are supplied complete with a steel plate, a mould holder and a hammer guide.
UTAS-0667 and UTAS-0668 Marshall Steel Blocks are used for initial heating of the foot of compaction hammer should be ordered separately.
Integral Proving Ring
The Proving Rings are made up of special steel, carefully forged to give maximum strength and machined to give high sensitivity commensurate with stability, ensuring long life and accuracy. All proving rings are integral type viz. the loading (outside) bosses are forged integral with the ring body. This ensures that there is no possibility of abutment shift and consequent loss of accuracy in reading that always exists with bolted abutments. Repeatability in these Proving Rings is as stipulated in IS:4169.The rings are supplied complete with dial gauge and Works Calibration Chart, individually packed in polished wooden boxes. National Physical Laboratory (NPL), (India)/ National Council for Cement & Building Material (NCCBM )Calibration can also be arranged for any proving ring at an additional cost. Proving rings to meet special requirements are also available on request.Separate polished and ground pair of Loading Pads for Compression Proving Rings and pair of Shackles for Tension Proving Rings are provided to suit each proving ring.
Models available:
Additional Information:
Packaging Details : Compression Proving Ring, 0.5 kN
Compression Proving Ring, 1.0 kN
Compression Proving Ring, 2.0 kN
Compression Proving Ring, 2.5 kN
Compression Proving Ring, 4.0 kN
Compression Proving Ring, 5.0 kN
Compression Proving Ring, 10.0 kN
Compression Proving Ring, 15.0 kN
Compression Proving Ring, 20.0 kN
Compression Proving Ring, 25.0 kN
Compression Proving Ring, 30.0 kN
Compression Proving Ring, 40.0 kN
Compression Proving Ring, 50.0 kN
Compression Proving Ring, 100 kN
Compression Proving Ring, 200 kN
Compression Proving Ring, 300 kN
Compression Proving Ring, 500 kN
Compression Proving Ring, 1000 kN
Compression Proving Ring, 2000 kN
Compression Proving Ring, 3000 kN
Stainless Steel Laboratory Scoops is made with one pointy end and one blunt end. This type of functional design allows for digging out and handling of small quantities of substances. Stainless Steel Laboratory Scoops is used for accurately dispensing powders and granules hygienically in the laboratory. It is suitable for any hygienic application.
Stainless Steel Laboratory Scoops is made of superior grade stainless steel which is resistant to corrosion, chemical abrasion and also easy to use and handle as all its parts are welded by Argon welding. Its well-designed look gives elegant and aesthetic finish.
Steel Laboratory Scoops is 100% quality checked and tested since it is manufactured by the latest well-equipped CNC machinery and latest techniques like cutting and bending and for any other structural flaws by our highly qualified professional staff according to Indian and international industry standards guidelines.
At S.N Scientific Solution, by using cutting edge industrial manufacturing methods and quality controls through production sections we confirm that customers get prime Stainless Steel Laboratory Scoops custom-made to client's requirements. Each pharmaceutical product is developed as per the ISO standards and pharmaceutically is safe and hygienic.
Procter Mould 100mm 150mm With Rammer Powdeer Coated & Zink.
The Pycnometer is used for determination of specific gravity of soil particles of both fine grained and coarse grained soils. The determinination of specific gravity of soil will help in the calculation of void ratio, degree of saturation and other different soil properties.
Manual Flow Table for determining consistency (flow) and preparing mortars of standard consistency for testing. The Manual Flow Table provides reliable results and is recommended for applications where strict adherence to standards is not essential. Flow Table has 10in (254mm) diameter rigid cast bronze table supported in cast iron frame. Base and special drive motor bracket mount to the concrete pedestal. Concrete pedestal not included. Included cast bronze flow mold has 2.75/4in (70/102mm) top/bottom ID with a collar.
Features:
SizeDiameter of cylinderCapacity of Cylinder Small 115 3 Liters Medium 165 9 Liters Large 215 16.5 Liters
The objective of the test method is to measure the working and ultimate capacities of rock bolt anchors. The system comprises of a central hole jack, hand pump with a load gauge, directional control value (only for central hole jacks above the capacity of 500 kn), flexible hose pipe 5 mts, truss high tensile bolts with coupling. In general the pull out force is indicated on the load gauge, however a load cell with digital indicator can be used to measure the pull out load. Arrangement is provided for fixing the dial gauge for estimating deflection against the load. These are used to measure the working and ultimate capacities of rock bolt anchors. Further, our products comprises of a central hole jack, hand pump with load gauge, directional control valve and only for central hole jacks above the capacity of 500kN, flexible pipes, truss high tensile test rod with coupling.
The apparatus of the aggregate impact value test consists of: A testing machine weighing 45 to 60 kg and having a metal base with a plane lower surface of not less than 30 cm in diameter. Level and plane concrete floor of minimum 45 cm thickness are used to support it. The base of the machine should also have provisions for fixing its base. A cylindrical steel cup of internal diameter 102 mm, depth 50 mm and minimum thickness 6.3 mm. A metal hammer or tup weighting 13.5 to 14.0 kg the lower end is cylindrical in shape, is 50 mm long, 100.0 mm in diameter, with a 2 mm chamfer at the lower edge and case hardened. The hammer is arranged in such a way that it should slide freely between vertical guides and be concentric with the cup. It is arranged that the free fall of the hammer should be within 380±5 mm. A cylindrical metal measure having an internal diameter of 75 mm and depth 50 mm for measuring aggregates. One end rounded tamping rod 10 mm in diameter and 230 mm long. A balance of capacity not less than 500 g, and readable and accurate up to 0.1 g.
Product Description in this machine the mould is mounted on the vibrating platform with having frequency of 12, 000 ± 400 vibrations per minute. The entire assembly is operated by the revolving shaft with eccentric mechanism and the platform is attached with four matched springs.
Specific gravity is the basis of methods used throughout history to concentrate ores. Panning, jigging, shaking, spiral separation, and heavy-medium separation are among the methods that depend on differences in specific gravity to obtain concentrated ore.
With an objective to fulfill the needs of the patrons, we are engaged in manufacturing, supplying and wholesaling Cube Cutter and Hammer. These products are manufactured under the supervision of experienced professionals, who strictly follow industry laid guidelines. Our professionals utilize optimum quality material to manufacture these products offered by us. Along with this, our experts keeps vigil on every stage of production to maintain higher standards of quality. In order to offer qualitative products, our professionals stringently examine these products on different parameters to ensure their flawlessness and then forward for the final dispatch to the patrons. To fulfill the diversified requirements of the clients, all these products are available in various specifications as well as in customized range. Core cutter apparatus is used for determination of dry density of soil. Mild steel cylindrical cutter is used to extract the cylindrical sample of soil with the help of dolly and hammer.
Specifications:
Cylindrical Steel Cutter : 100 mm Pipe ID / wall thickness 3mm / 130 mm long / beveled at one end
M.S.Rammer : Solid mild steel bar Diameter 140 mm & 75 mm height screwed centrally 25 mm bright MS bar.
Total height approximately 900 mm of both MS bar
Steel Dolly : 100 mm I.D. Pipe , 25 mm height , wall thickness 7 mm beveled to fit on steel cutter
Specification: Used for the compaction of concrete samples in a mould. Generally the vibratory hammer is found to be a much faster & quicker method as compared to impact hammering. The vibratory hammers are supplied with 1 tamping feet & 1 shank.
Used for determination of the relative quantity of mixing water that will bleed from a sample of freshly mixed concrete.
Dimensions : 290 x 255 x 350 mm
Weight (approx.) : 40 kg
Mortar Mixer has been specifically designed to mix cement paste and mortars to standard requirements. The machine can be operated in either automatic or manual mode. The mixer uses an elliptical mixing motion for thorough and efficient mixing and includes microprocessor control of the speed and mixing program. Specifications Speed (rpm)PaddleMixing Head Low 140 ± 5 62 ± 5 High 285 ± 10 125 ± 10 Rated power 180 W Bowl capacity 5 liters Weight 54 kg Dimension (LxWxH) 530 x 350 x 580 mm
Mr. Sajid Saifi (S.N. Scientific Solution)
Prop.No-K-1/M-24-B-8 Gali No-7 Anand Parbat Industrial Area Delhi-110005
Share us via
View Contact Number 
