Hand Operated:Proving ring type. Comprises of a hand operated load frame, cap. 30KN (3000 kgf.) screw jack for loading, handle and strain dial gauge bracket, adaptor for proving ring, conical seats and male/female coning tools for 38 mm dial samples. Supplied without proving ring and dial gauge.

Motorized: Comprises a screw operated load frame capacity 50 KN (5000 kgf.) with a gear box and motor drive giving 1.25, 1.5 and 2.5mm/min, rates of strain, pair of cone seating, adaptor for proving ring and strain dial gauge bracket. Supplied with one pair of male/female coning tools for 38 mm dia samples but without proving ring and dial gauge. Suitable for operating on 230 volts, single phase AC Supply. 

Dorry Abrasion Testing Machine that we provide is used for determining the resistance of aggregate to wear by abrasion. If there is an inadequate abrasion resistance of road-surfacing aggregates that it means an early loss of the texture depth, which is basically required for maintaining the high-speed skidding resistance. Dorry Abrasion Testing Machine features a disc rotating about a shaft that is connected to a reduction gearbox fixed to a motor. That disc rotates at 28-30 R.P.M. It features two conical hoppers, two holes for specimens and two containers with weights. It is ideal to be operated on 220 volts, 50 cycles, and A.C. supply.

We are offering Compression Testing Machine which operates by hydraulic transmission of load from the test specimen to separately housed load indicator. Our Compression Testing Machine is specifically designed to enable high accuracy testing with economy, speed and versatility. The machine features motor driven geared shafts, control panel, power pack, hydraulic controls, load indicator system and pendulum dynamometer. Its loading accuracy is as high as + 1%. Also, it facilitates straining at variable speeds to suit a wide range of materials. 

Available in :

• 100/150/200 ton hand operated.
• 100/150/200 ton Electric operated.
• 100/150/200 ton Electric operated with digital display.

Our Ductility Testing Machine is available with refrigeration system and micro-processor based digital temperature controller. Ductility Testing Machine features built-in refrigeration system that works at below ambient temperature. The Machine will operate at 27°C with control accuracy of ± 0.5°C as per the requirement of IS. It features a built-in refrigeration system that operates at below ambient temperature of up to 10°C in tropical conditions. Ductility Testing Machine consists of water bath with a heater and a circulating pump in order to maintain uniform temperature of water. The temperature is controlled by using dual display microprocessor based auto-tuning PID Digital Temp. Indicator cum controller. Ductility Testing Machine features control switches for stirrer, motor, heater and indicator lamps on the water bath. The machine is completed with three briquette molds and one base plate.

Our Deval Attrition Testing Machine is used for assessing the resistance of aggregate to wear by abrasion. Deval Attrition Testing Machine that we offer features two hollow cylinders closed at one end. The cylinders are mounted at an angle of 30º along with the axis of rotation of the shaft, which rotates at 30-33 R.P.M. It is further provided with tight fitting covers at either ends. Our Deval Attrition Testing Machine is completed with abrasive charges that consist of 12 Nos. Deval Attrition Testing Machine is ideal for operation at 440 volts, 3 phases, 50 cycles, and A.C. supply.

Flexure Testing Machine is used in numerous industries for testing 40mm x 40mm x 160mm mortar specimens for flexural strength by single point loading. It is designed with motorized and mechanical unit. With adjustable speed option, our Flexure Testing Machine also features flexure test attachment for keeping the specimen in position. The Flexure Testing Machine operates on 230 Volts, single phase, 50 cycles A.C. Further, we provide Flexure Testing Machine with proving ring of capacity 500 Kn.

Details :

• The speed is adjusted so that the load increase on the specimen is between 4 to 6 kg/sec
• A flexure test attachment for keeping the specimen in position is also supplied
• This consists of two rollers 10mm. diameter and spaced 100mm apart, and a third roller of the same diameter equidistant from the first two

Hand Operated:Proving ring type. Comprises of a hand operated load frame, cap. 30KN (3000 kgf.) screw jack for loading, handle and strain dial gauge bracket, adaptor for proving ring, conical seats and male/female coning tools for 38 mm dial samples. Supplied without proving ring and dial gauge.

Motorized: Comprises a screw operated load frame capacity 50 KN (5000 kgf.) with a gear box and motor drive giving 1.25, 1.5 and 2.5mm/min, rates of strain, pair of cone seating, adaptor for proving ring and strain dial gauge bracket. Supplied with one pair of male/female coning tools for 38 mm dia samples but without proving ring and dial gauge. Suitable for operating on 230 volts, single phase AC Supply. 

Dorry Abrasion Testing Machine that we provide is used for determining the resistance of aggregate to wear by abrasion. If there is an inadequate abrasion resistance of road-surfacing aggregates that it means an early loss of the texture depth, which is basically required for maintaining the high-speed skidding resistance. Dorry Abrasion Testing Machine features a disc rotating about a shaft that is connected to a reduction gearbox fixed to a motor. That disc rotates at 28-30 R.P.M. It features two conical hoppers, two holes for specimens and two containers with weights. It is ideal to be operated on 220 volts, 50 cycles, and A.C. supply.

We are offering Compression Testing Machine which operates by hydraulic transmission of load from the test specimen to separately housed load indicator. Our Compression Testing Machine is specifically designed to enable high accuracy testing with economy, speed and versatility. The machine features motor driven geared shafts, control panel, power pack, hydraulic controls, load indicator system and pendulum dynamometer. Its loading accuracy is as high as + 1%. Also, it facilitates straining at variable speeds to suit a wide range of materials. 

Available in :

• 100/150/200 ton hand operated.
• 100/150/200 ton Electric operated.
• 100/150/200 ton Electric operated with digital display.

Our Ductility Testing Machine is available with refrigeration system and micro-processor based digital temperature controller. Ductility Testing Machine features built-in refrigeration system that works at below ambient temperature. The Machine will operate at 27°C with control accuracy of ± 0.5°C as per the requirement of IS. It features a built-in refrigeration system that operates at below ambient temperature of up to 10°C in tropical conditions. Ductility Testing Machine consists of water bath with a heater and a circulating pump in order to maintain uniform temperature of water. The temperature is controlled by using dual display microprocessor based auto-tuning PID Digital Temp. Indicator cum controller. Ductility Testing Machine features control switches for stirrer, motor, heater and indicator lamps on the water bath. The machine is completed with three briquette molds and one base plate.

Our Deval Attrition Testing Machine is used for assessing the resistance of aggregate to wear by abrasion. Deval Attrition Testing Machine that we offer features two hollow cylinders closed at one end. The cylinders are mounted at an angle of 30º along with the axis of rotation of the shaft, which rotates at 30-33 R.P.M. It is further provided with tight fitting covers at either ends. Our Deval Attrition Testing Machine is completed with abrasive charges that consist of 12 Nos. Deval Attrition Testing Machine is ideal for operation at 440 volts, 3 phases, 50 cycles, and A.C. supply.

Flexure Testing Machine is used in numerous industries for testing 40mm x 40mm x 160mm mortar specimens for flexural strength by single point loading. It is designed with motorized and mechanical unit. With adjustable speed option, our Flexure Testing Machine also features flexure test attachment for keeping the specimen in position. The Flexure Testing Machine operates on 230 Volts, single phase, 50 cycles A.C. Further, we provide Flexure Testing Machine with proving ring of capacity 500 Kn.

Details :

• The speed is adjusted so that the load increase on the specimen is between 4 to 6 kg/sec
• A flexure test attachment for keeping the specimen in position is also supplied
• This consists of two rollers 10mm. diameter and spaced 100mm apart, and a third roller of the same diameter equidistant from the first two