Ryder minimum pressure valve is designed for use in oil-injected screw compressor and vane compressors. it ensures the necessary oil pressure for cooling and rotary-lubricating of the compressor is maintained. the minimum pressure valve is a spring loaded type and a built in non-return valve. ryder valve gives maximum life to the air-oil separator. 1", 1-12", 2", 2-12" BSPBSPTNPT, Nominal bore: 25, 38, 50, 62mm

We make suction control 3" and 4" size suction controller inlet. Ryder suction controller controls the compressor capacity. At start up the valves open until a control signal is applied to close the valve. During normal operation, the valve opens and closes in response to the control signal to meet the downstream air demands. At shut down a check valve stays close to prevent back through the compressor.

Specifications :

• Straight through design for low pressure drop.
• PTFE valve seat for tight seal
• One-piece housing with square flange mounting
• Side ports for pressure taps
• Operating pressure up to 200psi

Foot Control Valve is an on-off valve which is operated by foot. The valve body and the foot rest is made up of aluminium alloy and the piston is spring loaded one. It is in the closes condition by means of the spring and when the foot rest is pressed the valve opens and the air to the operation.

This is a Electro Magnetic Valve and each valve is connected to different function of the component in the vehicle or machine. It is a three way two position valve and operate in 12V DC Solenoid valve. These Electro Magnetic Valves are made from excellent quality raw materials. Our Electro Magnetic Valves can be availed at industrial leading price.

Specifications :

Ryder Non Return Valve has a very low opening pressure and low differential for closing even at high operating pressure. The unit locks effectively in reverse directions at pressure differential as low as 0.1 kgf/cm2 . The unit is equally efficient in operation while handling fluids under pressure or vacuum. This valve is a self-aligning unit and hence can be mounted/ fitted in any position. However horizontal position is more desirable

Specifications :

Ryder minimum pressure valve is designed for use in oil-injected screw compressor and vane compressors. it ensures the necessary oil pressure for cooling and rotary-lubricating of the compressor is maintained. the minimum pressure valve is a spring loaded type and a built in non-return valve. ryder valve gives maximum life to the air-oil separator. 1", 1-12", 2", 2-12" BSPBSPTNPT, Nominal bore: 25, 38, 50, 62mm

We make suction control 3" and 4" size suction controller inlet. Ryder suction controller controls the compressor capacity. At start up the valves open until a control signal is applied to close the valve. During normal operation, the valve opens and closes in response to the control signal to meet the downstream air demands. At shut down a check valve stays close to prevent back through the compressor.

Specifications :

• Straight through design for low pressure drop.
• PTFE valve seat for tight seal
• One-piece housing with square flange mounting
• Side ports for pressure taps
• Operating pressure up to 200psi

Foot Control Valve is an on-off valve which is operated by foot. The valve body and the foot rest is made up of aluminium alloy and the piston is spring loaded one. It is in the closes condition by means of the spring and when the foot rest is pressed the valve opens and the air to the operation.

This is a Electro Magnetic Valve and each valve is connected to different function of the component in the vehicle or machine. It is a three way two position valve and operate in 12V DC Solenoid valve. These Electro Magnetic Valves are made from excellent quality raw materials. Our Electro Magnetic Valves can be availed at industrial leading price.

Specifications :

Ryder Non Return Valve has a very low opening pressure and low differential for closing even at high operating pressure. The unit locks effectively in reverse directions at pressure differential as low as 0.1 kgf/cm2 . The unit is equally efficient in operation while handling fluids under pressure or vacuum. This valve is a self-aligning unit and hence can be mounted/ fitted in any position. However horizontal position is more desirable

Specifications :