Rudra Impex Corporation

Kalbadevi, Mumbai, Maharashtra

we are distributor for wika, danfoss, switzer , phoenix contact , leuze , flexicon ,

we provide you total solution , please contact us at following address

The more varied the tasks in electro technology, the more varied the components for the solution must be. The industrial connection technology from Phoenix Contact hence contains more than just modular terminal blocks.

Circuits Breakers:For the optimum protection of your systems, Phoenix Contact offers high-quality circuit breakers in the following versions:

• Thermal Circuit breakers TCP they are ideally suited as device protection for the AC & DC consumers, e.g. to protect motors, transformers and actuators against overloads.
• Thermo magnetic circuit breakers TMC they combine the advantages of the thermal and the magnetic trigger mechanisms and are typically used in information and communication technology as well as process control.
• Electronic Circuit breakers ECP they are designed specifically for the selective protection of all load circuits that are fed by a 24VDC power supply unit. They respond to overload or short circuit faster than the power supply unit, and they selectively disconnect this faulty load circuit before the power supply unit disconnects all connected loads to protect itself.

• Crimping Pliers For Insulated Pin/Ring Type Lugs
• Crimping Pliers range : 0.5 to 10Sqmm
• Crimping Pliers for Non-Insulated Lugs
• Crimping Pliers Range : 0.25 to 6Sqmm
• Relays From 1Channel /2/4/8/16 nos. on one board
• Hexagonal & Square Type Crimping

• Various variety of Stripping Pliers
• Stripping Tools for Conductors & Cables
• Wire Stripping Range : 0 to 11mm Diameter

• Various variety of Stripping Pliers
• Stripping Tools for Conductors & Cables
• Wire Stripping Range : 0 to 11mm Diameter

PHOENIX CONTACT PCB connectors have always fulfilled the high quality requirement of industrial electronics. As a world leader in the field of PCB connectors having more than 13000 different products, PHOENIX CONTACT offers solution to all types of your PCB termination requirements.

When it comes to designing your printed circuit board connection so that it is cost-effective, Service-friendly, and neatly arranged, the print terminals and the COMBICON range from PHOENIX CONTACT are the ideal choice. It consists of male female pluggable PCB connector. This range offers convenient and error free wiring solution. With two to twenty four pole options it offers a convenient tool to design PCB with as many numbers of terminations as required by customer. The polarity protection prevents wrong making of male & female Connectors.

The range is classified on the basis of :-

1] The pitch, Varying from 2.54mm to 15mm2] The wire size, ranging from 0.14 Sqmm to 16 Sqmm3] Termination principle of Screw, Spring & Crimp4] Various conductor entry direction i.e. Vertical, Horizontal and Angled5] Ampere rating 125A6] In direction parallel to the conductor Axis7] In direction vertical to the PCB. Connection point facing the rippled side of the header.8] With side panels plug in direction parallel to PCB.

The screw connection system is known and accepted worldwide as the most frequently used type of wire termination. Due to highest contact forces, top reliability is attained regardless of the conductor cross section from 0.14 to 240Sqmm.

The inline controller family is a modern, highly modular compact control system from Phoenix Contact Germany. It is designed for small to medium-sized applications.
Their open interfaces mean that they can be integrated in almost any network. The direct expandability using the Inline installation system allows the controllers to be adapted very flexibly to many application tasks. In addition, an INTERBUS remote bus can be configured as a bus branch in order to incorporate distributed sensors and actuators.
The ILC 150.and ILC 200controllers cover the lower performance range.
ILC 3xx expands the application range of inline controllers to medium sized applications. The integrated interface and the powerful processors together enable easy data communication.
With the ILC 3xx., the Ethernet interface serves as a connection to other controllers or systems. The IEC 61131-5 communication modules allow data to be exchanged between controllers. The TCP/IP communication blocks can exchange data with any TCP/IP- compatible devices and systems.The inline controllers are configured and programmed from start to finish using PC WorX in accordance with IEC 61131. The application programs are downloaded and tested either via Ethernet, INTERBUS or the local RS 232 programming interface, depending on the type of device.

Programme Logic Controller Features & Advantages.

• Interface: - Ethernet (10/100), Inline, PRG (Mini DIN).
• RUN/STOP/RESET Switch (no. key operated switch).
• Processing speed 1.5ms/1k instructions.
• Program memory approx 256k Byte.
• Data memory approx 256k Byte.
• 4096 I/O Handling capability.
• Retentive data memory 8k Byte.
• Internal parameterization memory with file Systems.
• Real time lock (Buffered)
• Base on Net technology.
• Programmable with PC WORX.
• Built in web server.
• Built in FTP server.
• Seperate power supply for logic, sensor & Actuator
• Colour coding for easy Connections.
• Remote handling capability.
• Built in diagnostics LEDS.
• Compact in size labeling & mark

Current transformers are used for monitoring load current in networks or great loads. They transform currents in the kA range to e.g. 0-1 A or 0-5 A. Thus large load currents can be evaluated and monitored by downstream automation devices. The new PACT analog current transformer portfolio offers a complete range of tubular bar, plug-on and wire-wrap transformers for measuring large currents of 1 A to 4000 A. Depending on the application requirements, almost 3000 different versions of different accuracy classes, capacities and sizes are available. Different mounting positions allow for use even in applications where space is critical.

Besides non-calibratable current Xmers, calibratable Xmers are offered, which become calibrated current Xmers after an additional calibrating process. On customer request, the calibration of the measuring transducers including the creation and handling over of all certificates can be processed by Phoenix Contact.

Relays are being used as the interface between the two circuits at same or different potential to archive:

• Electrical Isolation between the controller and the load side.
• For Signal Multification
• For Signal amplification
• And to interface different potential
• Relays From 1Channel /2/4/8/16 nos. on one board
• Relays with 1/2/4 Changeover
• With/ Without fuse protection with / without fuse blown indication
• Relays with Socket or Directly soldered on PCB
• Available Coil Voltage is 24V, 230VAC/110VAC

A wide range of automation equipment is used for control processes. Whether it is the startup of a small system with just a few I/O signals or a complex power station, both applications share a common requirement- the signals from the automation equipment must be connected to the field level as per the industry standards. INTERFACE cabling offers two wiring techniques: the VARIOFACE system cabling and the VARIOFACE wiring interfaces.

The VARIOFACE system cabling is a cabling concept that was developed especially to connect to various automation equipment. The system cabling comprises three harmonized components:

FRONT ADAPTERSYSTEM CABLECONTROLLER BOARD

Interface Cabling Features & Advantages :

• The System concept of varioface system cabling reduces manufacturing costs through fast, faultless and uniform wiring of the input and output signals of a PLC.
• Varioface Systems cabling is available for controllers from:ABBAllen BradleyEMERSONHoneywellGE FANUCMitsubishi ElectricOMRONSchneider ElectricSiemensYokogawa
• Simple planning using the project planning cross-list
• Cost reduction through time-saving wiring
• Fault minimization through protection against polarity reversal
• Easy maintenance through modular system components.
• Front adapters with an integrated pin strip (IEC 60603-13) are plugged onto the PLC I/O cards. They replace connection methods such as screw or crimp connection.

The range of temperature switches includes components for general industrial use as well as specialised switches for demanding applications.

The Danfoss range of temperature sensors is based on decades of global experience within the marine industry and in refrigeration plants - undoubtedly some of the toughest environments around. Even in these demanding surroundings you can trust our products; they have a long life thanks to their robust design.

Danfoss solenoid valve bodies and electrical coils are normally supplied separately and then combined.
They are assembled quickly and simply without tools, providing optimum product flexibility and availibility. If a coil does need to be replaced, it can be done without stopping or draining any system.
The solenoid valves are also available as assembled units if required.

The range of pressure switches includes components for general industrial use as well as specialised switches for demanding applications.

Danfoss pressure transmitters help you keep demanding industrial processes under control. Accurate, robust and built for long life, they perform reliably day after day, even in the harshest environments.

Danfoss coils are specially designed to operate in the aggressive environment with high humidity and temperature fluctuations found in most refrigeration systems. The clip-on fastening system ensures a faultless installation and makes the coils easy to mount or dismount. Clip-on coils are mounted without any tools at all, and it is simple to dismount the coil be means of a screwdriver. Clip-on coils are available for the entire range of Danfoss solenoid valves for refrigeration, freezing and air conditioning applications.

BV is a range of ATEX approved a.c. coils for use in EX zone 2 - Ex nA IIB T4 Gc (EN 60079-0 and EN 60079-15). The coils are suitable for the Danfoss solenoid valve range and cover the standard voltages and frequencies used in the market. The coils are embedded and with long lifetime - even under extreme conditons. Safe mounting with screw-on system.

Danfoss Oil Burner Components offer a complete range of components for monitoring and controlling oil burners in domestic and commercial applications. > See detailed burner information

Danfoss oil nozzle programme consists of a wide range for standard burner systems as well as a series of special nozzles adapted for different market demands as regards operating area, media and emission.

We produce nozzles in accordance with EN 293 and EN 299. Each nozzle is tested 100 per cent electronically and visually for function and uniformity.

Danfoss recommends to change the nozzle once a year out of consideration for environment and operating performance.

Achieve the lowest cost of ownership with a premier drive dedicated to ventilation, heating, and refrigeration applications.

Din rail for industrial application confirming to the European standard EN 60715 with third generation of Cr + Passivation for improved corrosion resistance and SST stability of 350Hrs. The biggest advantage is that it is fluoride free and organic acid free and has a low metal concentration

The DIN Rails are designed in accordance with the European Standard EN 60715 using state of the art production processes to ensure high dimensional accuracy, restricted tolerances and outstanding surface tempering. The Din Rails are available in standard lengths of 1M and 2M with or without mounting slots on request. We also provide Profile Cutters for individual processing.

All din rails are ROHS approved base metal cold rolled low carbon steel according to DIN & European standards EN10130

2nd generation passivations of Cr3+, light iridescence colour, higher thickness film 200nm400nm and improved corrosion resistance as compared to the 1st generation passivations. Our entire range of DIN rails are RoHS Compliant.

Processes are becoming more and more complex, thus safety aspect plays a large role here. It is therefore important to have measurement and control monitoring of drives in modern switchgear and control gear systems. The range from Phoenix Contact covers voltage and current monitoring for single phase and three phase networks and for consumers and controllers. Requirements pertaining to safety and system availability increase constantly regardless of the sector. Processes are becoming more and more complex, not only in the mechanical engineering and chemical industry but also in plant automation technology. Demands on power engineering are also constantly on the raise. Trouble free and therefore cost-effective operation can be achieved only with continuous monitoring of significant network and system parameters. Electronic monitoring relays of the EMD series are available for the widest varieties of monitoring tasks avoid consequences of errors or to keep them within times. The operating states are singled using colored LEDs and the errors that may occur can be sent to a controller through a potential-free contact or can shut down a section of the system. Some device versions are equipped with startup and response delays in order to briefly tolerate

measured values outside the fixed monitoring range.

Monitoring Relay: The monitoring modules of the EMD series offer a cost-effective solution for the monitoring task such as current, voltage, Phase parameters, coil temperature, motor load and fluid level

Timer Relay :A practical combination of functions and time setting ranges as well as devices with special functions (Star-Delta) are available for the timer relays of the ETD series.

Function Blocks :In the function blocks, simple functions down to the component level are packaged for industrial use and provided with professional connection methods.

Full Product Range :

• Single - Phase Power monitoring
• Single Phase Voltage monitoring
• Three Phase Voltage monitoring (Incl. Phase monitoring)
• Phase sequence monitoring
• Thermistor monitoring
• Voltage indication modules
• Load Monitoring
• Filling level monitoring

Advantages of using Electronic Monitoring Devices:

• Frequency range from 16.67 up to 400 Hz.
• Under or over voltage or over current detection.
• Phase sequence, phase failure and asymmetry recognition.

Our Switches with standard functions prove that a large scope of performance does not necessarily mean a high price. The complete program of SF switches includes nine devices with up to 16 ports suitable for industrial use. Up to three ports can be designed with multi-mode glass fibers. While the twisted-pair lines support transmission rates of 10 and 100 Mbps, the glass fiber lines are designed for 100 Mbps.

Features & Advantages:

• Fixed 8 & 16 RJ 45 Ports (10/100M Bit/s)
• Mixed RJ45 within 1 or 2 fiber optic ports [100M Bit/s, full duplex, SC-D]
• Potential free contact.
• Redundancy power.
• Din rail mounted.
• UL / CUL class 1 Div 2
• Plug & Play
• Certification : CUL, CUL-EX LIS, UL, UL-EX LIS
• Increasing the network performance by filtering the data traffic
• Simple network extension.
• Coupling of copper network segment with different transmission rates, since these are automatically detected
• Auto negotiation i.e. each copper port establishes a half or full duplex connection at 10 or 100 Mbps
• Auto Crossing, so that no distinction has to be made between 1:1 and cross-over lines
• Electrical isolation of network segments using FO ports.