Other Products / Services #542764

we are offering radar level. the reflex vf series range of tdr products is ideal for the measurement of liquids, powders and granules to a range of 60m. unaffected by pressure, temperature, viscosity, vacuum, foam, dust, changes in dielectric constant or coating of the probe, the vf series can measure virtually any product in either direct or tbf mode utilising any one of its seven probe types.

We are offering watson smith I to p converter.The 100x series is an open-loop, highly accurate proportional control valve. A rugged and reliable unit which has been proven in application installations globally. The uncomplicated design of the 100x101x enhances the reliability and reduces maintenance requirements, offering a cost effective accurate solution.

We are offering dust sequence controller.The programmable sequential controller is designed specifically for use with pneumatic dust collector systems. It is used to control the solenoid of the diaphragm valve in order to program the pulse jet sequence of the valves. Led lights serve as indication of status of pulse position and timing. Both the pulse jet timing and duration of each pulse jet could be adjusted by the logic circuitry. The controller has 2 independent "on" and "off" methods, the 1st is when the ac power supply is cut off, the controller will shut down.

We are offering silient features1. Truly universal input2. Onoff control output3. 4 digit led 0.8" 7-seg red led display4. User friendly calibration through software5. The control points are settable through key pad on front facia6. Cold junction compensation for tc input7. Open sensor detection

Stainless steel, resistive, Metal film Stainless steel, hermetically welded 04 bar to 0600 bar (-1 bar initial value is availableRelative pressure 12. . . 30 VDC 010 VDC, non-ratiometric *1) -40125C Reverse polarity, short circuit Meeting industrial standards

We are offering thermal level alarm.The sl-100 series utilizes the thermal dispersion principle of the dissipation of heat by liquid to detect the presence or absence of liquid as compared with air. A typical configuration uses two temperature detectors set within the tip of the sensor. One temperature detector is heated a few degrees above the other one. As the level of process liquid drop below the tip, the delta temperature rises and the output will change state.

It is designed for most critical requirements of liquid level in vessels under high pressure & temperature condition in petrochemicals, fertilizer and pharmaceuticals & chemical industries involving inflammable toxic liquid, high temp Liquids.

We are offering side mounted level indicator.Side mounted heavy duty tank level indicator are suitable for storage tanks, batch tank, day tank, receiver tank. It is simple & reliable devices for direct reading in atmospheric or pressurised tank application.

The microprocessor based Temperature Controller is a high quality and user friendly product that can satisfy the user. The temperature controller has complete functions and utilizes a microprocessor that enables it to deliver fast results. The temperature has enhanced features that is critical to the user and is expected to raise quality levels and to expand production performances.

The sample cooler is a compact unit, specially designed as per ASME SEC-VIII, Div-1 & ASME PTC-19.11 to handle high pressure & High temperature applications.

The Wedgewood USA make process pH sensor features the Plunger pH electrode design which permits 360 sensor mounting.The porous Teflon liquid junction resists fouling and chemical attack.

Bimetal thermometers are extremely simple in their construction and are as such widely used in industrial applications. In these instruments, temperature measurement is made by means of a bimetal sensor.

Fibreglass reinforced PP plastic enclosure guarantees great resistance to impact and chemical attack Counters power supply variations Pump Head - Suction & Discharge assembily made of PVDF suits all chemical used in industrial, wastewater treatment & potable water applications Use of ceramic balls as standard improves pumping reliability and chemical compatibility of the whole liquid end 4 models cover 1 to 60 litre per hour with an output pressure upto 20bar Reduction in spares stock holding

This general purpose liquid or gas switch package provides a complete solution for low flow pump or process protection with a 10A compact relay controller for actuation. The optional flash alarm brings immediate attention to low flow conditions. The short sensor is intended for use in pipe or ducting from 1/2 to 1-1/2; the long sensor is applied in 2 and up. The product is broadly selected for low or no-flow applications. Specify the appropriate sensor technology, length and material.

This general purpose switch package provides a complete solution for high level spill prevention with a fixed level switch point and 10A compact relay controller for pump or valve actuation. The optional flash alarm brings immediate attention to high level conditions. The product is typically selected for pressurized and/or highly corrosive bulk storage, day tank and waste sump applications. Specify the appropriate sensor technology, material and assembly dimension.

This general purpose switch package provides a complete solution for automatic filling or emptying of a tank between two adjustable level switch points with a 10A latching compact relay controller for pump or valve actuation. The product is typically selected for atmospheric day tank, process vessel and waste sump applications.

Specify the appropriate sensor technology and assembly dimensions. The AC powered relay controller has a latching 10A relay, adjustable time delay, LED indicators and NO or NC invert switch.

1. High turndown ratio of 40:1 for control valve.
2. All wetted parts are stainless steel with nitrated for longer life.
3. No need of i/p convertor, positioner and separate controller .all the functions are built into the system.
4. No choking problrm in the roboter as they are bellows operated.
5. Wide range of set pressure available.
6. Valve can be mounted in any position compare to self acting valve which requires mounting only in the horizontal pipelines.
7. For emergnecy handwheel is provided so that valve can be adjusted manually and plant can run without distrubance.
8. Availability of the system is very high which will reduce the frequent shuit -downs and production losses.
9. Air consumption is very minimal 300 nl/hr.
10. No need of maintaining the costly spares as the system is highly reliable and we can provide the services from bangalore office under emergency.

The Thermal Flow Switch Monitor SP-150 is based on the principle of thermal dispersion. A typical configuration uses two Temperature Detectors set within the tip of the sensor. One Temperature Detector is heated a few degrees above the other one. As the process medium flows over the tip of the sensor it disperses some of the heat from the heated Temperature Detector. The delta temperature is a function of flow velocity and converted into electronic signal. The open collector changes state once the set point has been reached.

Electronet's Series DPC-012 are Process Indicator / Controllers specially designed for various industrial applications. These can be used for monitoring and controlling parameters like Temperature, Pressure, Flow, Speed, Level etc. with the help of proper Sensors / Transmitters. The control points are settable through the potentiometers on front fascia and control output is available at the rare end.

The flow-captor 4120 is a unique, precise, metering flow switch with adjustable setpoint for industrial application. For the first time in flow technology it is possible to set an exact flow set-point and to simultaneously measure flow speed in applications where the use of conventional devices is restricted, due to lack of space, or where the price of such devices is not feasible.

Detcon Model Series 700 industrial gas detection sensors are a new generation of intelligent sensor modules. This new level of environmental durability includes an electropolished 316 stainless steel housing, multi-layered transient spike protection circuitry and 100% encapsulated electronics. The sensor electronics are completely protected and immune to water ingress and corrosion. The gas detector sensor elements are all plug-in components and can easily be replaced in the field.

Designed to detect a specific impurity in a binary gas mixture, the 212R is also well suited for monitoring one component in more complex mixtures where the other gases have the same ratio to each other or have similar thermal conductivity coefficients.

Analysis of oxygen has become a part of every industry that uses or produces gas or gas mixtures. Teledynes complete line of portable gas analyzers provides this vital analysis in a compact package operating without an external power source. Oxygen concentration in the sample gas stream is measured by Teledynes own advanced Micro-fuel Cell sensor specific to oxygen.

The high-accuracy and fast response of these units is ideal for measuring oxygen in hydrogen, nitrogen, argon, helium, acetylene, ethylene, butadiene, carbon dioxide, hydrocarbons and many other gases.

The detection of nitrogen is critical to determining system integrity in argon gas supply systems. TAIs Model 2120 provides fast and accurate analysis of nitrogen (indicative of air contamination) with field proven emission spectroscopic technology.

Teledynes Model 3000TA makes the task of trace oxygen analysis easier, faster and more precise than ever before. Simple menu choices, membrane command switches and a large LED display make setup and operation clear and quick.

Accurate detection of trace levels of moisture has been a challenge to the process world owing to the fact that high concentrations of water are present in the atmosphere; approximately 1% by volume in room air. Teledyne Analytical Instruments is familiar with this challenge, having successfully developed one of the broadest lines of trace ppb / ppm O2 analyzers commercially available. In developing our trace O2 line, we have had to contend with the fact that 209, 000 ppm of O2 is present in the atmosphere ready to jeopardize the analysis of typically less than 1 ppm of O2. Teledyne is utilizing 50 years of expertise in detecting trace oxygen to produce a complimentary line of trace moisture analyzers Series 8800.

The 9060 provides standard programmable automatic calibration and auto-purge outputs. The user can program the cal/purge sequence to an alarm relay for external indication. The 9060 has also been designed with a probe diagnostic loop to continuously monitor for probe impedance to ensure the sensor is functioning properly. The electronics self-calibrates all inputs every minute.

Teledynes Max 5 Combustion Efficiency Analyzer is the quick and easy way to fine tune boilers, furnaces, fireboxes and any commercial or industrial combustion process. With the Max 5s logical design and simple controls, its easy to obtain money saving combustion efficiency. At the push of a button, this unit calculates
efficiency and displays the results of burner adjustments without the need for charts or tables. In addition, the unit is compact and
completely portable, making it convenient to spot check in the most difficult locations.

From storage tanks to material producing processes in automatic factory. They require different piping, horozoutal , conveyor, weighing, arrangement , separate , coding, life testing equipment dust , collecting, and main in process automation. Material characteristic (moisture, s.g., size ) and equipment design (shape, stuff ) usually lead to accumulated or even decreasing material delivery flow problems in working flows.

This general purpose liquid or gas switch package provides a low flow detection solution for pump or process protection with a 1A relay interface for remote devices such as a PLC, SCADA or alarm. The short sensor is intended for use in pipe or ducting from 1/2 to 11/2; the long sensor is applied in 2 and up. The product is broadly selected for low or no-flow applications.

Specify the appropriate sensor technology, length and material. For pump, valve or alarm automation, package your flow switch with our remote relay controllers. The controllers feature 10A relays, adjustable time delays, LED indicators, and NO or NC invert switches.